Comprehensive Prevention and Control Technologies of Rice Blast in Disease Nanchong City

The study was conducted to reduce blast damage, the use of pesticides residue, environment pollution and control costs, and to make a significant contribution to the improvement of grain production, quality and agriculture ecological environment. Over these years, by the methods of systematical monitoring, regular surveys, field investigation, rice blast resistance identification, experiments and meteorological data analysis, the study on comprehensive prevention and control of rice blast in Nanchong City was conducted. The results showed that the rice varieties more sensitive to blast had a higher incidence of severe blast disease. Replacing,varieties with different source of resistance every three to five years and reasonable variety distribution can effectively reduce the prevalence of rice blast. Appropriate treatment of infected rice straw and pathogen, seed disinfection, seedling disinfection, and pesticide application at transplanting and etc. can delay blast occurrence and reduce the damage caused by blast. By analyzing the blast control efficiency of pesticides applied at different growth stages, we found that best control efficiency against blast was achieved by spraying pesticide twice during the whole growth stage, once 3 d before transplanting or 10 d after transplanting; and once at initial heading stage. Spraying 525 g/hm^2 75% tricyclazole was proven to be the best dosage for blast control. However, 375-450 g/hm^2 75% tricyclazole is enough if the blast incidence is not severe, or the rice varieties are slightly susceptible to blast.The control efficiency against leaf blast between 4% kasugamycin and 20% tricyclazole had no significant difference, but was significantly higher than that of 100 billion spores/g of Bacillus subtilis. The control efficiency against neck blast had no significant difference among 4% kasugamycin, 20% tricyclazole and 100 billion spores/g of B. subtilis. 450 g/hm^2 75% tricyclazole had better control efficiency against neck blast than 2 250 g/hm^2 2% 800 million spores/g Jinggangmycin-wax bud bacteria SC, 1 050 g/hm^2 41% kasugamycin-isoprothiolane WP and 900 g/hm^2 41%kasugamycin-isoprothiolane WP. The frequency of severe blast incidence in Nanchong City has reached 50% since 1997. The rice blast disease has been effectively controlled by comprehensive prevention and control technology, reducing the production loss to less than 2%, and pesticides by 4 523 t in total. In 2014, 327000 t rice grains were approved as pollution-free, green and organic agricultural products, indicating that the blast control measures produced great economic, social and ecological values.

Review of prediction techniques on hydrodynamic impact of ships

This paper presents the survey and assessment of the estimation techniques on hydrodynamic impact. The description and definition of hydrodynamic impact are presented, and the categorization of prediction techniques and the difficulties are discussed. Analysis theories and numerical simulation techniques are reviewed and the characteristics of those theories and approaches are analyzed. The efforts are made to pinpoint the advantages and disadvantages. Recommendations for further research and development are made.

On the Comprehensive Prevention and Control Technology of the Reproductive Organ Disease of Breeding Geese under the Anti-season Breeding Mode

Reproductive organ disease of geese is an endemic and multiple infectious disease in large-scale breeding of breeding geese, especially in anti-season production, which brings a great economic loss to goose production. To make effective prevention and control of reproductive organ disease of breeding geese under the anti-season breeding mode, the characteristics of control principles of infectious diseases of the poultry and the occurrence and prevalence of reproductive organ disease must be combined, so as to carry out scientific prevention and control.At the same time, according to the climate characteristics of summer, the feeding and management of breeding geese and water quality control should also be done well, and many corresponding measures should also be taken, thus obtaining better effect.

任务型教学在高中英语教学中的尝试与体会

“教师应避免传授语言知识的教学方法，尽量采用‘任务型’的教学途径……教师应依据课程的总体目标，并结合教学内容，创造性地设计贴近学生实际的教学活动，吸引和组织他们积极参与。学生通过思考，调查，讨论，交流和合作等方式，学习和使用英语，完成学习任务。”……

A NOVEL AERONAUTICAL STATIC INVERTER WITH HIGH FREQUENCY PULSE DC LINK

A new combined soft switching technique and a novel topology of aeronautical static inverter with high frequency pulse dc link are proposed in this paper, namely an electrical isolated converter can realize soft switching of two stage cascade converters. It lays technical foundation for high power density, high efficiency and low cost aeronautical static inverter. The operation and design approach of this topology are carefully analyzed and studied. The validity of this topology is verified by simulation and test.

Technical Regulations for Comprehensive Control Weeding in Millet Field

According to experiments in many years in Hebei Province, the research explored weed comprehensive control technology on millet fields in terms of application range, prevention rules, prevention object, agricultural control, physical control, and chemical control and proposed specific methods and technological indices in order to provide technological references for comprehensive control on weeds of millet fields.

Reactor Network Synthesis for Waste Reduction Using Instantaneous Value of Environmental Index

Waste reduction is gaining importance as the preferred means of pollution prevention. Reactor network synthesis is one of the key parts of chemical process synthesis. In this study, a geometric approach to reactor network synthesis for waste reduction is presented. The bases of the approach are potential environment impact （PEI） rate-law expression, PEI balance and the instantaneous value of environmental indexes. The instantaneous value can be derived using the PEI balance, PEI rate-law expression and the environmental indexes. The optimal reactor networks with the minimum generation of potential environment impact are geometrically derived by comparing with areas of the corresponding regions. From the case study involving complex reactions, the approach does not involve solving the complicated mathematical problem and can avoid the dimension limitation in the attainable region approach.

Property Identification of Anomalous Seismic Bodies by GMES Techniques, A Case History

What are the anomalous seismic reflection bodies at depths of over 6000m？Are they reefs or igneous rock？This is a difficult problem for seismic techniques,but the GMES technique can handle it .The GMES technique is a joint exploration technique combining gravity,magnetic,electrical,and seismic techniques.The specific procedure is to conduct a 2D interface-constrained CEMP inversion using 2D seismic and log data followed by a property parameter inversion of the anomalous bodics using gravity and seismic data by the stripping technique.We then estimate the physical properties ofthe anomalous bodies,such as density,susceptibility,resistivity,velocity,and etc.to deduce the geological features of the bodies and provide a basis for drilling decisions.The work in the TZ area reported in this paper shows the applicability of the technique.

Void fill techniques for stabilizing roof conditions during longwall recovery

It has been proven that longwall faces can be moved safely and efficiently. However,abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania,roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique,engineering solution was developed that utilized a modified concrete material to fill the voids,creating stability in the affected area. The many phases of this project included the construction phase,void pumping,cutting out,and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions,making it possible for the mine operator to safely complete the longwall move.

Energy and Water Optimization in Biofuel Plants

In this paper we address the topic of energy and water optimization in the production of bioethanol from corn and switchgrass. We show that in order for these manufacturing processes to be attractive,there is a need to go beyond traditional heat integration and water recycling techniques. Thus,we propose a strategy based on mathe-matical programming techniques to model and optimize the structure of the processes,and perform heat integration including the use of multi-effect distillation columns and integrated water networks to show that the energy effi-ciency and water consumption in bioethanol plants can be significantly improved. Specifically,under some circum-stances energy can even be produced and the water consumption can be reduced below the values required for the production of gasoline.

Suitable retention and recovery technology of floor coal at ends of fully mechanized face with great mining heights

Gateways at faces of great mining heights are mostly driven along the roof of coal seams.For gateway height restrictions,a 1-3 m floor coal is retained,leaving a triangular floor coal at the face ends,causing a loss of coal.In order to improve coal recovery rates and to ensure efficiency of equipment at coal mining faces,we investigated suitable retention methods and recovery technology of floor coal at face ends.The upper floor coal can directly be recovered by a shearer with floor dinting.The lower floor coal is recovered by shearer with floor dinting after advanced floor dinting and retaining a step for protecting coal sides in a haulage gateway.Field practice shows that this method can improve the coal recovery rates at fully mechanized working faces with great mining heights.

CLINICAL OBSERVATION ON THE TREATMENT OF CHRONIC FATIGUE SYNDROME WITH DEEPLY PUNCTURED ELONGATED NEEDLE COMBINED WITH COMPREHENSIVE NURSING

Objective： To observe the therapeutic effect of deep puncture of Zusanli （足三里 ST 36） and Qihai （气海 CV 6） with elongated needle combined with comprehensive nursing in the treatment of chronic fatigue syndrome （CFS） so as to provide new way and effective method for CFS. Methods： A total of 100 cases of CFS patients were evenly randomized into treatment group and control group which were treated with elongated needle puncture of ST 36 and CV 6 plus nursing and oral ackninistration of Shiquan Dobu Tong （十全大补汤 Decoction of Ten Powerful Tonics） separately. Acupuncture and medication were given once daily, with 7 sessions being a therapeutic course, 4 courses altogether. Results： After 4 courses of treatment, of the two 50 cases in treatment and control groups, 4 （8.0%） and 2 （4.0%） were cured, 37 （74.0%） and 16 （32.0%） experienced marked im- provernent, 6 （ 12.0 % ） and 19 （38.0 % ） had improvement, 3 （6.0 % ） and 13 （26.0 % ） tailed, with the total effective rates being 94.0% （47/50） and 74.0% （37/50） respectively. The total effective rate and markedly effective rate of treatment group were significantly higher than those of control group （P〈0.05, 0.01）. Conclusion; Deep puncture of Zusenli （ST 36） and Qihai （CV 6） with elongated needle combined with comprehensive nursing has a definite therapeutic effect in the treatment of chronic fatigue syndrome.

Underground mining of thick coal seams

This paper reviews underground mining methods for total thickness of a thick coal seam in single lift （TI＇rCSSL）. Review shows the required engineering for extraction of thick seams needs to be fitted with thickness of the seam, behavior of rock-mass and surrounding stress conditions for efficient mining. Variants of TI＇rCSSL are able to extract a maximum 10-12 m thickness only. An improvement in bending moment of the overlying coal band in longwall top coal caving （LTCC） provides better under-winning opportunity for the roof coal band. An acceptable limit of 25 MPa compressive strength of coal for the success of LTCC may be increased under favorable geo-technical conditions. Bord and pillar in India adopted induced caving of roof coal band for single lift depillaring of total thickness （SLDTr） of a compe- tent thick coal seam developed along floor. Case studies are given to arrest the adverse effects of extrac- tion height on pillars.

Factors that Affect Pellet Quality： A Review

Pelleting is the most popular thermal processing technique in poultry industry. Birds fed pelleted diets have greater feed intake and weight gain, and better feed conversion ratio. However, this better performance can only be achieved, if the pellets remain intact until they are ingested by the birds. Many factors may affect pellet physical quality, such as feed nutritional composition, ingredient particle size, conditioning temperature and time, feed moisture, etc.. Despite their importance, sometimes these factors are not managed properly, therefore, pelleted feed may not contain a high amount of intact pellets. In addition, the possible interactions among these variables may yield different responses in comparison with those expected when individual factors are considered. Very few experiments have been conducted to evaluate the impact of combined factors on pellet quality. This may be explained by the presence of many qualitative and quantitative factors in the manufacturing process. Research indicates that heat processing and feed formulation, especially fat inclusion level, are the factors which have the biggest influence on pellet quality. Strategies, such as the expansion process and fat inclusion restriction or post pellet liquid fat application could be implemented to produce high physical quality pellets. More research is needed to identify which factors have a positive or negative effect on pelleting process and to find new strategies to improve pellet physical quality.

Evaluation of mine scale longwall top coal caving parameters using continuum analysis

A mine-scale analysis of Longwall Top Coal Caving (LTCC) is performed using a continuum mechanics finite element solver called COSFLOW. The uniqueness of COSFLOW is that it incorporates Cosserat continuum theory in its formulation for describing the load deformation of bedded rocks. It is shown that such a continuum based code is valuable for assessing the feasibility of introducing LTCC in any mine. Various LTCC parameters, for example chock convergences, top coal failure behavior, strata cavingmechanism, abutment stresses and vertical stresses, were evaluated for a mine using COSFLOW.

A Technical Review of Hydro-Project Development in China

This paper summarizes the development of hydro-projects in China,blended with an international perspective.It expounds major technical progress toward ensuring the safe construction of high dams and river harnessing,and covers the theorization of uneven non-equilibrium sediment transport,inter-basin water diversion,giant hydro-generator units,pumped storage power stations,underground caverns,ecological protection,and so on.

Deformation mechanism of surrounding rocks and key control technology for a roadway driven along goaf in fully mechanized top-coal caving face

The variation of the stress in the bolted surrounding rocks structure of the roadway driven along goaf in a fully mechanized top coal caving face with moderate stable conditions are studied by using numerical calculation. The essential deformation characteristics of the surrounding rocks in this kind of roadway are obtained and the key technology of bolting support used under these conditions is put forward.

Study on destressing technology for a roadway driven along goaf in a fully mechanized top-coal caving face

Based on the deformation characteristics of the roadways driven along goaf in fully mechanized top coal caving faces, the author considers that it is the key to ensure the stability of surrounding rocks of roadway driven along goaf to control the deformation during the period affected by mining. Considering the characteristics of the roadway layout in fully mechanized top coal caving faces, a technical scheme of destressing is put forward and the destressing effect is analyzed by using the software of Universal Distinct Element Code 3 0(UDEC 3 0).

Survey on Key Technology Development and Application in Trusted Computing

Trusted computing,which can effectively increase the credibility of information system,has made great achievements and is in continuous development. For country who is going to strengthen network construction like China,it is an important fundamental supporting technology worth researching. China is in the international forefront in the field of trusted computing. This paper gives comprehensive introductions to the new development and application of key technologies in trusted computing,such as various trusted platform modules(TPM、TCM、TPCM),TCG Software Stack(TSS),trusted cloud server and Trusted Execution Environment(TEE). We illustrate the progressing and application extension of these technologies and also point out some key problems worth studying in the future.

Study on comprehensive gas control techniques and practice in coal mines

The origins and main control methods of gas in coal seams were introduced cursorily, and the processes that need to be done in controlling gas, which includes prediction of gas emissions, drainage systems, the means of prevention of gas outbursts, and some suggestions were put forward. The characteristic of different gas emissions and the corresponding counter measures were presented, and ＆ case study of simultaneous extraction of coal and gas in Xieyi Coal Mine was carried out by coal mining and gas extraction without coal-pillar. The field application shows that gas drainage ratio in panel 5121（0） averages about 90% and reaches as high as 95~/0, which will give beneficial references to gas control in coal mines.