Cadmium sulfide(CdS)is an n-type semiconductor with excellent electrical conductivity that is widely used as an electron transport material(ETM)in solar cells.At present,numerous methods for preparing CdS thin films h...Cadmium sulfide(CdS)is an n-type semiconductor with excellent electrical conductivity that is widely used as an electron transport material(ETM)in solar cells.At present,numerous methods for preparing CdS thin films have emerged,among which magnetron sputtering(MS)is one of the most commonly used vacuum techniques.For this type of technique,the substrate temperature is one of the key deposition parameters that affects the interfacial properties between the target film and substrate,determining the specific growth habits of the films.Herein,the effect of substrate temperature on the microstructure and electrical properties of magnetron-sputtered CdS(MS-CdS)films was studied and applied for the first time in hydrothermally deposited antimony selenosulfide(Sb_(2)(S,Se)_(3))solar cells.Adjusting the substrate temperature not only results in the design of the flat and dense film with enhanced crystallinity but also leads to the formation of an energy level arrangement with a Sb_(2)(S,Se)_(3)layer that is more favorable for electron transfer.In addition,we developed an oxygen plasma treatment for CdS,reducing the parasitic absorption of the device and resulting in an increase in the short-circuit current density of the solar cell.This study demonstrates the feasibility of MS-CdS in the fabrication of hydrothermal Sb_(2)(S,Se)_(3)solar cells and provides interface optimization strategies to improve device performance.展开更多
TiAl alloy bulk samples with the composition of Ti-45Al-5.5(Cr,Nb,B,Ta) (mole fraction, %) were prepared by high energy mechanical milling and spark plasma sintering (SPS) and then heat treatment. The microstructure a...TiAl alloy bulk samples with the composition of Ti-45Al-5.5(Cr,Nb,B,Ta) (mole fraction, %) were prepared by high energy mechanical milling and spark plasma sintering (SPS) and then heat treatment. The microstructure and mechanical properties after heat treatment of TiAl alloy prepared by SPS at different temperatures were studied. The results showed that the morphology of high energy mechanically milled powder was irregular and the average grain size was about decades micrometers. X-ray diffraction analysis showed that the mechanically milled powder was composed of two phases of TiAl and Ti3Al. The main phase of TiAl and few phases of Ti3Al and TiB2 were observed in the SPS bulk samples of Ti-45Al-5.5(Cr,Nb,B,Ta) alloy. For samples sintered at 900 °C and 1000 °C, the microstructure was duplex structure with some fine equiaxed gamma grains and thin needly TiB2 phases. With the SPS temperature increasing from 900 °C to 1000 °C, the micro-hardness was changed little, the compression strength increased from 1812 MPa to 2275 MPa and the compression ratio increased from 22.66% to 25.59%. The fractography results showed that the compression fracture transform of the SPS Ti-45Al-5.5(Cr,Nb,B,Ta) alloy was rgranular rupture.展开更多
Nitrogen plasma treatment effect on GS-CNFs （graphene seeted vertically aligned carbon nanofibers） has been studied. GS-CNFs were grown on nickel coated cupper substrates by DC-plasma CVD （chemical vapor deposition...Nitrogen plasma treatment effect on GS-CNFs （graphene seeted vertically aligned carbon nanofibers） has been studied. GS-CNFs were grown on nickel coated cupper substrates by DC-plasma CVD （chemical vapor deposition） at relatively low temperature. GS-CNFs were studied by SEM （scanning electron microscopy）, HR-TEM （high-resolution transmission electron microscopy）, XPS and Raman measurements. GS-CNFs are composed of cylindrical shaped having pure graphite sheets with about 5 μm length and nanometer size tips and roots diameter. Nitrogen plasma treatment causes nitrogen chemical etching on the graphene seeted carbon nanofibers were disordered its fine shape and increase the graphetization due to nitrogen incorporation.展开更多
Ag nanoparticles were fabricated on Si substrates by radio-frequency magnetron sputtering and thermal annealing treatments.It was found that Ag nanoparticles are ellipsoid at low annealing temperature,but the axis rat...Ag nanoparticles were fabricated on Si substrates by radio-frequency magnetron sputtering and thermal annealing treatments.It was found that Ag nanoparticles are ellipsoid at low annealing temperature,but the axis ratio decreases with the increase of annealing temperature,and a shape transformation from ellipsoid to sphere occurs when the temperature increases to a critical point.The experimental results showed that the surface plasmon resonances depend greatly on the nanoparticles'shape and size,which is in accordance with the theoretical calculation based on discrete dipole approximation.The results of forward-scattering efficiency(FSE) and light trapping spectrum(LTS) showed that Ag nanoparticles annealed at 400°C could strongly enhance the light harvest than those annealed at 300 and 500°C,and that the LTS peak intensity of the former is 1.7 and 1.5 times stronger than those of the later two samples,respectively.The conclusions obtained in this paper showed that Ag ellipsoid nanoparticles with appropriate size is more favorable for enhancing the light trapping.展开更多
基金supported by the National Natural Science Foundation of China(22275180)the National Key Research and Development Program of China(2019YFA0405600)the Collaborative Innovation Program of Hefei Science Center,CAS,and the University Synergy Innovation Program of Anhui Province(GXXT-2023-031).
文摘Cadmium sulfide(CdS)is an n-type semiconductor with excellent electrical conductivity that is widely used as an electron transport material(ETM)in solar cells.At present,numerous methods for preparing CdS thin films have emerged,among which magnetron sputtering(MS)is one of the most commonly used vacuum techniques.For this type of technique,the substrate temperature is one of the key deposition parameters that affects the interfacial properties between the target film and substrate,determining the specific growth habits of the films.Herein,the effect of substrate temperature on the microstructure and electrical properties of magnetron-sputtered CdS(MS-CdS)films was studied and applied for the first time in hydrothermally deposited antimony selenosulfide(Sb_(2)(S,Se)_(3))solar cells.Adjusting the substrate temperature not only results in the design of the flat and dense film with enhanced crystallinity but also leads to the formation of an energy level arrangement with a Sb_(2)(S,Se)_(3)layer that is more favorable for electron transfer.In addition,we developed an oxygen plasma treatment for CdS,reducing the parasitic absorption of the device and resulting in an increase in the short-circuit current density of the solar cell.This study demonstrates the feasibility of MS-CdS in the fabrication of hydrothermal Sb_(2)(S,Se)_(3)solar cells and provides interface optimization strategies to improve device performance.
基金Project (51001040) supported by the National Natural Science Foundation of ChinaProject (HITQNJS.2009.022) supported by Development Program for Outstanding Young Teachers in Harbin Institute of TechnologyProject (2012RFQXG109) supported by the Youth Science and Technology Innovation Talents
文摘TiAl alloy bulk samples with the composition of Ti-45Al-5.5(Cr,Nb,B,Ta) (mole fraction, %) were prepared by high energy mechanical milling and spark plasma sintering (SPS) and then heat treatment. The microstructure and mechanical properties after heat treatment of TiAl alloy prepared by SPS at different temperatures were studied. The results showed that the morphology of high energy mechanically milled powder was irregular and the average grain size was about decades micrometers. X-ray diffraction analysis showed that the mechanically milled powder was composed of two phases of TiAl and Ti3Al. The main phase of TiAl and few phases of Ti3Al and TiB2 were observed in the SPS bulk samples of Ti-45Al-5.5(Cr,Nb,B,Ta) alloy. For samples sintered at 900 °C and 1000 °C, the microstructure was duplex structure with some fine equiaxed gamma grains and thin needly TiB2 phases. With the SPS temperature increasing from 900 °C to 1000 °C, the micro-hardness was changed little, the compression strength increased from 1812 MPa to 2275 MPa and the compression ratio increased from 22.66% to 25.59%. The fractography results showed that the compression fracture transform of the SPS Ti-45Al-5.5(Cr,Nb,B,Ta) alloy was rgranular rupture.
文摘Nitrogen plasma treatment effect on GS-CNFs （graphene seeted vertically aligned carbon nanofibers） has been studied. GS-CNFs were grown on nickel coated cupper substrates by DC-plasma CVD （chemical vapor deposition） at relatively low temperature. GS-CNFs were studied by SEM （scanning electron microscopy）, HR-TEM （high-resolution transmission electron microscopy）, XPS and Raman measurements. GS-CNFs are composed of cylindrical shaped having pure graphite sheets with about 5 μm length and nanometer size tips and roots diameter. Nitrogen plasma treatment causes nitrogen chemical etching on the graphene seeted carbon nanofibers were disordered its fine shape and increase the graphetization due to nitrogen incorporation.
基金supported by the National Natural Science Foundation of China (Grant Nos. 61006050 and 51072051)the Natural Science Foundation of Beijing,China (Grant No. 2102042)+2 种基金the Fundamental Research Funds for the Central Universities (Grant No. 10QG24)the National High Technology Research and Development Program ("863" Project)(Grant No. 2011AA050507)the National Basic Research Program of China("973" Project)(Grant No. 2010CB93380)
文摘Ag nanoparticles were fabricated on Si substrates by radio-frequency magnetron sputtering and thermal annealing treatments.It was found that Ag nanoparticles are ellipsoid at low annealing temperature,but the axis ratio decreases with the increase of annealing temperature,and a shape transformation from ellipsoid to sphere occurs when the temperature increases to a critical point.The experimental results showed that the surface plasmon resonances depend greatly on the nanoparticles'shape and size,which is in accordance with the theoretical calculation based on discrete dipole approximation.The results of forward-scattering efficiency(FSE) and light trapping spectrum(LTS) showed that Ag nanoparticles annealed at 400°C could strongly enhance the light harvest than those annealed at 300 and 500°C,and that the LTS peak intensity of the former is 1.7 and 1.5 times stronger than those of the later two samples,respectively.The conclusions obtained in this paper showed that Ag ellipsoid nanoparticles with appropriate size is more favorable for enhancing the light trapping.
