范畴CL中的等化子和余等化子

设L是闭集格(即,对每个x∈L,Bx Copr(L),使得x=∨Bx),这也等价于Lop是空间式locale.闭集格以及闭集格间保任意并、保余素元的映射组成的范畴记作CL.引入了通过并半格构造闭集格的方法——并半格的闭集格化,并且利用这种方法给出了闭集格范畴CL中等化子、余等化子的具体构造.

态射的广义逆与等化子

本文以态射偶的等化子为工具研究态射的广义逆 ,对于态射 f,给出了 g为 f-,f D和 f+的充要条件 。

余Frame范畴中的等化子和余等化子结构

本文对余Frame范畴(以余Frame为对象,以余Frame同态为态射)中的等化子和余等化子的结构进行了研究。首先,利用子余Frame和嵌入映射构造了两个态射(具有相同论域和相同余论域)的等化子;其次,利用商余Frame和典型映射构造了两个态射(具有相同论域和相同余论域)的余等化子。本文的结果是对余Frame研究工作的补充和完善。

Self-repairing Al_(2)O_(3)-TiO_(2)coatings fabricated through plasma electrolytic oxidation with various cathodic pulse parameters

The influence of cathodic pulse parameters was evaluated on plasma electrolytic oxidation(PEO)coatings grown on 7075 aluminum alloy in a silicate-based electrolyte containing potassium titanyl oxalate(PTO)using pulsed bipolar waveforms with various cathodic duty cycles and cathodic current densities.The coatings were characterized by SEM,EDS,and XRD.EIS was applied to investigate the electrochemical properties.It was observed that the increase of cathodic duty cycle and cathodic current density from 20%and 6 A/dm^(2) to 40%and 12 A/dm^(2) enhances the growth rate of the inner layer from 0.22 to 0.75μm/min.Adding PTO into the bath showed a fortifying effect on influence of the cathodic pulse and the mentioned change of cathodic pulse parameters,resulting in an increase of the inner layer growth rate from 0.25 to 1.10μm/min.Based on EDS analysis,Si and Ti were incorporated dominantly in the upper parts of the coatings.XRD technique merely detectedγ-Al_(2)O_(3),and there were no detectable peaks related to Ti and Si compounds.However,the EIS results confirmed that the incorporation of Ti^(4+)into alumina changed the electronic properties of the coating.The coatings obtained from the bath containing PTO using the bipolar waveforms with a cathodic duty cycle of 40%and current density values higher than 6 A/dm^(2) showed highly appropriate electrochemical behavior during 240 d of immersion due to an efficient repairing mechanism.Regarding the effects of studied parameters on the coating properties,the roles of cathodic pulse parameters and PTO in the PEO process were highlighted.

Topos中的模糊对象和模糊范畴

在一个topos中引入模糊子对象的概念 ,给出了一个对象的元素x对一个模糊子对象的隶属度的定义 .在一个布尔topos中讨论了模糊子对象的运算 .最后给出了由toposC的模糊子对象构成的范畴FC ,研究了范畴FC的等化子性质 ,有限积性质 ,并证明了范畴FC有最终元存在 .

Girard Quantale范畴中的乘积

本文讨论了Girard Quantale范畴的乘积,并且给出了该乘积的结构,同时证明了此范畴中有等化子.

软集和模糊软集的范畴

为从范畴论的观点研究软集,分别建立了软集的范畴和模糊软集的范畴,并讨论了它们的topos性质.研究结果表明:软集的范畴有terminal object,finite products,equalizer和SC等topos性质;模糊软集的范畴有finite products,equalizer,terminal object和exponentials等topos性质.该成果对软集的研究具有一定的参考价值.

Plasma methods for preparing green catalysts: Current status and perspective

Most current catalyst preparation methods cause pollution to air, water and land with the use of hazardous chemicals, lengthy operation time, high energy input and excessive water usage. The development of green catalyst preparation is necessary to prevent and eliminate waste from each step of the catalyst preparation. We summarize recent progress in the application of cold plasmas for green catalyst preparation. Cold plasma preparation can reduce the catalyst size, improve the dispersion and enhance catalyst-support interaction with the use of less or no hazardous chemicals. These improvements also lead to the enhancement of catalyst activity and stability. An alternative room temperature electron reduction with a non-hydrogen plasma as an electron source was developed for the reduction of noble metal ions in which no hazardous chemical reducing agent or hydrogen was needed. This creates many opportunities for the development of supported catalysts with heat sensitive substrates, including metal organic frameworks （MOFs）, covalent organic framework（COFs）, high surface area carbon, peptide, DNA, proteins and others. A novel floating metal catalyst on a water（or solution） surface has been established. Template removal using low temperature cold plasmas also leads to the formation of high surface area porous materials with characteristics that are normally only obtainable with high temperature calcination, but sintering can be avoided. Micro combustion has been developed for the removal of carbon template using cold plasma. This is promising for preparing many structured oxides in a simple way with no use of auxiliary chemicals. Many opportunities exist for the use of cold plasmas to make multi-metallic oxides. Some future development ideas are addressed.

Structure and corrosion resistance of modified micro-arc oxidation coating on AZ31B magnesium alloy

A hydrophobic surface was fabricated on a micro-arc oxidation (MAO) treated AZ31 Mg alloys via surface modification with myristic acid. The effects of modification time on the wettability of the coatings were investigated using the contact angle measuring device. The surface morphologies and structure of the coatings were evaluated using SEM, XRD and FT-IR. The corrosion resistance was investigated by potentiodynamic polarization curves and long-term immersion test. The results showed that the water contact angle (CA) increases gradually with modification time from 0 to 5 h, the highest CA reaches 138° after being modified for 5 h, and the number and size of the micro pores are decreased. The modification method hardly alters crystalline structure of the MAO coating, but improves the corrosion resistance based on the much positive potential and low current density. Moreover, the corrosion resistance and hydrophobicity can be enhanced with increasing the alkyl chain. The wetting and spreading for the alkylcarboxylate with low surface energy become easier on the micro-porous surface, and alkylcarboxylate monolayer will be formed through bidentate bonding, which changes the surface micropores to a sealing or semi-sealing structure and makes the MAO coating dense and hydrophobic. All the results demonstrate that the modification process improves the corrosion protection ability of the MAO coating on AZ31B Mg alloy.

Microstructure and mechanical properties of Fe_3Al alloys prepared by MA-PAS and MA-HP

Fe3Al alloys with nearly full density were fabricated by plasma activated sintering（PAS） and hot pressing（HP） from mechanical alloyed Fe-28%Al（mole fraction） powders,respectively.It is found that A2-type Fe3Al alloys were obtained by PAS,and they had a heterogeneous grain size distribution,most areas had a grain size smaller than 500 nm,and other areas had a grain size of about 1 μm.Different to PAS,D03-type Fe3Al alloys with a grain size of of 1-2 μm were obtained by HP.The compression testing results show that yield strength values of Fe3Al alloys fabricated by PAS and HP are almost equal at an elevated temperature,and the compression yield strength was about 100 MPa for all at 800 ℃.The room temperature compression ductility of Fe3Al alloys by PAS was about 20%,which was superior to that of Fe3Al alloys prepared by HP and casting.

Microstructure and mechanical properties of Ti-43Al-9V alloy fabricated by spark plasma sintering

A fine-grained TiAl alloy with the composition of Ti-43Al-9V was prepared by mechanical milling and spark plasma sintering（SPS）.The relationship among sintering temperature,microstructure and mechanical properties was studied.The results show that the morphology of mechanical milling powder is regular with size in a range of 5-30 μm.Main phases of γ-TiAl,α2-Ti3Al and few B2 phase are observed in the SPS bulk samples.For samples sintered at 1150 °C,equiaxed crystal grain microstructure is achieved with size in a range of 300 nm-1 μm.With increasing SPS temperature to 1250 °C,the size of equiaxed crystal grains obviously increases,the microhardness decreases from HV592 to HV535,and the bending strength decreases from 605 to 219 MPa.Meantime,the compression fracture strength also decreases from 2601 to 1905 MPa,and the strain compression decreases from 28.95% to 12.09%.

Microstructure and mechanical properties of TiAl-based alloy prepared by double mechanical milling and spark plasma sintering

A fine-grained TiAl alloy with a composition of Ti-45Al-2Cr-2Nb-1B-0.5Ta-0.225Y （mole fraction, %） was prepared by double mechanical milling（DMM） and spark plasma sintering（SPS）. The relationship among sintering temperature, microstructure and mechanical properties was studied. The results show that the morphology of double mechanical milled powder is regular with size in the range of 20-40 μm and mainly composed of TiAl and Ti3Al phases. The main phase TiAl and few phases Ti3Al, Ti2Al and TiB2 were observed in the SPSed alloys. For samples sintered at 900 ℃ the equiaxed crystal grain microstructure is achieved with size in the range of 100-200 nm. With increasing the SPS temperature from 900 ℃to 1000 ℃ the size of equiaxed crystal grain obviously increases, the microhardness decreases from HV658 to HV616, and the bending strength decreases from 781 MPa to 652 MPa. In the meantime, the compression fracture strength also decreases from 2769 MPa to 2669 MPa, and the strain to fracture in compression increases from 11.69% to 17.76%. On the base of analysis of fractographies, it shows that the compression fracture transform of the SPSed alloys is intergranular rupture.

Plasma electrolytic oxidation of zircaloy-4 alloy with DC regime and properties of coatings

The plasma electrolytic oxidation（PEO） coatings on zircaloy？4 alloy were prepared in silicate,phosphate and pyrophosphate electrolyte systems or their combination by DC current regime.The proper processing parameters were determined and the coatings were evaluated by electrochemistry technique,micro-hardness,SEM and XRD.The results show that the coating prepared in pure silicate system is uneven and after the addition of phosphate solution,the homogeneity of the coating is still poor.The coating prepared in pure pyrophosphate electrolyte system is homogeneous,but its hardness value is low.After the addition of silicate into the pyrophosphate electrolytic system,both the uniformity and hardness of the coating are improved.The XRD results show that the phase compositions are m-ZrO2 and t-ZrO2,the addition of silicate is beneficial to the formation of t-ZrO2.The results of polarization curves show that the coatings prepared in pyrophosphate and the mixture of pyrophosphate and silicate have better corrosion resistance.

Microstructure and properties of plasma remelted AZ91D magnesium alloy

The surface of AZ91 D magnesium alloy was remelted by plasma beam. The microstructure, composition, hardness, wear and corrosion resistance of the plasma remelted layer（PRL） were characterized. The results show that there is extremely fine and dendrite structure in the PRL at low magnification observation, which is still composed of α-Mg and β-Mg17Al12 phases. But at high magnification observation, the microstructure of the PRL is equiaxial crystalline grains with size of 3-5 μm. And also the content of α-Mg phase decreases while that of β-Mg17Al12 increases and distributes more uniformly in α-Mg matrix compared with the substrate. The hardness of the PRL is much higher than that of the substrate. There are plastic deformation, grains uprooting and tearing evidence with tiny even dimples in the tensile fracture of the PRL, which are different from the substrate. Furthermore, the surface wear and corrosion resistance of AZ91 D are improved significantly after plasma remelting.

Influence of Atomic Hydrogen on Transparent Conducting Oxide During Hydrogenated Microcrystalline Si Preparation by PECVD

The hydrogen plasma degradation of transparent conduction oxides （TCO） is studied for hydrogenated microcrystalline Si（μc-Si：H）prepared by plasma enhanced chemical vapor deposition （PECVD）. TCO films such as SnO2 and SnO2/ZnO bi-layer films were exposed to atomic H at various substrate temperatures and for various treatment times. A decrease in the transmittance due to reduction by atomic H was scarcely observed for SnO2 / ZnO bi-layer,while a decrease for SnO2 was found to depend strongly on the substrate temperature. The resistivity of SnO2 films decreases significantly when substrate temperature exceeds 150℃in H-plasma. However, H-plasma treatment has little impact on the resistivity of SnO2/ZnO bi-layer film. The reason for the decrease in the transmittance is the appearance of metallic Sn on the surface, and under this condition no μc-Si： H film is deposited. SnO2/ZnO bi-layer is very effective for the suppression of the reduction of TCO during μc-Si：H deposition. The performance of microcrystalline silicon solar cells fabricated on ZnO/SnO2/glass is also investigated.

Doped-Chamber Deposition of Intrinsic Microcrystalline Silicon Thin Films and Its Application in Solar Cells

A series of microcrystalline silicon thin films were fabricated by very high frequency plasma enhanced chemical vapor deposition （VHF-PECVD） at different silane concentrations in a P chamber. Through analysis of the structural and electrical properties of these materials,we conclude that the photosensitivity slightly decreased then increased as the silane concentration increased,while the crystalline volume fraction indicates the opposite change. Results of XRD indicate that thin films have a （220） preferable orientation under certain conditions. Microcrystalline silicon solar cells with conversion efficiency 4. 7% and micromorph tandem solar cells 8.5% were fabricated by VHF-PECVD （p layer and i layer of microcrystalline silicon solar cells were deposited in P chamber）, respectively.

Surface plasmon resonance-induced visible-light photocatalytic performance of silver/silver molybdate composites

Novel silver/silver molybdate（Ag/Ag2MoO4） composites with surface plasmon resonance（SPR）-enhanced photocatalytic performance were successfully fabricated via a facile one-pot hydrothermal route with the presence of sodium dodecyl sulfate（SDS） in this study.The as prepared silver/silver molybdate（Ag/Ag2MoO4） composites were systematically characterized by X-ray diffraction（XRD）,scanning electron microscopy（SEM） and ultraviolet-visible diffuse reflectance absorption spectroscopy（DRS） in order to investigate their crystal structure,morphology and optical property as well.The photocatalytic activities of the composites were subsequently evaluated by their ability to degrade rhodamine B（RhB） under visible-light irradiation.Varies of controlled experiments were then carefully operated to gain a deep insight into the assembling of Ag/Ag2MoO4composites.It was found that preparation conditions such as pH,reaction time,and the amount of surfactant played important roles in the formation of composites with octahedral microstructures.And the composite obtained at 160 ℃ using 0.5 g of sodium dodecyl sulfate exhibited the highest photocatalytic performance under visible-light irradiation.Capture experiments were also conducted to clarify the function of different active species generated on the surface of Ag/Ag2MoO4during the photocatalytic process,in which both holes and ·OH radicals were found to play crucial role in photocatalytic removal of RhB under visible light irradiation.A possible photocatalytic mechanism of Ag/Ag2MoO4 was finally proposed on the basis of all the results to explain the higher photocatalytic activity of the octahedral Ag/Ag2MoO4 composites.It was inferred that the photoinduced ＂hot＂ electrons can quickly transfer from the Ag NPs to the conduction band of Ag2MoO4 and react with oxygen and H2O to generate a large quality of active radicals such as ·OH and ·O2^- because of the SPR effects.Besides,this SPR effects of Ag nanoparticles deposited on the surface of Ag2MoO4 can not only dramatically amplify its light absorption,especially in the visible region,but also promote the separation of photoexcited electron-hole pairs and effectively decrease electron-hole recombination.

Fe_(75)Zr_3Si_(13)B_9 magnetic materials prepared by spark plasma sintering

Fe75Zr3Si13B9 magnetic amorphous powders were fabricated by mechanical alloying. Bulk amorphous and nanocrystalline alloys with 20 mm in diameter and 7 mm in height were fabricated by the spark plasma sintering technology at different sintering temperatures. The phase composition, glass transition temperature （Tg）, onset crystallization temperature （Tx）, peak temperature （Tp） and super-cooled liquid region （ΔTx） of Fe75Zr3Si13B9 amorphous powders were analyzed by X-ray diffraction （XRD） and differential scanning calorimetry （DSC）. The phase transition, microstructure, mechanical properties and magnetic performance of the bulk alloys were discussed with X-ray diffractometer, scanning electron microscope （SEM）, Gleeble 3500 and vibration sample magnetometer （VSM）, respectively. It is found that with the increase in the sintering temperature at the pressure of 500 MPa, the density, compressive strength, micro-hardness and saturation magnetization of the sintering samples improved significantly, the amorphous phase began to crystallize gradually. Finally, the desirable amorphous and nanocrystalline magnetic materials at the sintering temperature of 863.15 K and the pressure of 500 MPa have a density of 6.9325 g/cm3, a compressive strength of 1140.28 MPa and a saturation magnetization of 1.28 T.

Effects of graphite content on microstructure and tribological properties of graphite/TiC/Ni-base alloy composite coatings

In order to reduce the friction coefficients and further improve the anti-wear properties of Ni-base alloy coatings reinforced by TiC particles,graphite/TiC/Ni-base alloy（GTN） coatings were prepared on the surface of 45 carbon steel.The effects of graphite content on the microstructure and tribological properties of the GTN coatings were investigated.The results show that the addition of graphite to the GTN coatings may greatly reduce the friction coefficients and improve their wear resistance.The 6.56GTN and 12.71GTN coatings exhibit excellent integrated properties of anti-friction and wear resistance under low and high loads,respectively.Under a low load,the wear mechanisms of the GTN coatings are mainly multi-plastic deformation with slight abrasive wear and gradually change into mixture of multi-plastic deformation,delamination and micro-cutting wear with the increase of graphite fraction.As the load increases,the main wear mechanisms gradually change from micro-cracks,micro-cutting and adhesive wear to micro-cutting and micro-fracture with the increase of graphite fraction.