The texture evolution and mechanical properties of Cu-Ag alloys subjected to severe plastic deformation at cryogenic temperature（CT） were investigated and the sequent annealing behaviors were also studied.Compared w...The texture evolution and mechanical properties of Cu-Ag alloys subjected to severe plastic deformation at cryogenic temperature（CT） were investigated and the sequent annealing behaviors were also studied.Compared with the sheets rolled at room temperature（RT） showing copper texture,the CT-rolled sheets exhibited brass texture which indicated that cross-slip was suppressed at CT,and both the ultimate tensile strength and yield strength of the sheets were increased.Due to the in-situ recrystallization mechanism,recrystallization textures in as-annealed CT-rolled sheets were randomly distributed,while the as-annealed RT-rolled sheets mainly contained cube texture.Microstructures of the rolled and annealed sheets were observed using optical microscopy and electronic back-scatter diffraction.The results show that the dynamic recovery was suppressed during CT-rolling and resulted in higher deformation energy storage.Therefore,the recrystallization of CT-rolled sheets could start at a lower temperature than that of RT-rolled sheet at the same reduction.展开更多
WC-6MoxC-0.47Cr3C2-0.28VC binderless carbide was prepared by hot pressing （1700 °C, 20 MPa）. The sample was observed and analyzed by scanning electron microscopy, energy dispersive X–ray spectroscopy and X–ra...WC-6MoxC-0.47Cr3C2-0.28VC binderless carbide was prepared by hot pressing （1700 °C, 20 MPa）. The sample was observed and analyzed by scanning electron microscopy, energy dispersive X–ray spectroscopy and X–ray diffraction. The results show that during the hot pressing process, W atoms dissolve substantially into the MoxC crystal lattices; whilst, the reverse dissolution of Mo atoms into the WC crystal lattices takes place. Consequently, the main phase and binder phase structure are formed. The phase compositions of the main phase and binder phase are a WC-based solid solution containing Mo and a Mo2C-based solid solution containing W, respectively. The isotropic dissolution and precipitation of W and Mo atoms do not result in substantial carbide coarsening. The mechanism for the densification was discussed.展开更多
In order to improve the low ductility of the Mo-Ni alloy,Fe is added and the effects of Ni/Fe mass ratio on the densification behavior,microstructure evolution and mechanical properties of alloy were investigated.The ...In order to improve the low ductility of the Mo-Ni alloy,Fe is added and the effects of Ni/Fe mass ratio on the densification behavior,microstructure evolution and mechanical properties of alloy were investigated.The experimental results show that when iron is added to 95Mo-5Ni alloy,the formation of brittle intermetallic phaseδ-MoNi at the grain boundary is avoided.Meanwhile,the grain growth of Mo is also effectively inhibited in the sintering process.However,the addition of iron reduces the degree of densification of alloy since the activation effect of Ni is superior to that of Fe.From the experimental results,it could be concluded that the maximum hardness and bending strength are achieved by 95Mo-1.5Ni-3.5Fe alloy,which are HV 614 and 741 MPa,respectively.Combined with the analyses of bending fracture mechanism,the improvement relative to Mo-Ni alloy is likely attributed to the inhibition of the brittle phase.展开更多
The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersa...The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.展开更多
基金Project(51271046)supported by the National Natural Science Foundation of China
文摘The texture evolution and mechanical properties of Cu-Ag alloys subjected to severe plastic deformation at cryogenic temperature（CT） were investigated and the sequent annealing behaviors were also studied.Compared with the sheets rolled at room temperature（RT） showing copper texture,the CT-rolled sheets exhibited brass texture which indicated that cross-slip was suppressed at CT,and both the ultimate tensile strength and yield strength of the sheets were increased.Due to the in-situ recrystallization mechanism,recrystallization textures in as-annealed CT-rolled sheets were randomly distributed,while the as-annealed RT-rolled sheets mainly contained cube texture.Microstructures of the rolled and annealed sheets were observed using optical microscopy and electronic back-scatter diffraction.The results show that the dynamic recovery was suppressed during CT-rolling and resulted in higher deformation energy storage.Therefore,the recrystallization of CT-rolled sheets could start at a lower temperature than that of RT-rolled sheet at the same reduction.
基金Project (51074189) supported by the National Natural Science Foundation of ChinaProject (20100162110001) supported by Research Fund for the Doctoral Program of Higher Education of ChinaProject (2011BAE09B02) supported by the National Key Technology R&D Program of China
文摘WC-6MoxC-0.47Cr3C2-0.28VC binderless carbide was prepared by hot pressing （1700 °C, 20 MPa）. The sample was observed and analyzed by scanning electron microscopy, energy dispersive X–ray spectroscopy and X–ray diffraction. The results show that during the hot pressing process, W atoms dissolve substantially into the MoxC crystal lattices; whilst, the reverse dissolution of Mo atoms into the WC crystal lattices takes place. Consequently, the main phase and binder phase structure are formed. The phase compositions of the main phase and binder phase are a WC-based solid solution containing Mo and a Mo2C-based solid solution containing W, respectively. The isotropic dissolution and precipitation of W and Mo atoms do not result in substantial carbide coarsening. The mechanism for the densification was discussed.
基金Project(51734002)supported by the National Natural Science Foundation of China。
文摘In order to improve the low ductility of the Mo-Ni alloy,Fe is added and the effects of Ni/Fe mass ratio on the densification behavior,microstructure evolution and mechanical properties of alloy were investigated.The experimental results show that when iron is added to 95Mo-5Ni alloy,the formation of brittle intermetallic phaseδ-MoNi at the grain boundary is avoided.Meanwhile,the grain growth of Mo is also effectively inhibited in the sintering process.However,the addition of iron reduces the degree of densification of alloy since the activation effect of Ni is superior to that of Fe.From the experimental results,it could be concluded that the maximum hardness and bending strength are achieved by 95Mo-1.5Ni-3.5Fe alloy,which are HV 614 and 741 MPa,respectively.Combined with the analyses of bending fracture mechanism,the improvement relative to Mo-Ni alloy is likely attributed to the inhibition of the brittle phase.
基金Projects(51935014,82072084,81871498)supported by the Natural Science Foundation of ChinaProjects(20192ACB20005,2020ACB214004)supported by the Jiangxi Provincial Natural Science Foundation of China+4 种基金Project(20201BBE51012)supported by the Provincial Key R&D Projects of Jiangxi Province,ChinaProject(2018)supported by the Guangdong Province Higher Vocational Colleges&Schools Pearl River Scholar Funded Scheme,ChinaProject(2017RS3008)supported by Hunan Provincial Science and Technology Plan,ChinaProject supported by the Open Research Fund of Jiangsu Key Laboratory of Precision and Micro-Manufacturing Technology,ChinaProject(2020M682114)China Postdoctoral Science Foundation。
文摘The slow degration of iron limits its bone implant application.The solid solution of Zn in Fe is expected to accelerate the degradation.In this work,mechanical alloying(MA)was used to prepare Fe-Zn powder with supersaturated solid solution.MA significantly decreased the lamellar spacing between particles,thus reducing the diffusion distance of solution atoms.Moreover,it caused a number of crystalline defects,which further promoted the solution diffusion.Subsequently,the MA-processed powder was consolidated into Fe-Zn part by laser sintering,which involved a partial melting/rapid solidification mechanism and retained the original supersaturated solid solution.Results proved that the Fe-Zn alloy became more susceptible with a lowered corrosion potential,and thereby an accelerated corrosion rate of(0.112±0.013)mm/year.Furthermore,it also exhibited favorable cell behavior.This work highlighted the advantage of MA combined with laser sintering for the preparation of Fe-Zn implant with improved degradation performance.
