It is common to assume that structures are designed in view of 50 year life cycle as per Euro-Code 2 and other codes. In special cases, structures are designed in view of longer life cycle, such as bridges, important ...It is common to assume that structures are designed in view of 50 year life cycle as per Euro-Code 2 and other codes. In special cases, structures are designed in view of longer life cycle, such as bridges, important infrastructure facilities, important religious structures or in case of extended returning period of seismic event or floods. Beside issues of durability and maintenance aspects, this involves also the need to cover the probability of exceeding characteristic design live loads during the extended period, while keeping the same levels of the accepted risk that were assumed by the various codes, as good enough for the standard 50 year life cycle. Bearing in mind that design procedures, formulations, materials characteristic strengths and partial safety factors are used for these structures as per the existing codes, scaling of partial safety factors, or alternatively an additional ＂compensating＂ factor is required. A simplified approach and procedure to arrive at a reasonable calibration of the code safety factors based on 50 years to compensate for an extended life cycle, based upon structural reliability considerations, is proposed.展开更多
This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank ...This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank angle degree(CAD)before top dead center(BTDC)and a set of constant ignition timing tests while also keeping the 10℃AD BTDC injection and adding ignition improver(2-ethylhexylnitrate-,2-EHN)to the fuel mixtures.Soot particles were characterized using DMS-500 instrument in terms of mass,size,and number.The experimental results showed that adding 2-EHN to the model fuel blends reduced the soot surface area,soot mass concentration and soot mean size.Replacing 20 vol%of a C 7-heptane with 20 vol%methyl-decanoate(an oxygenated C 11 molecule)did not affect the ignition delay or rate of fuel air premixing,the peak in-cylinder pressure or heat release rates.Toluene addition(0−22.5 vol%)to heptane increased the mean size of the soot particles generated by only 3%while also resulted in a slight increase in the peak cylinder pressure and peak heat release rates.Blending toluene and methyl-decanoate into heptane without adding 2-EHN increased the premix phase fraction by at least 13%.However,by adding 2-EHN(4×10^(−4)−1.5×10^(−3)),the premixed phase fraction decreased by at least 11%.展开更多
Poly(styrene-glycidyl methacrylate) particles having bowl-shaped hollow structures were synthesized by swollen seed emulsion polymerization. The PS emulsion synthesized through soap-free emulsion polymerization was sw...Poly(styrene-glycidyl methacrylate) particles having bowl-shaped hollow structures were synthesized by swollen seed emulsion polymerization. The PS emulsion synthesized through soap-free emulsion polymerization was swollen by toluene, and then the mixture of second monomers was added under polymerization condition. So a thin shell of poly(styrene-glycidyl methacrylate) cross-linked by triethylene glycol diacrylate was formed around the swollen PS particle. The bowl-shaped particles were obtained after the collapsing of the thin shell when the toluene emanated from the particles, but the shapes were effected by the degrees of cross-linking. The shape of the particles was observed by SEM. The release behavior of solvent from the particles was examined by TG.展开更多
In this paper,a modeling method for a pantograph-catenary system is put forward to investigate the dynamic contact behavior in space,taking into consideration of the appearance characteristics of the contact surfaces ...In this paper,a modeling method for a pantograph-catenary system is put forward to investigate the dynamic contact behavior in space,taking into consideration of the appearance characteristics of the contact surfaces of the pantograph and catenary.The dynamic performance of the pantograph-catenary system,including contact forces,accelerations,and the corresponding spectra,is analyzed.Furthermore,with the modeling method,the influences of contact wire irregularity and the vibration caused by the front pantograph on the rear pantograph for a pantograph-catenary system with double pantographs are investigated.The results show that the appearance characteristics of the contact surfaces play an important role in the dynamic contact behavior.The appearance characteristics should be considered to reasonably evaluate the dynamic performance of the pantograph-catenary system.展开更多
文摘It is common to assume that structures are designed in view of 50 year life cycle as per Euro-Code 2 and other codes. In special cases, structures are designed in view of longer life cycle, such as bridges, important infrastructure facilities, important religious structures or in case of extended returning period of seismic event or floods. Beside issues of durability and maintenance aspects, this involves also the need to cover the probability of exceeding characteristic design live loads during the extended period, while keeping the same levels of the accepted risk that were assumed by the various codes, as good enough for the standard 50 year life cycle. Bearing in mind that design procedures, formulations, materials characteristic strengths and partial safety factors are used for these structures as per the existing codes, scaling of partial safety factors, or alternatively an additional ＂compensating＂ factor is required. A simplified approach and procedure to arrive at a reasonable calibration of the code safety factors based on 50 years to compensate for an extended life cycle, based upon structural reliability considerations, is proposed.
文摘This paper examines the effect of equalizing ignition delay in a compression ignition engine.Two sets of tests were conducted,i.e.a set of constant injection timing tests with start of fuel injection at 10°crank angle degree(CAD)before top dead center(BTDC)and a set of constant ignition timing tests while also keeping the 10℃AD BTDC injection and adding ignition improver(2-ethylhexylnitrate-,2-EHN)to the fuel mixtures.Soot particles were characterized using DMS-500 instrument in terms of mass,size,and number.The experimental results showed that adding 2-EHN to the model fuel blends reduced the soot surface area,soot mass concentration and soot mean size.Replacing 20 vol%of a C 7-heptane with 20 vol%methyl-decanoate(an oxygenated C 11 molecule)did not affect the ignition delay or rate of fuel air premixing,the peak in-cylinder pressure or heat release rates.Toluene addition(0−22.5 vol%)to heptane increased the mean size of the soot particles generated by only 3%while also resulted in a slight increase in the peak cylinder pressure and peak heat release rates.Blending toluene and methyl-decanoate into heptane without adding 2-EHN increased the premix phase fraction by at least 13%.However,by adding 2-EHN(4×10^(−4)−1.5×10^(−3)),the premixed phase fraction decreased by at least 11%.
文摘Poly(styrene-glycidyl methacrylate) particles having bowl-shaped hollow structures were synthesized by swollen seed emulsion polymerization. The PS emulsion synthesized through soap-free emulsion polymerization was swollen by toluene, and then the mixture of second monomers was added under polymerization condition. So a thin shell of poly(styrene-glycidyl methacrylate) cross-linked by triethylene glycol diacrylate was formed around the swollen PS particle. The bowl-shaped particles were obtained after the collapsing of the thin shell when the toluene emanated from the particles, but the shapes were effected by the degrees of cross-linking. The shape of the particles was observed by SEM. The release behavior of solvent from the particles was examined by TG.
基金Project supported by the National Natural Science Foundation of China (No.51075341)the National Basic Research Program (973) of China (No.2011CB711105)
文摘In this paper,a modeling method for a pantograph-catenary system is put forward to investigate the dynamic contact behavior in space,taking into consideration of the appearance characteristics of the contact surfaces of the pantograph and catenary.The dynamic performance of the pantograph-catenary system,including contact forces,accelerations,and the corresponding spectra,is analyzed.Furthermore,with the modeling method,the influences of contact wire irregularity and the vibration caused by the front pantograph on the rear pantograph for a pantograph-catenary system with double pantographs are investigated.The results show that the appearance characteristics of the contact surfaces play an important role in the dynamic contact behavior.The appearance characteristics should be considered to reasonably evaluate the dynamic performance of the pantograph-catenary system.
