Increasing the toughness while reducing the viscosity of carbon nanotube/ polyether imide/polyether ether ketone nanocomposites

Polyether ether ketone(PEEK)has good mechanical properties.However,its high viscosity when molten limits its use because it is hard to process.PEEK nanocomposites containing both carbon nanotubes(CNTs)and polyether imide(PEI)were pre-pared by a direct wet powder blending method using a vertical injection molding machine.The addition of an optimum amount of PEI lowered the viscosity of the molten PEEK by approximately 50%while producing an increase in the toughness of the nanocom-posites,whose strain to failure increased by 129%,and fracture energy increased by 97%.The uniformly dispersed CNT/PEI powder reduced the processing difficulty of PEEK nanocomposites without affecting the thermal resistance.This improvement of the strength and viscosity of PEEK facilitate its use in the preparation of thermoplastic composites.

Improving autoencoder-based unsupervised damage detection in uncontrolled structural health monitoring under noisy conditions

Structural health monitoring is widely utilized in outdoor environments,especially under harsh conditions,which can introduce noise into the monitoring system.Therefore,designing an effective denoising strategy to enhance the performance of guided wave damage detection in noisy environments is crucial.This paper introduces a local temporal principal component analysis(PCA)reconstruction approach for denoising guided waves prior to implementing unsupervised damage detection,achieved through novel autoencoder-based reconstruction.Experimental results demonstrate that the proposed denoising method significantly enhances damage detection performance when guided waves are contaminated by noise,with SNR values ranging from 10 to-5 dB.Following the implementation of the proposed denoising approach,the AUC score can elevate from 0.65 to 0.96 when dealing with guided waves corrputed by noise at a level of-5 dB.Additionally,the paper provides guidance on selecting the appropriate number of components used in the denoising PCA reconstruction,aiding in the optimization of the damage detection in noisy conditions.

Analysis of Genetic Structure of Natural Populations of Castanopsis fargesii by RAPDs

Genetic diversity and population genetic structure in 188 individuals from five natural populations of Castampsis fargesii Franch. were studied by RAPD markers. Three hundred and eighty-five loci were identified with 41 oligonucleotide primers, out of which 157 loci were polymorphic and accounted for 40.78% of total genetic diversity at species level. Shannon's indices of diversity (I) and Nei's gene diversity ( h) were 0.459 7 and 0.296 at the species level, respectively. The result showed that genetic variation of C. fargesii populations mainly existed within populations. Genetic differentiation (Hsp-hpop)/Hsp estimated with Shannon's index of diversity and coefficient of gene differentiation (Gst) were 0.047 6 and 0.042 9 respectively, which were confirmed by the analysis of molecular variance (AMOVA). Therefore, it is apparent that within-population variation accounted for 94.97% and among-populations variation accounted for only 5.03% of the total genetic diversity. AMOVA also indicated that there was significant differentiation among populations as well as among individuals within a population.

Investigation of Mechanical Stresses for Cylinder Head of High Power Diesel Engine

Aim To ivestigate the influence on the cylinder head's stress distribution and value caused by its structure's changes.Methods Three types of cylinder heads of high power diesel engines were analysed with finite element method using I-DEAS Master series software.The actual condition of the cylinder head was simulated with different kinds of elements.Tempera- ture method was used to exert the predeformation of the bolts to the finite element model,so the pretightening force was discribed accurately Results Stress distribution regularities of the cylinder head under different working conditions were taken On the basis,the analysing results ofthreeof design schemes were compared and the optimum structure was taken Conclusion Transition condition between the head plate and the standing board ,shape of the head plate and the jobbing sheet,etc will affect the cylinder head's bearing condition

Morphological,Anatomical and Genetic Analysis for a Rice Mutant with Abnormal Hull

A mutant with abnormal hull was first discovered from a twin-seedling strain W2555 in rice （Oryza sativa L.）. The mutant had sparse branches and decreased number of florets from the base to the peak. Frequently, the florets at the top of the panicle did not develop completely. The underdeveloped florets often showed slender and white in their life cycle. Genetic analysis indicated that the mutant traits were controlled by a single recessive gene （temporarily designated as ah）. ah gene controlled the development of inflorescence meristem and the flower organ. The florets of mutant showed degenerated lemma and palea. Stamens and lodicules were homeoticly transformed into pistils and palea/lemma-like structures, respectively. It seemed that ah mutant phenotypes of the homeotic conversions in lodicules and stamens were very similar to that of the B loss-of-function spwl gene reported previously in rice.

Analysis of the Protein Structure and Function of HpaG_(Xoo)

[Objective] The study was to analyze the structure and function of HpaGXoo and the relationship between the two.[Method] Some related bioinformatics analysis software on internet such as NPSA,Swiss-Model,SAPS and InterPro Scan were adopted to analyze the structure and predict its function.[Result] HpaGXoo consists of 139 amino acids,and has many alpha-helical and coiled structure,no signal peptide on N-terminal and no transmembrane structure.It locates in bacterial cytoplasm.[Conclusion] The study will lay ...

Ultimate load bearing capacity evaluation of concrete beams subjected to freeze-thaw cycles

A theoretical prediction method based on the change of concrete material is proposed to evaluate the ultimate bending moment of concrete beams which have undergone freeze-thaw cycles （PTCs）. First, the freeze-thaw damage on concrete material is analyzed and the residual compressive strength is chosen to indicate the freeze-thaw damage. Then, the equivalent block method is employed to simplify the compressive stress-strain curve of the freeze-thaw damaged concrete and the mathematical expression for the ultimate bending moment is obtained. Comparisons of the predicted results with the test data indicate that the ultimate bending moment of concrete beams affected by FTC attack can be predicted by this proposed method. However, the bond-slip behavior and the randomness of freeze-thaw damage will affect the accuracy of the predicted results, especially when the residual compressive strength is less than 50%.

3D characterization and analysis of pore structure of packed ore particle beds based on computed tomography images

Methods and procedures of three-dimensional （3D） characterization of the pore structure features in the packed ore particle bed are focused. X-ray computed tomography was applied to deriving the cross-sectional images of specimens with single particle size of 1-2, 2-3, 3-4, 4-5, 5-6, 6-7, 7-8, 8-9, 9-10 ram. Based on the in-house developed 3D image analysis programs using Matlab, the volume porosity, pore size distribution and degree of connectivity were calculated and analyzed in detail. The results indicate that the volume porosity, the mean diameter of pores and the effective pore size （d50） increase with the increasing of particle size. Lognormal distribution or Gauss distribution is mostly suitable to model the pore size distribution. The degree of connectivity investigated on the basis of cluster-labeling algorithm also increases with increasing the particle size approximately.

Structure of the Bovine ACAD8 Gene and the Association of Its Polymorphism with the Production Traits

Acyl-coenzyme A dehydrogenases （ACAD） are a family of nuclear-coded, mitochondrial flavoenzymes that catalyze the alpha, and beta-dehydrogenation of fatty acids. The eighth member of this family, ACAD8 catalyzes the valine catabolism. In this study, the bovine ACAD8 full-length mRNA and genomic DNA sequence were obtained and its gene structure was determined through alignment of the genomic DNA sequence to the mRNA sequence. The mRNA sequence consisted of a 1,251 bp open reading frame （ORF） flanked by a 37 bp 5＇-untranslated region （UTR） and a 444 bp 3＇-UTR; and its full-length genomic DNA sequence was 13,814 bp in length and included 11 exons and 10 introns. One A-G single nucleotide polymorphism （SNP） was revealed at nucleotide 13,408 （GenBank accession No. DQ435445） in the bovine ACAD8 gene by sequencing the polymerase chain reaction （PCR） products of 6 randomly selected individuals from the sample population. Different genotypes were determined by restriction fragment length polymorphism （RFLP）. The association analysis of this SNP in bovine ACAD8 with production traits in 178 unrelated steers from 5 breeds showed that it had a significant effect on the daily gain and the beef tenderness （P〈0.05）. Cattle with the G allele grew more rapidly and the beef they produced was more tender than those with the A allele. Thus, this SNP of the bovine ACAD8 gene can be used as an indicator to improve the growth rate and the beef tenderness.

Application of the Blown-Ups Principle to Thunderstorm Forecast

Discontinuous and long-duration thunderstorm weather, which occurred at Guanghan in Sichuan Province, was analyzed and predicted using structural conversion of irregular information in phase-space from self-recording “time sequence” records for predicting rain areas, as described in the “Non Destructive Information” method proposed by Professor OuYang Shoucheng. The results show that this method can reveal important changes of weather as well as, by using irregular self-recording information recorded every ten minutes, predict local thunderstorms with durations of only half an hour, and even predict intense convections 12 hours in advance. This is significant for civil and military aviation. It shows the necessity of full utilization of information from automatic weather stations and the necessity of improvements in recording modes in current automatic stations.

Feature extraction and damage alarming using time series analysis

Aiming at the problem of on-line damage diagnosis in structural health monitoring （SHM）, an algorithm of feature extraction and damage alarming based on auto-regressive moving-average （ARMA） time series analysis is presented. The monitoring data were first modeled as ARMA models, while a principalcomponent matrix derived from the AR coefficients of these models was utilized to establish the Mahalanobisdistance criterion functions. Then, a new damage-sensitive feature index DDSF is proposed. A hypothesis test involving the t-test method is further applied to obtain a decision of damage alarming as the mean value of DDSF had significantly changed after damage. The numerical results of a three-span-girder model shows that the defined index is sensitive to subtle structural damage, and the proposed algorithm can be applied to the on-line damage alarming in SHM.

Finite element analysis of stress at implant-bone interface of dental implants with different structures

The effect of structure,elastic modulus and thickness of lower modulus layer in porous titanium implants on the stress distribution at the implant-bone interface was investigated.Three-dimensional finite element models of different titanium implants were constructed.The structures of the implants included the whole lower modulus style （No.1）,bio-mimetic style （No.2）,the whole lower modulus style in cancellous bone （No.3） and the whole dense style No.4.The stress distributions at bone-implant interface under static loading were analyzed using Ansys Workbench 10.0 software.The results indicated that the distribution of interface stress is strongly depended on the structure of the implants.The maximum stresses in cancellous bone and root region of implant No.2 are lower than those in the other three implants.A decrease in the modulus of the low modulus layer facilitates the interface stress transferring.Increasing the thickness of the low modulus layer can reduce the stress and induce a more uniform stress distribution at the interface.Among the four implants,biomimetic style implant No.2 is superior in transferring implant-bone interface stress to surrounding bones.

Analysis of Emergy Structure,Function and Efficiency of Agro-ecosystem in Hunan Province

[Objective] The aim was to explore function and efficiency of emergy input/ output of Hunan agricultural ecosystem to reveal relationship of human being with natural resources and environment. [Method] Emergy structure, function and efficien- cy of Hunan agricultural ecosystem were analyzed based on input/output data in Hunan Province in 2009 as per emergy theory. [Result] The structure characters of agricultural ecosystem were as follows： Hunan is characterized with traditional agri- culture, depending greatly on both human and animal labor. For industrial accessory emergy, chemical fertilizers make most contribution to the system, and agricultural mechanization is not satisfied. Furthermore, renewable ratio of industrial accessory emergy is lower, and development and potential of green energy is promising. In addition, prices of the products are lower, without consideration of contribution made by natural resources and environment. It also suggested that Hunan agricultural chain is short and added value of products is not high. In general, emergy output of farming and animal husbandry dominates and the prices are lower than those of forestry and fishery. The function of the system was as follows： With lower environ- mental load ratio, the system is overloaded by population and the index of sustain- able development was 5.96, suggesting that the system enjoys vitality and potential, but the economy is undeveloped and the pressure from natural resources and envi- ronment is not high. The emergy output ratio was a little lower than national level in 2009, suggesting Hunan agricultural production is extensive. [Conclusion] The re- search indicated that rapid increase of population should be controlled; surplus labor should be transferred; agricultural structure and products structure should be further adjusted; agricultural technology should be further developed; agdcultural mechaniza- tion and modernization should be improved.

Complete Sequence and Gene Organization of the Mitochondrial Genome of Tokay (Gekko gecko)

Long-PCR amplification, clone and primer-walking sequencing methods were employed in determine the complete sequence of mitochondrial genome of tokay (Gekko gecko). The genome is 16 435 bp in size, contains 13 protein-coding, 2 ribosomal and 22 transfer RNA genes. The mt genome of Gekko is similar to most of the vertebrates in gene components, order, orientation, tRNA structures, low percentage of guanine and high percentage of thymine, and skews of base GC and AT. Base A was preferred at third codon positions for protein genes is similar to amphibians and fishes rather than amnion vertebrates. The standard stop codes (TAA) present only in three protein genes, less than those of most vertebrates. Transfer RNA genes range in length from 63 to 76 nt, their planar structure present characteristic clover leaf, except for tRNA-Cys and tRNA-Ser (AGY) because of lacking the D arm.

Non-isothermal oxidation and ignition prediction of Ti-Cr alloys

The non-isothermal oxidation behavior and oxide scale microstructure of Ti-Cr alloy （0≤w（Cr）≤25%） were studied from room temperature to 1723 K by thermogravimetric analysis （TGA）, X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The influencing mechanism of chromium on the oxidation resistance of Ti-Cr alloys was discussed. The results show that the oxidation resistance of the alloys decreases with Cr below a critical chromium content wC and increases above wC; above 1000 K, the oxidation kinetics obeys parabolic rule and titanium dominates the oxidation process; after oxidation, the oxygen-diffusing layer is present in the alloy matrix, the oxide scale is mainly composed of rutile whose internal layer is rich in chromium, and chromium oxides separated out from TiO2 near the alloy-oxide interface improve the oxidation resistance. Ignition of metals and alloys is a fast non-isothermal oxidation process and the oxidation mechanism of Ti-Cr alloys during ignition is predicted.

Analysis on Fuji Apple Tree Structures and Related Factors under Different Pruning Modes

To determine the correlations between the tree structuresof Fuji apple with different pruning modes and each factor, the data about 3 tree structures which were free spindle short shoot, free spindle long shoot and slenderspindle short shoot in Xingtang County of Hebai Province were investigated, then by SPSS anal- ysis, the correlations between the taperingness and each growth factor of inserted small branch were compared. The results showed that the taperingness of central trunk of free spindle dwarf-shoot Fuji apple treeshad negative correlations with each factor of inserted small branch, while the taperingness of central trunk of free spin- dle long-shoot Fuji apple treeshad positive correlations with each factor of inserted small branch, the taperingness of central trunk of slenderspindle short-shootFuji ap- ple treeshad negative correlation with total thickness of inserted small branch, but had positive correlations with other factors. This study can provide a scientifictheo- retical basis for the pruning technology of high-density planting trees grafting by dwarfing self-rooted rootstock.

Application of laminated vierendeel truss in high-position transfer story structure

To meet the demands for large space and flexible compartmentation ofbuildings, laminated vierendeel trasses are adopted in high-position transfer story structures.First the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upperchord, middle chord, and lower chord is derived. Then combined with an actual engineering model (1:8similar ratio), the static loading and pseudo-dynamic tests of two models for laminated vierendeeltrass used in transfer story structures are conducted, in which one model adopts reinforcedconcrete, and the other adopts prestressed concrete and shape steel concrete. Seismic behaviors areanalyzed, including inter-story displacement, base shear-displacement skeleton curves, andequivalent viscosity-damping curves. A program is programmed to carry out the elasto-plastic dynamicanalysis, and displacement time-history curves of the two models are derived. The test and analysisresults show that the laminated vierendeel trass with prestressed concrete and shape steel concretehas excellent seismic behaviors. It can solve the disadvantages of laminated vierendeel trussesused in transfer story structures. Finally, some design suggestions are put forward, which can bereferenced by similar engineering.

Theoretical research on structural damage alarming of long-span bridges using wavelet packet analysis

The state equation and observation equation of the structural dynamic systems under various analysis scales are derived based on wavelet packet analysis. The time-frequency properties of structural dynamic response under various scales are further formulated. The theoretical analysis results reveal that the wavelet packet energy spectrum （WPES） obtained from wavelet packet decomposition of structural dynamic response will detect the presence of structural damage. The sensitivity analysis of the WPES to structural damage and measurement noise is also performed. The transfer properties of the structural system matrix and the observation noise under various analysis scales are formulated, which verify the damage alarming reliability using the proposed WPES with preferable damage sensitivity and noise robusticity.

Analysis on Apple Tree Structures by Free Spindle Pruning Mode

To determine the correlation between the stem taperingness and central shaft by free spindle pruning mode on different apple cultivars, the central shaft growth data of three cultivars of free spindle short shoot ＂Fuji＂, free spindle long shoot ＂Fuji＂, free spindle ＂Huaguan＂ were investigated in Xingtang County of Hebei Province by SPSS analysis. The results showed that the stem taperingness on free spindle short shoot ＂Fuji＂ was in negative correlation with central shaft, but the correlation was not significant. While the stem taperingness on free spindle long shoot ＂Fuji＂ was in positive correlation with central shaft, but the correlation was not significant either. The stern taperingness on free spindle ＂Huaguan＂ was in negative correlation with central shaft, and the correlation between the stem taperingness and the central shaft total length was significant at the level of 0.01. The results.provided scientific theoretical basis for guiding the dwarfing rootstocks close planting apple tree pruning technology.

The Formation of Colored Film on Stainless Steel and the Study for Surface Structure

This paper discusses the coloration process on the stainless steel and the properties of the film. The compositions, morphology and structure of colored films on stainless steel are studied by using SEM,AES,AFM,STM. The diffusion controlled mechanisms of films and calculation formula of surface electropotential difference are discussed.