期刊文献+
共找到4篇文章
< 1 >
每页显示 20 50 100
民用飞机结构检查可达性分析研究
1
作者 郑蓝 《民用飞机设计与研究》 2023年第2期134-138,共5页
结构检查的可达性对于航空公司的定检维修相当重要,而针对民用飞机的结构可达性分析的研究相对较少。从适航条款的要求出发,结构可达性可分为目视检查(一般目视检查和详细目视检查)任务、无损检测任务和更换、调整任务,而检查类型任务... 结构检查的可达性对于航空公司的定检维修相当重要,而针对民用飞机的结构可达性分析的研究相对较少。从适航条款的要求出发,结构可达性可分为目视检查(一般目视检查和详细目视检查)任务、无损检测任务和更换、调整任务,而检查类型任务才是可达性分析的重点。提出了一种结构检查可达性的分析方法,总结了目视检查任务和无损检测任务两种类型任务的检查要求,根据检查任务的检查要求,基于人体实体可达性、结构本体可达性、光照情况和维修资源使用情况四个角度,提出可达性检查等级,可达性检查等级结合检查任务实施的检查门槛值和检查重复间隔,给出可达性分析结论。通过某型飞机详细目视检查任务和无损检测任务的案例分析,可以看出此结构检查可达性分析方法易于操作,并可以给出明确的可达性结论,为可达性措施条款的符合提供了一种分析途径。 展开更多
关键词 结构可达性 目视检查 无损检测
下载PDF
一种飞机可达性改进模型及其应用
2
作者 王莉莉 陈云翔 +1 位作者 项华春 张诤敏 《火力与指挥控制》 CSCD 北大核心 2015年第7期92-96,共5页
针对飞机的结构可达性问题,提出了一种对飞机部件排列顺序进行优化的可达性改进方案。应用飞机的维修拆装顺序模型,得出飞机拆卸时的一般顺序,建立了基于模糊综合判定法的飞机可达性改进模型,给出了合理的飞机部件排列顺序。最后,结合实... 针对飞机的结构可达性问题,提出了一种对飞机部件排列顺序进行优化的可达性改进方案。应用飞机的维修拆装顺序模型,得出飞机拆卸时的一般顺序,建立了基于模糊综合判定法的飞机可达性改进模型,给出了合理的飞机部件排列顺序。最后,结合实例,验证了该方法的可行性和实用性。 展开更多
关键词 可达改进 结构可达性 模糊综合判定
下载PDF
Quantitative Geography Analysis on Spatial Structure of A-grade Tourist Attractions in China 被引量:5
3
作者 潘竟虎 李俊峰 从忆波 《Journal of Resources and Ecology》 CSCD 2015年第1期12-20,共9页
Tourist attraction is a very important carrier of tourism activities. A-grade tourist attraction is a national standard of comprehensive evaluation about tourist attractions quality and grade in China. In this paper, ... Tourist attraction is a very important carrier of tourism activities. A-grade tourist attraction is a national standard of comprehensive evaluation about tourist attractions quality and grade in China. In this paper, spatial structure of 2424 national A-grade tourist attractions are investigated by using GIS and quantitative analysis methods, such as nearest neighbor index (NNI), quadrat analysis, Gini coefifcient and hot spot clustering. Spatial accessibility of all A-grade tourist attractions was calculated using cost weighted distance method and ArcGIS software. Service range of each tourist attraction at 4A grade and above in China was delimitated based on the cost allocation method. Results show that China’s A-grade tourist attractions present aggregate distribution characteristics on the whole, and cultural attractions aggregate distribution is higher than of natural tourist attractions. Above-4A grade quality attractions aggregate distribution is lower than the Below-4A grade tourist attractions; cultural Above-4A grade are signiifcantly greater than the cultural Below-4A grade tourist attractions. A-grade tourist attractions in China’s eight districts are aggregate. The spatial distribution uniformity is low. Affected by the degree of economic development and tourism resources endowment, the service range of Above-4A grade attractions is big in West, smal in East, big in North, and smal in South. First-order hot spots areas were mainly concentrated in the east side of the line formed by Deqen-Alxa Left Banner. The second-order hot spot areas were composed of 11 regions, while the third-order hot spot areas include Beijing, Tianjin, Central Plains and the Yangtze River Delta. 展开更多
关键词 spatial structure spatial accessibility tourist attractions GIS China
原文传递
Structural topology optimization: Extensibility and attainability 被引量:6
4
作者 ZHANG WeiHong ZHANG ZhiDong +1 位作者 ZHU JiHong GAO Tong 《Science China(Technological Sciences)》 SCIE EI CAS 2014年第7期1310-1321,共12页
Extensibility and attainability of topology optimization are discussed by investigating a variety of simultaneous topology opti-mization methods extended from the standard formulation.First,the state of the art is hig... Extensibility and attainability of topology optimization are discussed by investigating a variety of simultaneous topology opti-mization methods extended from the standard formulation.First,the state of the art is highlighted through systematic classification of developed methods,such as simultaneous topology optimizations of microstructure and macrostructure,structure and supports,structure and design-dependent loads,structure and locations of involved components.Second,some recent results about simultaneous topology optimization of structure and applied loads are presented.It is shown that the simultaneous topology optimization is an integrated methodology that extends the concept of standard topology optimization in the sense of systematic design.The presence of more than one kind of design variable of different nature makes the optimization problem complex but enlarges the design space to attain the optimization. 展开更多
关键词 topology optimization simultaneous optimization MULTI-COMPONENT SUPPORT design-dependent load load location
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部