期刊文献+
共找到6篇文章
< 1 >
每页显示 20 50 100
基于环氧沥青的机场道面材料及铺装层间性能研究
1
作者 童云斌 《国防交通工程与技术》 2024年第5期92-96,共5页
机场道面由于承受高负荷和频繁使用,容易出现轮辙、开裂等病害,传统沥青材料难以满足其耐久性要求。结合热拌环氧沥青与SMA-13级配,研发了一种新型机场道面环氧沥青及其混合料,进行了其强度形成规律、施工容留时间、路用性能及铺装层间... 机场道面由于承受高负荷和频繁使用,容易出现轮辙、开裂等病害,传统沥青材料难以满足其耐久性要求。结合热拌环氧沥青与SMA-13级配,研发了一种新型机场道面环氧沥青及其混合料,进行了其强度形成规律、施工容留时间、路用性能及铺装层间粘结性能研究。结果表明,环氧沥青及其混合料随养护时间增加强度逐步增强,掺量40%~50%时,60℃养护4 d即可达到最终强度;在170~180℃条件下,环氧沥青及其混合料施工容留时间约为2 h;环氧沥青混合料ESMA-13表现出优异的抗轮辙性能和抗裂性能,采用匹配性较强的环氧树脂粘结剂60℃层间抗剪强度大于2.3 MPa,可有效保证铺装层间安全性能。研究结果可为机场道面铺装提供理论依据和技术支持。 展开更多
关键词 机场道面 环氧沥青 容留时间 路用性能 粘层性能
下载PDF
熔融沉积3D打印材料粘接强度及模量预测研究 被引量:3
2
作者 张黎 王新宇 +3 位作者 李征 谷俊峰 阮诗伦 申长雨 《化工学报》 EI CAS CSCD 北大核心 2019年第7期2727-2736,F0004,共11页
主要介绍了一种用于预测熔融沉积模型(FDM)层间粘接强度的扩散修复模型。根据流变数据确定温度相关扩散模型,基于一维瞬态热分析预测FDM部件层间的扩散。将温度历史上的扩散系数对时间积分得到界面分子总扩散,进而得到层间粘接强度预测... 主要介绍了一种用于预测熔融沉积模型(FDM)层间粘接强度的扩散修复模型。根据流变数据确定温度相关扩散模型,基于一维瞬态热分析预测FDM部件层间的扩散。将温度历史上的扩散系数对时间积分得到界面分子总扩散,进而得到层间粘接强度预测模型。结果表明:不同打印条件下预测结果与测得的粘合强度结果的吻合度较好,且该模型经修正后也适用于FDM部件弹性模量的预测。通过三点弯曲实验与数值模拟的结果对比,验证了粘接强度及模量预测模型的可用性。因此,可以作为FDM打印件承载性能预测的有效模型。 展开更多
关键词 聚合物 熔融沉积成型 性能预测 扩散 数值模拟
下载PDF
聚乙烯复合带热缠绕弯管防腐层粘接性能评价
3
作者 冯少广 李彤 +2 位作者 张文明 李东阳 刘国豪 《油气储运》 CAS 北大核心 2022年第11期1319-1324,共6页
针对3PE直管道配套聚乙烯复合带热缠绕弯管防腐层的粘接问题,系统研究了弯管不同位置粘接性能的差异,并分析了测试温度及热水浸泡老化对防腐层粘接性能衰减的影响规律。结果表明,不同区域弯管防腐层的粘接性能存在较大差异。随着测试温... 针对3PE直管道配套聚乙烯复合带热缠绕弯管防腐层的粘接问题,系统研究了弯管不同位置粘接性能的差异,并分析了测试温度及热水浸泡老化对防腐层粘接性能衰减的影响规律。结果表明,不同区域弯管防腐层的粘接性能存在较大差异。随着测试温度的增加,防腐层与管体的剥离强度逐渐降低,热缠绕复合带的层间剥离强度均略低于胶层对FBE底层的剥离强度。随着在50℃热水中浸泡周期的增加,防腐层与管体的粘接性能呈现了初始阶段(0~60天)平稳但略有波动、后期(60~120天)快速降低的规律。针对聚乙烯复合带热缠绕工艺在搭接过渡区防腐层表面高低起伏、防腐层中间区域气泡夹杂及焊缝区的空鼓问题提出了改进建议,研究结果对管道防腐层安全服役具有参考意义。 展开更多
关键词 热煨弯管 聚乙烯复合带 防腐性能 剥离强度 耐热水浸泡
原文传递
Lymph node metastasis in early gastric cancer with submucosal invasion:Feasibility of minimally invasive surgery 被引量:22
4
作者 Do-Joong Park Hyeon-Kook Lee +5 位作者 Hyuk-Joon Lee Hye-SeungLee Woo-HoKim Han-Kwang Yang Kuhn-UkLee Kuk-JinChoe 《World Journal of Gastroenterology》 SCIE CAS CSCD 2004年第24期3549-3552,共4页
AIM:To explore the feasibility of pertorming minimally invasive surgery(MIS)on subsets of submucosal gastric cancers that are unlikely to have regional lymph node metastasis. METHODS:A total of 105 patients underwent ... AIM:To explore the feasibility of pertorming minimally invasive surgery(MIS)on subsets of submucosal gastric cancers that are unlikely to have regional lymph node metastasis. METHODS:A total of 105 patients underwent radical gastrectomy with lymph node dissection for submucosal gastric cancer at our hospital from January 1995 to December 1995.Besides investigating many clinicopathological features such as tumor size,gross appearance,and differentiation, we measured the depth of invasion into submucosa minutely and analyzed the clinicopathologic features of these patients regarding lymph node metastasis. RESULTS:The rate of lymph node metastasis in cases where the depth of invasion was<500 μm,500-2 000 μm,or >2 000 μm was 9%(2/23),19%(7136),and 33%(15/46), respectively(P<0.05).In univariate analysis,no significant correlation was found between lymph node metastasis and clinicopathological characteristics such as age,sex,tumor location,gross appearance,tumor differentiation,Lauren's classification,and lymphatic invasion.In multivariate analysis, tumor size(>4 cm vs≤2 cm,odds ratio=4.80, P=0.04)and depth of invasion(>2 000 μm vs ≤500 μm, odds ratio=6.81,P=0.02)were significantly correlated with lymph node metastasis.Combining the depth and size in cases where the depth of invasion was less than 500 μm, we found that lymph node metastasis occurred where the tumor size was greater than 4 cm.In cases where the tumor size was less than 2 cm,lymph node metastasis was found only where the depth of tumor invasion was more than 2 000 μm. CONCLUSION:MIS can be applied to submucosal gastric cancer that is less than 2 cm in size and 500 μm in depth. 展开更多
关键词 Surgical Procedures Minimally Invasive ADULT Aged Early Diagnosis Feasibility Studies FEMALE GASTRECTOMY Gastric Mucosa Humans Logistic Models Lymph Node Excision Lymphatic Metastasis Male Middle Aged Stomach Neoplasms
下载PDF
Modification of HDPE filling with pelagic clay
5
作者 ZHAO Liang ZHANG Peiping +2 位作者 ZHANG Dongli LIU Xuesong LU Huahua 《Global Geology》 2010年第2期108-112,共5页
In order to improve the properties of HDPE, the authors used the method of suspended diffusion for purification the pelagic clay, used silane coupling agent to increase its organic activation, and prepared the composi... In order to improve the properties of HDPE, the authors used the method of suspended diffusion for purification the pelagic clay, used silane coupling agent to increase its organic activation, and prepared the composites of organic pelagic clay/HDPE by inching them in different conditions. The affections of process conditions and quantity of pelagic clay to the properties of composites were analyzed by testing their mechanical properties, thermo stability and barrier properties. According to test the structure of composites, it is indicated that pelagic clay has good compatibility with HDPE. The result shows that the pelagic clay can improve mechanical properties, thermo stability and barrier properties of HDPE properties effectively. 展开更多
关键词 pelagic clay filling modification HDPE properties and structure
下载PDF
Interfacial microstructure of Cu Cr/1Cr18Ni9Ti bi-metal materials and its effect on bonding strength
6
作者 ZHANG Qiao LIANG ShuHua +1 位作者 ZOU JunTao YANG Qing 《Science China(Technological Sciences)》 SCIE EI CAS CSCD 2015年第5期825-831,共7页
The Cu Cr/1Cr18Ni9 Ti bi-metal materials were prepared by the solid-liquid bonding method. The microstructures, mechanical properties and formation mechanism of the bonding interface were studied. The results show tha... The Cu Cr/1Cr18Ni9 Ti bi-metal materials were prepared by the solid-liquid bonding method. The microstructures, mechanical properties and formation mechanism of the bonding interface were studied. The results show that there exists a serrated transition layer with a certain width at the interface of Cu Cr/1Cr18Ni9 Ti bi-metal materials, and the transition layer consists of Fe-based and Cu-based solid solutions. The elastic modulus and hardness reach the maximum values at the interface closing to the 1Cr18Ni9 Ti zone. The bonding temperature has a significant effect on the width and morphology of the transition layer. The interfacial bonding strength is at least 30% higher than that of the Cu Cr alloy, and the tensile fracture occurs at the side of the Cu Cr alloy rather than at the bonding interface. 展开更多
关键词 bonding modulus tensile interfacial SAED hardness closing polymerization Figure bonded
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部