钻孔灌注桩施工质量事故处理

桩基施工属于隐蔽工程,一旦发生质量事故,必然对工程质量、成本、工期等造成极大影响,甚至给结构物的安全使用留下隐患。因此,对桩基的施工质量事故进行合理的处理意义重大,文章主要就该问题进行重点论述。

Elastoplastic model for discontinuous shear deformation of deep rock mass

Deep rock mass possesses some unusual properties due to high earth stress,which further result in new problems that have not been well understood and explained up to date.In order to investigate the deformation mechanism,the complete deformation process of deep rock mass,with a great emphasis on local shear deformation stage,was analyzed in detail.The quasi continuous shear deformation of the deep rock mass is described by a combination of smooth functions:the averaged distribution of the original deformation field,and the local discontinuities along the slip lines.Hence,an elasto-plastic model is established for the shear deformation process,in which the rotational displacement is taken into account as well as the translational component.Numerical analysis method was developed for case study.Deformation process of a tunnel under high earth stress was investigated for verification.

An extrusion-shear-expanding process for manufacturing AZ31 magnesium alloy tube

A new severe plastic deformation method for manufacturing tubes made of AZ31 magnesium alloy with a large diameter was developed,which is called the TCESE(tube continuous extrusion−shear−expanding)process.The process combines direct extrusion with a two-step shear−expanding process.The influences of expanding ratios,extrusion temperatures on the deformation of finite element meshes,strain evolution and flow velocity of tube blanks during the TCESE process were researched based on numerical simulations by using DEFORM-3D software.Simulation results show that the maximum expanding ratio is 3.0 in the TCESE process.The deformation of finite element meshes of tube blanks is inhomogeneous in the shear−expanding zone,and the equivalent strains increase significantly during the TCESE process of the AZ31 magnesium alloy.A extrusion temperature of 380°C and expanding ratio of 2.0 were selected as the optimized process parameters from the numerical simulation results.The average grain size of tubes fabricated by the TCESE process is approximately 10μm.The TCESE process can refine grains of magnesium alloy tubes with the occurrence of dynamic recrystallization.The(0001)basal texture intensities of the magnesium alloy tube blanks decrease due to continuous plastic deformation during the TCESE process.The average hardness of the extruded tubes is approximately HV 75,which is obviously improved.

Effect of casting speed on floating grains and macrosegregation ofdirect-chill cast 2024 alloy with intensive melt shearing

The ingot was prepared by direct-chill(DC)casting technology with different casting speeds under the influence of intensive melt shearing to explore the effect of casting speed and intensive melt shearing on the floating grains and negative centerline segregation.The results indicate that the application of intensive melt shearing in DC casting process can distribute the floating grains uniformly,reduce the area fraction of the floating grains,alleviate the negative centerline segregation,and improve the uniformity of temperature field in the sump.It is also suggested that under the influence of intensive melt shearing,the casting speed plays a crucial role in the amounts and distribution of floating grains.At low casting speed,the intensive melt shearing can significantly reduce the area fraction of the floating grains and distribute them uniformly throughout the ingot.However,this effect gradually disappears with the increase of casting speed.

Rapid pressure-assisted sinter bonding in air using 200 nm Cu particles and enhancement of bonding strength by successive pressureless annealing

To design an effective and realistically applicable sinter bonding process for power devices,we proposed a two-step process using a 200 nm Cu-particle-based paste to form a bondline having high-temperature sustainability and superior thermal conductance.This process involved rapid pressure-assisted sinter bonding in air followed by pressureless annealing in a nitrogen atmosphere.In the case of a paste prepared with a mixture of 20 wt.%malic acid and 80 wt.%ethylene glycol,sinter bonding at 300℃and 5 MPa for only 30 s resulted in a sufficient shear strength of 23.1 MPa.The shear strength was significantly enhanced to 69.6 MPa by the additional pressureless aging for 30 min.Therefore,the two-step sinter bonding process is expected to provide an outstanding production rate as a next-generation sinter bonding process.

Experimental Investigation of Dimensionless Velocity and Shearing Stress in Boundary Layer Flow on Continuous Moving Surface in Power Law Fluids

An analysis is carried out to study the steady flow characteristics from a continuous flat surface moving in a parallel free stream of non-Newtonian power law fluid. The constitutive equations of the fluid are transformed into dimensionless ones. The velocity field is measured by Particle Image Velocimetry. Experimental results are obtained for the distribution of velocity. The influence of wall velocity ratio parameter on boundary layer flow field is observed in the experiment. Dimensionless velocity distribution and shearing stress distribution are obtained by post-processing experimental results. The effects of various physical parameters like velocity ratio parameter and similarity variable on various momentum transfer characteristics are discussed in detail and shown graphically. It is indicated that dimensionless velocity increases with velocity ratio parameter and similarity variable, and that dimensionless shearing stress decreases with velocity ratio parameter and similarity variable.

Combined torsional buckling of double-walled carbon nanotubes with axial load in the multi-field coupled condition

The present study has theoretically investigated the combined torsional buckling of double-walled carbon nanotubes (DWCNTs) with axial load in the multi-field coupled condition. The effects of torsion, axial load, thermal-electrical change, surrounding elastic medium and the Van der Waals forces are all taken into consideration. The governing equation of buckling for CNTs subjected to thermo-electro-mechanical loadings has been established based on an elastic shell model of continuum mechanics. Reasonable simplifications are made to get the explicit expression of the critical buckling shear stress of DWCNTs, and numerical experiments are conducted for further research. It is shown that under certain electric and temperature field the critical buckling shear stress of DWCNTs only depends on the wave number of buckling modes. On the other hand, all the related impact factors have enormous influence on the critical buckling shear stress under a certain buckling mode. The critical buckling shear stress changes linearly with the axial-to-shear stress ratio, as well as the thermal and electric change. Axial compression tends to make DWCNTs unstable, while axial tension benefits the buckling stability. The critical buckling shear stress is directly proportional to the applied voltage. At room or lower temperature, the critical shear stress for infinitesimal buckling increases as the temperature change increases, while it decreases at a higher temperature. The conclusions are useful for the design of nano-structures related to the buckling stability of DWCNTs.