岛津UV-265双光束紫外-可见分光光度计的维修和保养

简要介绍了岛津UV - 2 6 5双光束紫外 -可见分光光度计常见故障的维修和保养方法 ,提高仪器的使用水平和延长仪器的使用寿命 ,使仪器始终处于性能良好、计量可靠的状态下 ,充分发挥仪器的作用。

紫外分光光度法测定工业废水中的油含量

不同油类对同一特征波长紫外光的吸收有较大差异，为使标准样品与污染物的组合特征确保一致。选择被测工业废水的石油醚萃取油品，经纯化后作“标准油品”，以225nm为测定波长在005-50mg／L范围内，吸光度与油含量浓度关系符合比尔定律，相关系数r=0．9994回收率为98％-102％，相关标准偏差1．0％-2．1％，结果满意。工业废水中油的测定一般采用红外光度法，操作繁琐且重复性差。本文采用紫外光读法测定废水中的油含量，研究了不同油类的同一特征波长紫外线光吸收情况的差异，将被测水样的石油醚萃取油品，经脱水及去除石油醚后作为“标准油品”，确保标准油品与污染物的组合特征一致，使测定结果尽可能接近真实值，试验证明该方法操作简单。

蒸汽温润法对化橘红中柚皮苷含量的影响

通过超声波提取法对化橘红中的柚皮苷进行提取,采用蒸汽温润法进行软化操作,先对温润的时间和温润的温度进行了单因素探究,然后两个因素组合搭配,从而获得温度和时间的最佳组合。本实验采用紫外分光光度计对化橘红中的柚皮苷含量进行检测,结果表明:在其他条件不变的情况下,在本实验设置的梯度里,蒸汽温润法的最佳软化条件是在60℃蒸汽温润9 h。

Determination of the Content of Total Alkaloids in Different Solvent Extracts from Climbing Groundsel Herb Produced in Guizhou Province and Their Antibacterial Activity

[Objective] This study aimed to compare the contents of total alkaloids in different solvent extracts from climbing groundsel herb produced in Guizhou Province and their antibacterial activity. [Method] The content of total alkaloids was measured by UV spectrophotometry, and Oxford cups were used to investigate the antibacterial activity of each solvent extract. [Result] There was a good linear correlation between the absorbance measured by the UV spectrophotometer and the content of total al- kaloids within the concentration of 0.011 0-0.054 8 mg/ml at 207 nm, and the re- gression equation was Y=23.654X＋0.021, R=0. 999 7 and the average recovery rate was 99.2%. The contents of total alkaloids in 60% ethanol extract, 95% ethanol and water ethanol were 38.71, 52.25 and 60.50 mg/g, respectively. The 60% ethanol ex- tract had strong antibacterial activity against Streptococcus pneumoniae, Staphylo- coccus aureus and Escherichia coil; the water extractive had stronger antibacterial activity against Escherichia colr, 95% ethanol extract had weak antibacterial activity, with no inhibition of Pseudomonas aeruginosa. [Conclusion] This method is accurate, simple, with good repeatability, which can be used for the determination of alkaloids content of the climbing groundsel herb; there is no positive correlation between the content of total alkaloids in different solvent extracts of climbing groundsel herb and their antibacterial activity.

Hydrogenated Graphene as Metal-free Catalyst for Fenton-like Reaction

Carbonaceous catalysts are potential alternatives to metal catalysts. Graphene has been paid much attention for its high surface area and light weight. Here, hydrogenated graphene has been prepared by a simple gamma ray irradiation of graphene oxide aqueous suspension at room temperature. Transmission electron microscopic, element analysis, X-ray photoelectron spectroscopy, and UV-Vis spectrophotometer studies verified the hydrogenation of graphene. The as-prepared hydrogenated graphene can be used as a metal-free carbonaceous catalyst for the Fenton-like degradation of organic dye in water.

Preparation and infrared emissivities of alkali metal doped ZnO powders

Alkali metal(Li, Na, K) doped ZnO powders were synthesized by solid-state reaction at different calcination temperatures and holding time. Effects of holding time and K sources on the infrared emissivity of ZnO were investigated. The structure and surface morphologies of samples were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM). The UV-Vis absorption and infrared emissivities were investigated by a UV-Vis spectrophotometer and an infrared emissometer, respectively. XRD patterns confirm the wurtzite structure of the as prepared samples with single phase. Smooth grain surfaces are detected in all doped ZnO samples, while ZnO:Li and ZnO:Na present the aggregation of grains. The redshifts in the optical band-gap are observed in K-, Na-, and Li-doped ZnO with the values 3.150, 3.144, and 3.142 eV. Due to better crystalline quality, ZnO:K shows a lower emissivity than others. The emissivity of K-doped ZnO decreases to the minimum value(0.804), at 1200 °C and holding 2 h. Compared with KNO3 as K source, K2CO3 doped ZnO has lower emissivities.

An effective method and its modifications for isolation of high-quality total RNA from fruit pulps

An effective method for isolation of total RNA from pulps of mainly deciduous fruit trees was discussed in this paper. Here we shown that total RNA was successfully isolated from pulps of apple, peach and strawberry, but not grape berry via the effective CTAB method modified by ZENG, et al. However, total RNA was isolated from grape berry according to ZENG＇s protocols with a modification including 16% of β-Mercatoethanol and 3% of PVP in extraction buffer, 1/3 （V/V） of 5mol/L potassium acetate （KAC PH4.8） in supernatant. The detection of the isolated total RNA above using ultraviolet spectrophoto-metry, electrophoresis, reverse transcription and RT-PCR shown that the CTAB and its modifications is a preferred method for isolation of high-quality total RNA from fruit pulps.

A Comparative Study of Flavonoid Water-Ethanol Extraction Process in Planted Trollius Chinensis

With rutin standard sample as the comparison, flavonoid extraction rate as an indicator, UV-2450 ultraviolet visible light spectrophotometer to measure flavonoid content in planted Trollius chinensis through orthogonal experiment, this experiment optimizes process condition of flavonoid in Trollius chinensis through water extraction and ethanol extraction. The result shows that flavonoid extraction rate of Trollius chinensis through ethanol extraction method is obviously higher than water extraction, and the optimal extraction process condition is： ethanol concentration is 75%, extraction time is 90min, extraction times are 3, and fluid material ratio is 20：1.

Comprehensive Investigation to Analyze the Amino Acid Constituents of the Spent Silk Worm Pupae of Anthereaea assama

Spent silk worm pupae ofAntheraea assama were analyzed for its amino acid constituents and compared with the amino acid composition of fiber from A. assama, A. pyrni, and Bombyx mori. Amino acid percent was determined by UV Spectrophotometer at 570 nm. Infra Red spectra recorded the presence of different amino acids in the spent silk worm pupae powder which corroborate with the amino acids present in the fiber of different silk species.

Photocatalytic activity of bauxite-tailings supported nano-TiO_2

TiO2/bauxite-tailings （TiO2/BTs） composites were prepared via a chemical liquid deposition method and characterized by X-ray diffractometry （XRD）, scanning electronic microscopy （SEM） and N2 adsorption analysis. The photocatalytic performance of TiO2/BTs composites was evaluated with UV-Vis spectrophotometer following the changes of phenol concentration under different illumination time. Effects of the calcination temperature, the pH and the cycles on the photocatalytic activity of TiO2/BTs composites were investigated. The composites calcined at 500 and 600 ℃ exhibit the best photocatalytic performance, and the phenol degradation ratios reacting for 40 and 160 rain reach 35% and 78% respectively under the same conditions, higher than those of 29% and 76% of the Degussa P25（TiO2）. The ability of TiO2/BTs500 （BTs500 represents bauxite-tailings calcined at 500 ℃） composites to degrade phenol increases with decreasing pH.

Mixed P3HT/PCBM Organic Thin-Film Transistors： Relation between Morphology and Electrical Characteristics

The mixed P3HT （poly（3-hexylthiophene）） and [6,6]-PCBM （phenyl C61-butyric acid methyl ester） organic thin films were investigated for electronic structure using UV-Vis spectrophotometer and PESA （photo-electron spectroscopy in air）. Furthermore, ESR （electron spin resonance） and AFM （atomic force microscopy） were used to investigate the surface morphology and molecular orientation, respectively. ESR analysis indicated the molecular orientation of the P3HT crystalline in the blend thin films, which the crystalline oriented normal to the substrate with distribution of 35°. AFM images indicated that the surface morphology of P3HT film was affected by the presence of PCBM nanoparticles. Solution-processed OTFTs （organic thin-film transistors） based on P3HT/PCBM blend thin film in a top source-drain contact structure was fabricated, and the electrical characteristics of the devices were also investigated. A unipolar property with p-channel characteristics were obtained in glove box measurement.

Effects of four metal Ions on phenylalanine ammoni-alyase activities and flavonoids content of ginkgo biloba leaves

The enzyme activities of phenylalanine ammonia-lyase from six years old Ginkgo biloba leaves in the potted orchard were induced by four groups of metal ions respectively. The PAL activities and flavonoids content were measured by the UV-Vis spectrophotometer. Changes of the whole year were also studied. The results showed that four groups of metal ion treatments had significant effects on the PAL activities and flavonoids contents in Ginkgo leaves. The treatments with 0.1% and 0.3% FeSO4, 0.1%, 0.2% and 0.3% ZnSO4, 0.1%, 0.3% and 0.5% MnSO4, 0.1% and 0.4% CuSO4 not only enhanced flavonoids contents, but also extended the optimum harvest dates of ginkgo leaves. The optimum combination was 0.1% FeSO4, 0.2% ZnSO4, 0.3% MnSO4, and 0.4% CuSO4. It could improve flavonoids content up to 1.619 4%.

Effect of Agricultural Use of the Mixture Phosphogypsum/Natural Phosphate on the Dynamics of Phosphor in Soil and the Plant

The industrial production of the phosphoric acid is important and makes itself in a big number of countries. The by-product descended of this industry, residuary gypsum called phosphogypsum, poses a major environmental problem. The aim of this work is to identify and to value the potentialities of valorization of the by-product phosphogypsum produce in Morocco, for a use in the domain of agriculture. They can contain 1% to 6% of free acids. The idea is to use this acid to partially solubilize natural phosphate and to make the final product richer in phosphorus （about I0% of total P205 half soluble） and therefore more attractive on the agronomic and economic plan. For mixtures phosphogypsum/natural phosphate, a study of clarification is necessary, by varying the proportions of products, the humidities, mixing techniques, the ripening time to achieve a final interesting product. The dynamics of the phosphor in soil has been measured by the Olsen method and the one in the plant has been measured after drying in the steamroom to a temperature of 70 ~C to 75 ~C during 72 hours. A trial hold is incinerated. The ashes are taken by acid hydrochloric extract and the phosphor is measured out with the help of an UV spectrometer to 430 nm. The pH has been followed with the help of a pH-meter. The phosphor presents a remarkable dynamics in mixture with the phosphogypsum.

Hydrophobic Ti_xO_y-C_mH_n Nanoparticle Film Prepared by Plasma Enhanced Chemical Vapor Deposition

The hydrophobic films of TixOy-CmHn. deposited from mixture gases of titanium isopropoxide （TTIP） and oxygen by plasma enhanced chemical vapor deposition （PECVD） were investigated. The films were investigated by scanning electron microscope （ SEM ）, transmission electron microscope （ TEM ）, Fourier transform infrared spectrometer （ FTIR）, X-Ray diffraction （ XRD ）, element analysis （ EA ）, ultraviolet visible spectrometer （ UV-Vis）, and water contact angle （WCA）. The results reveal that the surface of the films is formed by mierosized papillaes aggregated by inorganic and organic phases of complex nanoparticles with size from 50 nm to 200 nm when the discharge power is increased from 40 W to 150 W. All fdms demonstrate the strong broad of Ti-O-Ti stretching vibration at 400 -800cm-1, -CH bending vibration at 1 388 cm -1, and broadening -OH stretching vibration at 3 000-3500 cm-1 With the increase of the discharge power, the asdeposited film changes from amorphous to crystallization. The WCA of the film can be as high as 160°, indicating the hydrophobicity. The films show a similar ultraviolet absorption property as the bulk TiO2 film. The composition of the composition of film deposited at 150 W can be formulated as Tio.302-C1.5H3. Therefore, the composition formula of this hydrophobic film could be expressed as TiO2-C5H10O4.7. It is believed that the complex micro/nano structures of TiO2 and C5H10O4.7 residues are responsible for the observed hydrophobicity and the ultraviolet absorption property of the film.

Synthesis of monoclinic structure gallium oxide film on sapphire substrate by magnetron sputtering

Gallium oxide （Ga203） films were deposited on singlecrystalline sapphire （0001） substrate by radio frequency （RF） magnetron sputtering technique in the temperature range of 300--500 ℃. The microstructure of the fl-Ga203 films were investigated in detail using X-ray diffractometer （XRD） and scanning electron microscope （SEM）. The results show that the film prepared at 500℃ exhibits the best crystallinity with a monoclinic structure （fl-Ga203）. Structure analysis reveals a clear out-of-plane orientation offl-Ga203 （201） II A1203 （0001）. The average transmittance of these films in the visible wavelength range exceeds 90%, and the optical band gap of the films varies from 4.68 eV to 4.94 eV which were measured by an ultraviolet-visible-near infrared （UV-vis-NIR） spectrophotometer. Therefore, it is hopeful that the fl-Ga203 film can be used in the UV optoelectronic devices.

Fabrication and characterization of transparent conducting titanium-zinc oxide nanostructured thin films

Nano transparent conducting titanium-zinc oxide(Ti-Zn O) thin films were prepared on glass substrates by radio frequency(RF) magnetron sputtering technique. The deposited films are characterized by X-ray diffraction(XRD), four-probe meter and UV-visible spectrophotometer. The effects of Ti-doping content on the structural, optical and electrical properties of the films are investigated. The XRD results show that the obtained films are polycrystalline with a hexagonal wurtzite structure and preferentially oriented in the(002) crystallographic direction. The structural and optoelectronic characteristics of the deposited films are subjected to the Ti-doping content. The Ti-Zn O sample fabricated with the Ti-doping content of 3%(weight percentage) possesses the best crystallinity and optoelectronic performance, with the highest degree of preferred(002) orientation of 99.87%, the largest crystallite size of 83.2 nm, the minimum lattice strain of 6.263×10^(-4), the highest average visible transmittance of 88.8%, the lowest resistivity of 1.18×10^(-3) Ω·cm and the maximum figure of merit(FOM) of 7.08×10~3 Ω^(-1)·cm^(-1). Furthermore, the optical bandgaps of the films are evaluated by extrapolation method and observed to be an increasing tendency with the increase of the Ti-doping content.

Synthesis and characterization of Cu_2ZnSnS_4 from Cu_2SnS_3 and ZnS compounds

The Cu2 Zn Sn S4(CZTS) powders are successfully synthesized by using Zn S and Cu2 Sn S3 as raw materials directly without any intermediate phase at 450 °C for 3 h in Ar atmosphere.The crystalline structure,morphology and optical properties of the CZTS powders are characterized by X-ray diffraction(XRD),Raman spectrum,field emission scanning electron microscopy(FESEM) and ultraviolet-visible(UV-vis) spectrophotometer,respectively.The results show that the band gap of the obtained CZTS is 1.53 e V.The CZTS film is fabricated by spin coating a mixture of CZTS powders and novolac resin with a weight percentage of 30%.The photoelectrical properties of such CZTS films are measured,and the results show an incident light density of 100 m W·cm-2 with the bias voltage of 0.40 V,and the photocurrent density can approach 9.80×10-5 A·cm2 within 50 s,giving an on/off switching ratio of 1.64.