Objective: To evaluate the osteocompatibility of D, L-polylactic/hydroxyapatite/decalcifying bone matrix (PDLLA/HA/DBM), and compare with PDLLA and DBM. Methods: Human primary osteoblasts isolated from the femoral hea...Objective: To evaluate the osteocompatibility of D, L-polylactic/hydroxyapatite/decalcifying bone matrix (PDLLA/HA/DBM), and compare with PDLLA and DBM. Methods: Human primary osteoblasts isolated from the femoral head of patients were inoculated onto PDLLA/HA/DBM, PLA and DBM respectively. The proliferation rate and collagen Ⅰ expression were detected. The interface between biomaterial and osteoblasts was investigated with phase contrast microscopy and electron scanning microscopy. Results: Best proliferation rate was observed with the PDLLA/HA/DBM and followed by DBM and PLA, suggesting that PDLLA/HA/DBM satisfying most requirements for the cultivation of human osteoblasts. Scanning electron microscopy showed the morphology of osteoblasts was correlated with the proliferation data. The cells, well spread and flattened, were attached closely on the surface of biomaterial with an arched structure and had normal morphology. The extracellular collagenous matrixs covered the surface of biomaterial and packed the granules of biomaterial. Conclusion: PDLLA/HA/DBM can form osteointerface early and have a good biocompability.展开更多
This paper aims to prepare a PVA-GAG-COL composite with polyvinyl alcohol (PVA), glycosaminoglycan (GAG) and collagen (COL) by the method of freeze drying and to investigate the feasibility as a tissue engineering sca...This paper aims to prepare a PVA-GAG-COL composite with polyvinyl alcohol (PVA), glycosaminoglycan (GAG) and collagen (COL) by the method of freeze drying and to investigate the feasibility as a tissue engineering scaffold for tissue or organ repairing. In this study, SEM was used to observe the morphology. Biocompatibility was tested by cell culture with the extracted fluid of composite materials. Different proportional scaffolds could be obtained with different concentrations and alcoholysis degree of PVA. Different proportional scaffolds also had different porous structures. SEM proved that large amount of porous structure could be formed. Biocompatibility test showed that the extracted fluid of composite materials was nontoxic, which could promote the adhesion and proliferation of the fibroblast. Fibroblast could grow on the scaffold normally.A porous scaffold for tissue engineering with high water content can be fabricated by PVA, GAG and COL, which has excellent cell biocompatibility. The porous structure shows potential in tissue engineering and cell culture.展开更多
Biocompatibility of dental porcelain is of crucial importance to the long-term success of dental prostheses because of its close contact with oral tissues for extended periods. This investigation was aimed to evaluate...Biocompatibility of dental porcelain is of crucial importance to the long-term success of dental prostheses because of its close contact with oral tissues for extended periods. This investigation was aimed to evaluate cellular responses to locally produced dental porcelain （Universiti Sains Malaysia, Malaysia） after a short-term subcutaneous implantation in a rat model. Locally produced dental porcelains supplied in disc form were implanted subcutaneously into 12 Sprague-Dawley male albino rats, which were sacrificed in groups of 3 at 1, 2, 3 and 4 weeks after implantation. A semi-quantitative histological analysis of the tissue surrounding implanted discs was done under an image analyzer after staining with hematoxyline and eosin. The macrophage was clearly the dominant cell type at the implant surface at the first week after implantation, followed by a gradual decrease as the implantation period increased. On the contrary, fibroblasts and fibrocytes were the dominant cell types in the tissue surrounding the implanted discs at the third and fourth week after implantation with the appearance of mature collagen. From pathological point of view, the disappearance of inflammatory cellular responses and the well matured fibrous connective tissue surrounding the implanted discs indicate a satisfactory in vivo biocompatibility.展开更多
Forming a stable anti-corrosion surface layer on magnesium(Mg)and its alloys has become a major challenge in developing a desirable degradable medical implant in bone.In this study,a porous MgO layer was first formed ...Forming a stable anti-corrosion surface layer on magnesium(Mg)and its alloys has become a major challenge in developing a desirable degradable medical implant in bone.In this study,a porous MgO layer was first formed on Mg by plasma electrolytic oxidation(PEO),and then a Mg-Al layered double hydroxide(LDH)layer was prepared to seal the porous structure of the PEO layer(LDH-2h and LDH-12h)via hydrothermal treatment.The bilayer structure composite coating,which can effectively resist the penetration of surrounding media,is similar to plain Chinese tiles.The in vitro results revealed that compared with other coatings,the LDH-12h composite coating can reduce the release of Mg ions and induce a milder change in pH when immersed in phosphate-buffered saline(PBS).In vitro rat bone marrow stem cell(rBMSC)culture suggested that the LDH-12h composite coating is favorable for cell activity,proliferation and could improve the osteogenic activity of rBMSCs.A subcutaneous implantation test revealed that the as-prepared sample showed enhanced corrosion resistance and histocompatibility in vivo,especially in the LDH-12h group.Moreover,LDH-12h had the lowest rate of degradation and the closest combination with the new bone after being inserted into a rat femur for 12 weeks with no major organ dysfunction.In summary,the asprepared PEO/Mg-Al LDH composite coating is able to improve the corrosion resistance and biocompatibility of Mg and to enhance osteogenic activity in vivo,suggesting its promising prospects for orthopedic applications.展开更多
OBJECTIVE: To study the adhesion, migration and three-dimentional growth of Schwann cells on PLA (polylactic acid) nonspinning fibre cloth and polyglycolic/polylactic acid (PLGA) fibres. METHODS: Schwann cells/ECM gel...OBJECTIVE: To study the adhesion, migration and three-dimentional growth of Schwann cells on PLA (polylactic acid) nonspinning fibre cloth and polyglycolic/polylactic acid (PLGA) fibres. METHODS: Schwann cells/ECM gel solution and PLA nonspinning fibre cloth and PLGA fibres pretreated by collagen, polylysine and ECM were co-cultured. Then the migration and three-dimensional growth of Schwann cells on the fibres were observed under phase contrast microscope and laser scanning confocal microscope. RESULTS: Schwann cell/ECM solution was compounded with PLA nonspinning fibre cloth. With formation of gel, most Schwann cells resided in the fibre net holes, and adhered to the fibres to form a multiplayer-arranged Schwann cell column like Bungner band. Schwann cells could adhere to PLGA fibres and grew and migrated along the fibres. ECM gel could significantly increase the adhering and migrating cell number. CONCLUSIONS: ECM gel can facilitate the adhesion, growth and migration of Schwann cells on the seteroframe. It is a good integrating material for tissue engineering bioartificial nerve.展开更多
Objective： To develop a novel scaffolding method for the copolymers poly lactide-co-glycolide acid （PLGA） to construct a three-dimensional （3-D） scaffold and explore its biocompatibility through culturing Schwann...Objective： To develop a novel scaffolding method for the copolymers poly lactide-co-glycolide acid （PLGA） to construct a three-dimensional （3-D） scaffold and explore its biocompatibility through culturing Schwann cells （SCs） on it. Methods： The 3-D scaffolds were made by means of melt spinning, extension and weaving. The queueing discipline of the micro-channels were observed under a scanning electronic microscope （SEM）.The sizes of the micropores and the factors of porosity were also measured. Sciatic nerves were harvested from 3-day-old Sprague Dawley （SD） rats for culture of SCs. SCs were separated, purified, and then implanted on PLGA scaffolds, gelatin sponge and poly-L-lysine （PLL）-coated tissue culture poly-styrene （TCPS） were used as biomaterial and cell-supportive controls, respectively. The effect of PLGA on the adherence, proliferation and apoptosis of SCs were examined in vitro in comparison with gelatin sponge and TCPS. Results： The micro-channels arrayed in parallel manners, and the pore sizes of the channels were uniform. No significant difference was found in the activity of Schwann cells cultured on PLGA and those on TCPS （P〉0.05）, and the DNA of PLGA scaffolds was not damaged. Conclusion： The 3-D scaffolds developed in this study have excellent structure and biocompatibility, which may be taken as a novel scaffold candidate for nerve-tissue engineering.展开更多
The objective of this paper is to design a based on composite membrane with certain mechanical porous polyvinyl alcohol （PVA） strength and biocompatibilities serving as tissue regenerative scaffolds. PVA-glycosamino...The objective of this paper is to design a based on composite membrane with certain mechanical porous polyvinyl alcohol （PVA） strength and biocompatibilities serving as tissue regenerative scaffolds. PVA-glycosaminoglycan （GAG）-type I collagen （COL） composite membrane was fabricated by PVA with different molecular weight （Mw） and alcoholysis degree （AD） being blended with certain amounts of GAG and COL and dried at 38~C for 24 h. The water content of the composite membranes were from 61.9% to 95.1% and swelling ratio ranged from 123.6% to 621.7%. Scanning electron micro- scope （SEM） analysis proved that PVA-GAG-COL composite membrane has porous and homogenous structure. Biocompatibility test results showed that the composite membrane was nontoxic, which could promote adhesion and proliferation of fibroblasts on the com- posite membrane. In conclusion, PVA-GAG-COL composite membrane with high water content and swelling ratio, suitable mechanical strength and good biocompatibility, has potential in tissue engineering and regenerative medicine.展开更多
文摘Objective: To evaluate the osteocompatibility of D, L-polylactic/hydroxyapatite/decalcifying bone matrix (PDLLA/HA/DBM), and compare with PDLLA and DBM. Methods: Human primary osteoblasts isolated from the femoral head of patients were inoculated onto PDLLA/HA/DBM, PLA and DBM respectively. The proliferation rate and collagen Ⅰ expression were detected. The interface between biomaterial and osteoblasts was investigated with phase contrast microscopy and electron scanning microscopy. Results: Best proliferation rate was observed with the PDLLA/HA/DBM and followed by DBM and PLA, suggesting that PDLLA/HA/DBM satisfying most requirements for the cultivation of human osteoblasts. Scanning electron microscopy showed the morphology of osteoblasts was correlated with the proliferation data. The cells, well spread and flattened, were attached closely on the surface of biomaterial with an arched structure and had normal morphology. The extracellular collagenous matrixs covered the surface of biomaterial and packed the granules of biomaterial. Conclusion: PDLLA/HA/DBM can form osteointerface early and have a good biocompability.
基金National High-tech Reasearch and Development Program of China(863 Program)grant number:2077AA09Z436+1 种基金Guangdong Project '211'grant number:50621030
文摘This paper aims to prepare a PVA-GAG-COL composite with polyvinyl alcohol (PVA), glycosaminoglycan (GAG) and collagen (COL) by the method of freeze drying and to investigate the feasibility as a tissue engineering scaffold for tissue or organ repairing. In this study, SEM was used to observe the morphology. Biocompatibility was tested by cell culture with the extracted fluid of composite materials. Different proportional scaffolds could be obtained with different concentrations and alcoholysis degree of PVA. Different proportional scaffolds also had different porous structures. SEM proved that large amount of porous structure could be formed. Biocompatibility test showed that the extracted fluid of composite materials was nontoxic, which could promote the adhesion and proliferation of the fibroblast. Fibroblast could grow on the scaffold normally.A porous scaffold for tissue engineering with high water content can be fabricated by PVA, GAG and COL, which has excellent cell biocompatibility. The porous structure shows potential in tissue engineering and cell culture.
文摘Biocompatibility of dental porcelain is of crucial importance to the long-term success of dental prostheses because of its close contact with oral tissues for extended periods. This investigation was aimed to evaluate cellular responses to locally produced dental porcelain （Universiti Sains Malaysia, Malaysia） after a short-term subcutaneous implantation in a rat model. Locally produced dental porcelains supplied in disc form were implanted subcutaneously into 12 Sprague-Dawley male albino rats, which were sacrificed in groups of 3 at 1, 2, 3 and 4 weeks after implantation. A semi-quantitative histological analysis of the tissue surrounding implanted discs was done under an image analyzer after staining with hematoxyline and eosin. The macrophage was clearly the dominant cell type at the implant surface at the first week after implantation, followed by a gradual decrease as the implantation period increased. On the contrary, fibroblasts and fibrocytes were the dominant cell types in the tissue surrounding the implanted discs at the third and fourth week after implantation with the appearance of mature collagen. From pathological point of view, the disappearance of inflammatory cellular responses and the well matured fibrous connective tissue surrounding the implanted discs indicate a satisfactory in vivo biocompatibility.
基金the National Natural Science Foundation of China(81901048,81921002,81620108006 and 31771044)Shanghai Committee of Science and Technology,China(18410760600)the International Partnership Program of Chinese Academy of Sciences(GJHZ1850)。
文摘Forming a stable anti-corrosion surface layer on magnesium(Mg)and its alloys has become a major challenge in developing a desirable degradable medical implant in bone.In this study,a porous MgO layer was first formed on Mg by plasma electrolytic oxidation(PEO),and then a Mg-Al layered double hydroxide(LDH)layer was prepared to seal the porous structure of the PEO layer(LDH-2h and LDH-12h)via hydrothermal treatment.The bilayer structure composite coating,which can effectively resist the penetration of surrounding media,is similar to plain Chinese tiles.The in vitro results revealed that compared with other coatings,the LDH-12h composite coating can reduce the release of Mg ions and induce a milder change in pH when immersed in phosphate-buffered saline(PBS).In vitro rat bone marrow stem cell(rBMSC)culture suggested that the LDH-12h composite coating is favorable for cell activity,proliferation and could improve the osteogenic activity of rBMSCs.A subcutaneous implantation test revealed that the as-prepared sample showed enhanced corrosion resistance and histocompatibility in vivo,especially in the LDH-12h group.Moreover,LDH-12h had the lowest rate of degradation and the closest combination with the new bone after being inserted into a rat femur for 12 weeks with no major organ dysfunction.In summary,the asprepared PEO/Mg-Al LDH composite coating is able to improve the corrosion resistance and biocompatibility of Mg and to enhance osteogenic activity in vivo,suggesting its promising prospects for orthopedic applications.
基金This study was supported by the National Natural Science Foundation of China(No.30100190)
文摘OBJECTIVE: To study the adhesion, migration and three-dimentional growth of Schwann cells on PLA (polylactic acid) nonspinning fibre cloth and polyglycolic/polylactic acid (PLGA) fibres. METHODS: Schwann cells/ECM gel solution and PLA nonspinning fibre cloth and PLGA fibres pretreated by collagen, polylysine and ECM were co-cultured. Then the migration and three-dimensional growth of Schwann cells on the fibres were observed under phase contrast microscope and laser scanning confocal microscope. RESULTS: Schwann cell/ECM solution was compounded with PLA nonspinning fibre cloth. With formation of gel, most Schwann cells resided in the fibre net holes, and adhered to the fibres to form a multiplayer-arranged Schwann cell column like Bungner band. Schwann cells could adhere to PLGA fibres and grew and migrated along the fibres. ECM gel could significantly increase the adhering and migrating cell number. CONCLUSIONS: ECM gel can facilitate the adhesion, growth and migration of Schwann cells on the seteroframe. It is a good integrating material for tissue engineering bioartificial nerve.
文摘Objective： To develop a novel scaffolding method for the copolymers poly lactide-co-glycolide acid （PLGA） to construct a three-dimensional （3-D） scaffold and explore its biocompatibility through culturing Schwann cells （SCs） on it. Methods： The 3-D scaffolds were made by means of melt spinning, extension and weaving. The queueing discipline of the micro-channels were observed under a scanning electronic microscope （SEM）.The sizes of the micropores and the factors of porosity were also measured. Sciatic nerves were harvested from 3-day-old Sprague Dawley （SD） rats for culture of SCs. SCs were separated, purified, and then implanted on PLGA scaffolds, gelatin sponge and poly-L-lysine （PLL）-coated tissue culture poly-styrene （TCPS） were used as biomaterial and cell-supportive controls, respectively. The effect of PLGA on the adherence, proliferation and apoptosis of SCs were examined in vitro in comparison with gelatin sponge and TCPS. Results： The micro-channels arrayed in parallel manners, and the pore sizes of the channels were uniform. No significant difference was found in the activity of Schwann cells cultured on PLGA and those on TCPS （P〉0.05）, and the DNA of PLGA scaffolds was not damaged. Conclusion： The 3-D scaffolds developed in this study have excellent structure and biocompatibility, which may be taken as a novel scaffold candidate for nerve-tissue engineering.
基金National Natural Science Foundation of China,grant number:51070853Guangzhou Technology Plans,grant number:2010B103315 and 2010J-E041
文摘The objective of this paper is to design a based on composite membrane with certain mechanical porous polyvinyl alcohol （PVA） strength and biocompatibilities serving as tissue regenerative scaffolds. PVA-glycosaminoglycan （GAG）-type I collagen （COL） composite membrane was fabricated by PVA with different molecular weight （Mw） and alcoholysis degree （AD） being blended with certain amounts of GAG and COL and dried at 38~C for 24 h. The water content of the composite membranes were from 61.9% to 95.1% and swelling ratio ranged from 123.6% to 621.7%. Scanning electron micro- scope （SEM） analysis proved that PVA-GAG-COL composite membrane has porous and homogenous structure. Biocompatibility test results showed that the composite membrane was nontoxic, which could promote adhesion and proliferation of fibroblasts on the com- posite membrane. In conclusion, PVA-GAG-COL composite membrane with high water content and swelling ratio, suitable mechanical strength and good biocompatibility, has potential in tissue engineering and regenerative medicine.
