Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent...Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent were used as diluents. The effect of α （DOP mass fraction in diluent） on the morphology and performance of the hollow fiber was investigated. With increasing α, the morphology of the resulting hollow fiber changes from typical cellular structure to mixed structure, and then to typical particulate structure. As a result, the permeability of the hollow fiber increases sharply, and the mechanical properties of the hollow fiber decrease obviously. It is suggested that the morphology and performances of iPP hollow fiber microporous membrane can be controlled via adjusting the compatibility between iPP and diluent.展开更多
A cell-free preparation obtained from extracts of activated Xenopus laevis eggs induced chromatin decondensation and nuclear formation from demembranated Xenopus sperm nuclei. Electron microscopy revealed that the rea...A cell-free preparation obtained from extracts of activated Xenopus laevis eggs induced chromatin decondensation and nuclear formation from demembranated Xenopus sperm nuclei. Electron microscopy revealed that the reassembled nucleus had a double-layered nuclear membrane, nuclear pore complexes, and decondensed chromatin etc. Indirect immunofluorescence analysis demonstrated the presence of lamina in newly assembled nuclei. Western-blotting results showed that lamin LII was present in egg extracts and in lamina of the reassembled nuclei which were previously reported to contain only eggderived lamin LIII.展开更多
A simple and cost-effective method has been developed for the fabrication of microtubular solid oxide fuel cells (MT-SOFCs). Highly asymmetric electrolyte hollow fibers composed of a thin dense skin layer and a thick ...A simple and cost-effective method has been developed for the fabrication of microtubular solid oxide fuel cells (MT-SOFCs). Highly asymmetric electrolyte hollow fibers composed of a thin dense skin layer and a thick porous substrate are first prepared by a modified phase inversion/sintering technique. The porous substrate is then formed into the anode by deposition of a Ni catalyst via an electroless plating method inside the pores while the thin dense skin layer serves directly as the electrolyte film of the fuel cells. A porous cathode layer is produced on the outer surface of the Ni-deposited hollow fibers by slurry coating and subsequent sintering to form a complete micro tubular fuel cell. The process has been employed to fabricate yttrium stabilized zirconia (YSZ) supported Ni-YSZ-YSZ-La0.6Sr0.4Co0.2Fe0.8O3-(LSCF) microtubular fuel cells. The maximum output of the resulting cells is 159.6 mW cm-2 at 800 °C when using H2 as the fuel feed and air as the oxidant.展开更多
基金Supported by the National Natural Science Foundation of China （No.20236030）.
文摘Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent were used as diluents. The effect of α （DOP mass fraction in diluent） on the morphology and performance of the hollow fiber was investigated. With increasing α, the morphology of the resulting hollow fiber changes from typical cellular structure to mixed structure, and then to typical particulate structure. As a result, the permeability of the hollow fiber increases sharply, and the mechanical properties of the hollow fiber decrease obviously. It is suggested that the morphology and performances of iPP hollow fiber microporous membrane can be controlled via adjusting the compatibility between iPP and diluent.
文摘A cell-free preparation obtained from extracts of activated Xenopus laevis eggs induced chromatin decondensation and nuclear formation from demembranated Xenopus sperm nuclei. Electron microscopy revealed that the reassembled nucleus had a double-layered nuclear membrane, nuclear pore complexes, and decondensed chromatin etc. Indirect immunofluorescence analysis demonstrated the presence of lamina in newly assembled nuclei. Western-blotting results showed that lamin LII was present in egg extracts and in lamina of the reassembled nuclei which were previously reported to contain only eggderived lamin LIII.
基金supported by the National Natural Science Foundation of China (20676073)
文摘A simple and cost-effective method has been developed for the fabrication of microtubular solid oxide fuel cells (MT-SOFCs). Highly asymmetric electrolyte hollow fibers composed of a thin dense skin layer and a thick porous substrate are first prepared by a modified phase inversion/sintering technique. The porous substrate is then formed into the anode by deposition of a Ni catalyst via an electroless plating method inside the pores while the thin dense skin layer serves directly as the electrolyte film of the fuel cells. A porous cathode layer is produced on the outer surface of the Ni-deposited hollow fibers by slurry coating and subsequent sintering to form a complete micro tubular fuel cell. The process has been employed to fabricate yttrium stabilized zirconia (YSZ) supported Ni-YSZ-YSZ-La0.6Sr0.4Co0.2Fe0.8O3-(LSCF) microtubular fuel cells. The maximum output of the resulting cells is 159.6 mW cm-2 at 800 °C when using H2 as the fuel feed and air as the oxidant.
