The ultra high strength SiC particles （SiCp） reinforced Al-10%Zn-3.6%Mg-1.8%Cu-0.36%Zr-0.15% Ni composite was prepared by spray co-deposition. Microstructures of the extruded and different heat-treated bars were ana...The ultra high strength SiC particles （SiCp） reinforced Al-10%Zn-3.6%Mg-1.8%Cu-0.36%Zr-0.15% Ni composite was prepared by spray co-deposition. Microstructures of the extruded and different heat-treated bars were analyzed by transmission electron microscopy （TEM） and energy dispersive spectrometry （EDS）. Grain size of the composites prepared by two-stage solution is smaller than that by single-stage solution. After single-stage solution aging treatment, fine precipitates of both η and AlZnMgCu-rich phase can be found both intragranularly and intergranularly. While after the two-stage solution, an amorphous Si-Cu-Al-O （5 nm） layer appears at the interface. The addition of Ni and Zr modified the influence of the two-stage solution and inhibited the growth of the 7090/SiCp composite grain size. Heat treatments can significantly improve the fracture toughness of the composite. The fracture toughness first decreases then increases with the elongation of the aging time.展开更多
Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by emp...Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by employing the stir casting method.The structural properties of the produced samples were then investigated by optical microscopy and scanning electron microscopy;their mechanical properties were also addressed by hardness and tensile tests.The results showed that adding 1 vol.%TiO2 nanoparticles reduced the grain size and dendrite arm spacing by about 66%and 31%,respectively.Also,hardness,ultimate tensile strength,yield strength,and elongation of AA2024−1vol.%TiO2(np)composite were increased by about 25%,28%,4%and 163%,respectively,as compared to those of the monolithic component.The agglomerations of nanoparticles in the structure of nanocomposites were found to be a factor weakening the strength against the strengthening mechanisms.Some agglomerations of nanoparticles in the matrix were detected on the fractured surfaces of the tension test specimens.展开更多
An annealed 50 Cr V4 steel was subjected to cyclic heat treatment process that consists of repeated short-duration(200 s)held at 840 °C(above Ac3 temperature of 790 °C) and short-duration(100 s) held at 700 ...An annealed 50 Cr V4 steel was subjected to cyclic heat treatment process that consists of repeated short-duration(200 s)held at 840 °C(above Ac3 temperature of 790 °C) and short-duration(100 s) held at 700 °C(below Ac1 temperature of 710 °C). The spheroidization ratio of cementite and the average size of particles increase with increasing the cyclic number of heat treatment. After5-cycle heat treatment, the spheroidization ratio of cementite is 100%, and the average size of the cementite particles is about0.53 μm. After cyclic heat treatment, the hardness, ultimate tensile strength and yield strength of the experimental steel gradually decrease with increasing cyclic number of heat treatment. The elongation of the as-received specimens is about 7.4%, the elongation of the 1-cycle specimen is 14.3%, and the elongation of 5-cycle specimen reaches a peak value of 22.5%, thereafter marginally decreases to 18.3% after 6-cycle heat treatment. Accordingly, the fractured surface initially exhibits the regions of wavy lamellar fracture. By increasing the cyclic number of heat treatment cycles, the regions of dimples consume the entire fractured surface gradually. Some large dimples can be found in the fracture surface of the specimen subjected to six heat treatment cycles.展开更多
The aim of the present study was to investigate the influence of Mg addition and T6 heat treatment on microstructure,mechanical and tribological properties of the Al-Si-Cu-Mg alloys.In this context,a series of Al-12Si...The aim of the present study was to investigate the influence of Mg addition and T6 heat treatment on microstructure,mechanical and tribological properties of the Al-Si-Cu-Mg alloys.In this context,a series of Al-12Si-3Cu-(0.5-2.5)Mg(wt.%)alloys were produced by permanent mould casting,and then subjected to T6 treatment.Their microstructure and mechanical properties were investigated using OM,XRD,SEM,EDS along with hardness,tension,compression and Charpy impact tests.Dry sliding friction and wear properties of the alloys were studied using a ball-on-disk type tester.It was observed that the microstructure of as-cast Al-12Si-3 Cu-Mg alloys consisted of a(Al),Si,O-CuAb,0-Mg_(2)Si,0-AbMg_(8)Cu(2)Si_(6) and π-AhMg_(3)FeSi_(6) phases.T6 heat treatment gave rise to nearly spherodization of eutectic Si particles,formation of finer 0-CuAH and 0-Mg_(2)Si precipitates and elimination of Chinese script morphology of 0-Mg_(2)Si phase.The addition of Mg up to 2.5 wt.%decreased the hardness,tensile and compressive strengths,tensile elongation and impact toughness of the as-cast and T6-treated alloys and increased their friction coefficient and volume loss.T6 treatment,on the other hand,led to a significant increase in mechanical properties and wear resistance of as-cast alloys.展开更多
基金Project (02Gky2004) supported by Hunan Provincial Science and Technology Department, China
文摘The ultra high strength SiC particles （SiCp） reinforced Al-10%Zn-3.6%Mg-1.8%Cu-0.36%Zr-0.15% Ni composite was prepared by spray co-deposition. Microstructures of the extruded and different heat-treated bars were analyzed by transmission electron microscopy （TEM） and energy dispersive spectrometry （EDS）. Grain size of the composites prepared by two-stage solution is smaller than that by single-stage solution. After single-stage solution aging treatment, fine precipitates of both η and AlZnMgCu-rich phase can be found both intragranularly and intergranularly. While after the two-stage solution, an amorphous Si-Cu-Al-O （5 nm） layer appears at the interface. The addition of Ni and Zr modified the influence of the two-stage solution and inhibited the growth of the 7090/SiCp composite grain size. Heat treatments can significantly improve the fracture toughness of the composite. The fracture toughness first decreases then increases with the elongation of the aging time.
文摘Given the nonuse of TiO2 nanoparticles as the reinforcement of AA2024 alloy in fabricating composites by ex-situ casting methods,it was decided to process the AA2024−xTiO2(np)(x=0,0.5 and 1 vol.%)nanocomposites by employing the stir casting method.The structural properties of the produced samples were then investigated by optical microscopy and scanning electron microscopy;their mechanical properties were also addressed by hardness and tensile tests.The results showed that adding 1 vol.%TiO2 nanoparticles reduced the grain size and dendrite arm spacing by about 66%and 31%,respectively.Also,hardness,ultimate tensile strength,yield strength,and elongation of AA2024−1vol.%TiO2(np)composite were increased by about 25%,28%,4%and 163%,respectively,as compared to those of the monolithic component.The agglomerations of nanoparticles in the structure of nanocomposites were found to be a factor weakening the strength against the strengthening mechanisms.Some agglomerations of nanoparticles in the matrix were detected on the fractured surfaces of the tension test specimens.
文摘An annealed 50 Cr V4 steel was subjected to cyclic heat treatment process that consists of repeated short-duration(200 s)held at 840 °C(above Ac3 temperature of 790 °C) and short-duration(100 s) held at 700 °C(below Ac1 temperature of 710 °C). The spheroidization ratio of cementite and the average size of particles increase with increasing the cyclic number of heat treatment. After5-cycle heat treatment, the spheroidization ratio of cementite is 100%, and the average size of the cementite particles is about0.53 μm. After cyclic heat treatment, the hardness, ultimate tensile strength and yield strength of the experimental steel gradually decrease with increasing cyclic number of heat treatment. The elongation of the as-received specimens is about 7.4%, the elongation of the 1-cycle specimen is 14.3%, and the elongation of 5-cycle specimen reaches a peak value of 22.5%, thereafter marginally decreases to 18.3% after 6-cycle heat treatment. Accordingly, the fractured surface initially exhibits the regions of wavy lamellar fracture. By increasing the cyclic number of heat treatment cycles, the regions of dimples consume the entire fractured surface gradually. Some large dimples can be found in the fracture surface of the specimen subjected to six heat treatment cycles.
文摘The aim of the present study was to investigate the influence of Mg addition and T6 heat treatment on microstructure,mechanical and tribological properties of the Al-Si-Cu-Mg alloys.In this context,a series of Al-12Si-3Cu-(0.5-2.5)Mg(wt.%)alloys were produced by permanent mould casting,and then subjected to T6 treatment.Their microstructure and mechanical properties were investigated using OM,XRD,SEM,EDS along with hardness,tension,compression and Charpy impact tests.Dry sliding friction and wear properties of the alloys were studied using a ball-on-disk type tester.It was observed that the microstructure of as-cast Al-12Si-3 Cu-Mg alloys consisted of a(Al),Si,O-CuAb,0-Mg_(2)Si,0-AbMg_(8)Cu(2)Si_(6) and π-AhMg_(3)FeSi_(6) phases.T6 heat treatment gave rise to nearly spherodization of eutectic Si particles,formation of finer 0-CuAH and 0-Mg_(2)Si precipitates and elimination of Chinese script morphology of 0-Mg_(2)Si phase.The addition of Mg up to 2.5 wt.%decreased the hardness,tensile and compressive strengths,tensile elongation and impact toughness of the as-cast and T6-treated alloys and increased their friction coefficient and volume loss.T6 treatment,on the other hand,led to a significant increase in mechanical properties and wear resistance of as-cast alloys.
