聚苯乙烯泡沫塑料与蜡料组合制模的研究

探讨了聚苯乙烯泡沫塑料与蜡料组合制模的精密铸造工艺,提出了组合模的粘结方法及脱模、焙烧工艺。

COUPLING MODEL OF EXTENDED MANUFACTURING ORGANIZATION AND ITS APPLICATION

For the feature of complex weapon manufacturing on internet,a coupling model is proposed.By using the model,the correlation between manufacturing cells in an extended manufacturing organization can be evaluated quantitatively,so an appropriate control plan is determined.A strategy to improve and reduce the coupling relationship of the organization is studied.A correlation matrix of extended tasks is built to analyze the relationship between sub-tasks and manufacturing resources.An optimization method for manufacturing resource configuration is presented based on the coupling model.Finally,a software system for analyzing coupling model about manufacturing organization on internet is developed,and the result shows that the coupling model is effective.

Modeling and control of a small solar fuel cell hybrid energy system

This paper describes a solar photovoltaic fuel cell (PVEC) hybrid generation system consisting of a photovoltaic (PV) generator, a proton exchange membrane fuel cell (PEMFC), an electrolyser, a supercapacitor, a storage gas tank and power conditioning unit (PCU). The load is supplied from the PV generator with a fuel cell working in parallel. Excess PV energy when available is converted to hydrogen using an electrolyser for later use in the fuel cell. The individual mathematical model for each component is presented. Control strategy for the system is described. MATLAB/Simulink is used for the simulation of this highly nonlinear hybrid energy system. The simulation results are shown in the paper.

Hybrid Dynamic Modeling and Control of Molten Carbonate Fuel Cell Stack Shutdown

A hybrid automaton modeling approach that incorporates state space partitioning, phase dynamic modeling and control law synthesis by control strategy is utilized to develop a hybrid automaton model of molten carbonate fuel cell (MCFC) stack shutdown. The shutdown operation is divided into several phases and their boundaries are decided according to a control strategy, which is a set of specifications about the dynamics of MCFC stack during shutdown. According to the control strategy, the specification of increasing stack temperature is satisfied in a phase that can be modeled accurately. The model for phase that has complex dynamic is approximated. The duration of this kind of phase is decreased to minimize the error caused by model approximation.

A novel design of power management integrated circuit with 90 plus efficiency used in AC/DC converter

Recently, resonant AC/DC converter has been accepted by the industry. However, the efficiency will be decreased at light load. So, a novel topology with critical controlling mode combined with resonant ones is proposed in this paper. The new topology can correspond to a 90 plus percent of power converting. So,a novel topology of an state of art integrated circuit, which can be used as power management circuit, has been designed based on the above new topology. A simulator which is specifically suitable for the power controller has been founded in this work and it has been used for the simulation of the novel architecture and the proposed integrated circuit.

Simulation of texture evolution and deformation mechanism in Mg-3Al-1Zn alloy during uniaxial compression

The effects of starting texture on he flow curves, and microstructure and texture evolutions of AZ31(Mg-3Al-1Zn-0.3Mn in wt.%) alloy during uniaxial compression at room temperature have been investigated by experiments and simulations. Two kinds of cylindrical compression samples were cut from the AZ31 extruded rod: one was cut with the compression direction parallel to the extruded direction(ED), and the other was cut with the compression axis perpendicular to the ED. The samples were termed as C//ED sample and C⊥ED sample, respectively. The results indicate that the general characteristics of flow curves and texture evolutions in both C⊥ED and C//ED samples during compression can be well explained by the relative activities of deformation mechanisms, which show a strong orientation dependence on the initial textures and the current texture. A significant yield behavior can be induced by {10-12} twinning at the starting deformation, and the lower yield stress in C⊥ED sample can be enhanced by the high activity of basal slip. The work hardening behavior is related to the activities of basal slip, pyramidal <c+a> slip, {10-12} twinning, as well as {10-11} twinning. However, the activity of prismatic slip is insensitive to the starting texture, and mostly negligible in all samples.

A euryarchaeal histone modulates strand displacement synthesis by replicative DNA polymerases

Euryarchaeota and Crenarchaeota, the two main lineages of the domain Archaea, encode different chromatin proteins and differ in the use of replicative DNA polymerases. Crenarchaea possess a single family B DNA polymerase(Pol B), which is capable of strand displacement modulated by the chromatin proteins Cren7 and Sul7 d. Euryarchaea have two distinct replicative DNA polymerases, PolB and PolD, a family D DNA polymerase. Here we characterized the strand displacement activities of Pol B and Pol D from the hyperthermophilic euryarchaeon Pyrococcus furiosus and investigated the influence of HPf A1, a homolog of eukaryotic histones from P. furiosus, on these activities. We showed that both Pol B and Pol D were efficient in strand displacement. HPf A1 inhibited DNA strand displacement by both DNA polymerases but exhibited little effect on the displacement of a RNA strand annealed to single-stranded template DNA. This is consistent with the finding that HPf A1 bound more tightly to double-stranded DNA than to a RNA:DNA hybrid. Our results suggest that, although crenarchaea and euryarchaea differ in chromosomal packaging, they share similar mechanisms in modulating strand displacement by DNA polymerases during lagging strand DNA synthesis.