“合作开发耐腐合金长寿命免维护蓄电池”项目通过科技部验收

近日，经化学、材料、化工和国际合作管理领域专家的审核，国际科技合作重点项目计划项目“合作开发耐腐合金长寿命免维护蓄电池”通过验收。

硼砂-对苯二甲酸电解液中AZ91D镁合金的阳极氧化处理(英文)

研究了硼砂-对苯二甲酸环保型电解液中AZ91D镁合金的阳极氧化.考察了对苯二甲酸对镁合金阳极氧化过程及其氧化膜性能的影响,并利用扫描电镜(SEM)、X射线衍射(XRD)、能量散射谱(EDS)、动电化极化和电化学交流阻抗谱(EIS)等进行了分析表征.结果表明,对苯二甲酸的浓度对阳极氧化成膜过程、氧化膜的表面形貌、厚度、相结构和耐腐蚀性能都有重要影响.在硼酸盐电解液中加入适量的对苯二甲酸后,氧化电流密度降低,过度放电现象受到了明显的抑制,所制得的阳极氧化膜的质量也有了显著改善.氧化膜表面变得光滑、致密,膜厚度略有降低.氧化膜与镁合金基底的结合更紧密,而且其耐腐蚀性能也得到了明显增强.该研究对于镁合金阳极氧化处理工艺的环保化及阳极氧化膜质量的提高都具有积极意义.

Effects of ultrasonic vibration on solidification structure and properties of Mg-8Li-3Al alloy

Ultrasonic vibration was introduced into the Mg-8Li-3A1 alloy melt during its solidification process. The microstructure, corrosion resistance and mechanical properties of the Mg-8Li-3A1 alloy under ultrasonic vibration were investigated. The experiment results show that the morphology of a phase is modified from coarse rosette-like structure to fine globular one with the application of ultrasonic vibration. The fine globular structure is obtained especially when the power is 170 W, and the refining effect also gets better with prolonging the ultrasonic treatment time. The corrosion resistance of the alloy with 170 W of ultrasonic vibration for 90 s is improved apparently compared with the alloy without ultrasonic vibration. The mechanical properties of alloys with ultrasonic vibration are also both improved apparently. The tensile strength and elongation of alloy improve by 9.5% and 45.7%, respectively, with 170 W of ultrasonic treatment for 90 s.

Electrochemical corrosion properties of Zr- and Ti-based bulk metallic glasses

The corrosion behaviors of Ti-based and Zr-based amorphous alloys and their corresponding crystallized alloys were studied by electrochemical methods. It is found that the corrosion potentials of Zr-based amorphous alloy and its corresponding crystalline counterpart are both lower than those of the Ti-based amorphous alloy in the 1 mol/L H2SO4 solution. In the 3.5% NaCl solution,Zr-based crystallized alloy exhibits the lowest corrosion potential among the experimental samples. No passivation is observed in the corrosion process for the Zr-based crystalline alloy. However, Zr- and Ti-based amorphous alloys both exhibit passivation characteristics. EIS measurements indicate the amorphous alloys exhibit better corrosion resistance than the crystallized one in the NaCl solution. Surface analysis shows that both amorphous alloys in the NaCl solution are eroded by pitting corrosion. In the H2SO4 solution, all the alloys display similar behaviors and their surfaces can mostly keep intact except for some cracks on the corroded surface at local region.

High corrosion resistance of electroless Ni-P with chromium-free conversion pre-treatments on AZ91D magnesium alloy

Phosphate-manganese, tannic acid and vanadium conversion coatings were proposed as an effective pre-treatment layer between electroless Ni-P coating and AZ91D magnesium alloy substrate to replace the traditional chromate plus HF pre-treatment. The electrochemical results show that the chrome-free coatings plus electroless Ni-P coating on the magnesium alloy has the lowest corrosion current density and most positive corrosion potential compared with chromate plus electroless Ni-P coating on the magnesium alloy. These proposed pre-treatment layers on the substrate reduce the corrosion of magnesium during plating process, and reduce the potential difference between the matrix and the second phase. Thus, an electroless Ni-P coating with fine crystalline and dense structure was obtained, with preferential phosphorus content, low porosity, good corrosion-resistance and strengthened adhesion than the chromate plus electroless Ni-P.

Tribological and corrosion behavior of PEO coatings with graphite nanoparticles on AZ91 and AZ80 magnesium alloys

The effect of the addition of graphite nanoparticles into the electrolyte used to produce plasma electrolytic oxidation（PEO） coatings on AZ91 and AZ80 magnesium alloys was studied. The corrosion and wear resistances of the obtained coatings were investigated. A solution that contained both phosphates and silicates was used as electrolyte. Moreover, two different PEO treatment times were studied. The corrosion resistance was analyzed with potentiodynamic polarization and EIS tests; the wear resistance was investigated with a flat on ring tribometer. The results were related to the morphology, microstructure, elemental composition and thickness evaluated with SEM analysis. The presence of the graphite nanoparticles increased the thickness, produced a densification of the coating and sealed the pores on the surface, thus improving both the corrosion and wear resistance. The increase in the corrosion and wear resistances was more evident for AZ91 than for AZ80 due to the higher aluminum content.

Influence of heat treatment on corrosion behavior of hot rolled Mg5Gd alloys

The influence of heat treatment on the corrosion behavior of rolled Mg5 Gd alloys in 3.5 wt.% Na Cl solution saturated with Mg(OH)2 was characterized by immersion test, electrochemical test, scanning electrochemical microscopy(SECM) and corrosion morphology analysis in order to improve the corrosion resistance of Mg alloys. The results showed that solution treatment reduced the corrosion rate of the Mg5 Gd significantly, resulting in relatively uniform corrosion and shallow corrosion cavities due to the dissolution of Cd-containing particles. The following aging process could further decrease the corrosion rate. Precipitation of nano-sized Cd-containing particles did not cause apparent micro-galvanic corrosion, which could be attributed to the formation of a protective corrosion product film fully covering the particles.

Enhancing mechanical properties and corrosion performance of AA6063 aluminum alloys through constrained groove pressing technique

The use of a constrained groove pressing(CGP) method to plastically deform AA6063 aluminum alloy led to the improved surface properties. It was found that hardness magnitude is dramatically improved and its uniformity is considerably decreased after the first pass, while subsequent passes result in better hardness behavior for the processed material. Also, the elongated grains formed in the first pass of the CGP are gradually converted to the equiaxed counterparts by adding pass numbers. Eventually, higher corrosion resistance of the sample by imposing the CGP process is related to the quick formation of passivation film and the change in the morphology of the second phase and precipitates which hinder their electrochemical reactions and decrease the potential localized attack sites.

Effects of sealing process on corrosion resistance and roughness of anodic films of titanium alloy Ti-10V-2Fe-3Al

Anodic oxide films of titanium alloy Ti-10V-2Fe-3Al were sealed in calcium acetate solution. The morphology and composition of the sealed films were investigated using scanning electron microscopy (SEM), atomic force microscope (AFM) and energy dispersive spectroscopy (EDS). The results show that the sealing process makes the anodic oxide films more uniform. Elemental calcium is presented through the whole depth of the anodic oxide films. The roughness of the anodic oxide films is reduced after the sealing process. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization were used to study the corrosion behavior of the anodic oxide films. It is revealed that the sealing process improves the corrosion resistance of the anodic oxide film of titanium alloy Ti-10V-2Fe-3Al.

TiC strengthened CoCrNi medium entropy alloy:Dissolution and precipitation of TiC and its effect on microstructure and performance

In order to improve the strength and corrosion resistance of CoCrNi medium entropy alloy,TiC strengthened CoCrNi medium entropy alloy(CoCrNi/(TiC)_(x)(x=0.1,0.2,0.4))was designed by addition of different amounts of TiC.The effects of TiC content on the microstructure,mechanical properties,and corrosion resistance of the alloy were investigated.It was found that the precipitation morphologies of TiC changed from lamellar eutectic to needle structure with the increase of TiC content,and finally formed mixed needled and bulk TiC particles.TiC appears as a dissolution−precipitation phenomenon in the CoCrNi alloy,which is important for the mechanical properties and corrosion resistance of the CoCrNi/(TiC)_(x) alloy.The strength of alloy was enhanced obviously after the addition of TiC.The compressive yield strength of CoCrNi/(TiC)_(0.4) alloy reached 746 MPa,much larger than that of the CoCrNi medium entropy alloy,108 MPa.Additionally,the addition of TiC was found to improve the corrosion resistance of CoCrNi medium entropy alloy in the salt solution.

Zinc-doped hydroxyapatite-zeolite/polycaprolactone composites coating on magnesium substrate for enhancing in-vitro corrosion and antibacterial performance

This work is focused on developing zinc-doped hydroxyapatite-zeolite(Zn HA-Zeo)and polycaprolactone(PCL)composite coatings on magnesium(Mg)substrate to improve the corrosion resistance and antimicrobial properties.Dip-coating technique was used to coat Zn HA-Zeo/PCL on the Mg substrate at room temperature.The samples were subjected to field emission scanning electron microscopy(FESEM),X-ray diffraction(XRD),Fourier transform infrared(FTIR),energy dispersive X-ray spectroscopy(EDX)and antimicrobial potential.Results demonstrated that composite coatings consist of HA,scholzite,zeolite,and PCL phases.EDX spectra indicated the presence of calcium(Ca),silicon(Si),aluminum(Al),zinc(Zn),phosphorus(P)and oxygen(O).The composite surface appeared in spherical-like microstructure on coating with thickness ranging 226-260μm.Zinc-doped HA-Zeo composite coating had a high corrosion resistance and provided sufficient protection to the Mg surface against galvanic corrosion.Doped Zn HA-Zeo coating samples exhibited superior disc inhibition by confirming antimicrobial activity against the E.coli as compared to HA-Zeo sample.Altogether these results showed that the Zn HA-Zeo coatings not only improved the corrosion resistance,but also enhanced the antimicrobial property and hence they can be used as suitable candidates for implant applications.

Role of Ni content in improvement of corrosion resistance of Zn-Ni alloy in 3.5% Na Cl solution. Part I: Polarization and impedance studies

Zn plays an important role in the protection of iron and steel from corrosion in sea water, and the alloying of Zn and Ni can improve its corrosion resistance. The corrosion behavior of Zn？Ni alloys in synthetic sea water （3.5% NaCl, mass fraction） was studied using Tafel plot and electrochemical impedance spectroscopy （EIS） techniques. The corrosion resistance of the investigated alloys with various Ni contents （0.5%？10%, mass fraction） was compared with that of Zn. The results show that the corrosion resistance of Zn？Ni alloys （except 0.5% Ni） is superior to that of Zn. The 10% Ni gives the highest corrosion resistance due to the formation ofγ-Zn3Ni withγ-ZnNi phases in the alloy. In the case of alloy I （0.5% Ni）, it exhibits a higher corrosion rate （less corrosion resistance） than Zn.

Corrosion resistance of micro-arc oxidized ceramic coating on cast hypereutectic alloy

The corrosion resistance of the micro-arc oxidation(MAO) ceramic coating on a cast Al-13Si-5Cu alloy was investigated using various electrochemical methods including electrochemical impedance spectroscopy(EIS) and polarization curves.Microstructures of MAO ceramic coating were studied by SEM,and the influence of microscopic patterns on corrosion resistance was analyzed.The corrosion resistance of the aluminum alloy can be improved significantly by MAO process owing to increasing impedance and corrosion potential and decreasing corrosion current,and the ceramic coatings are composed of loose layer,compact layer and transition layer,which improve the corrosion resistance.The corrosin resistance is determined by the thickness of the compact layer and is not proportional to the total thickness of MAO,though the latter is one of the important factors influencing the corrosin resistance.

Effect of platform temperature on microstructure and corrosion resistance of selective laser melted Al-Mg-Sc alloy plate

The Al-3.40Mg-1.08Sc alloy plates were manufactured by selective laser melting(SLM) at platform temperatures of 35 ℃ and 200 ℃, respectively, and the corrosion performance of them was studied along height direction. The results show that the corrosion resistance of the alloy plate built at platform temperature of 35 ℃ along height direction is basically the same due to a uniform microstructure;While the corrosion resistance of the alloy plate built at platform temperature of 200 ℃ along height direction is different. The evolution of microstructure and the distribution of secondary phases are investigated, and the results show that the Cu-rich phases in alloy play a key role on corrosion performance. At higher platform temperature, the cooling rate is relative slow and a certain degree of in situ ageing leads to the significantly different distribution of Cu-rich phases along grain boundary. Specimens built at the platform temperature of 200 ℃ are inclined to locate at the crossed grain boundary, rather than continuous segregation of Cu-rich phases along grain boundary that is built at platform temperature of 35 ℃. Therefore, the corrosion resistance of Al-3.40Mg-1.08Sc alloy plate manufactured at platform temperature of 200 ℃ is higher, and presents a gradually decreasing trend along height direction.

Effects of cooling rate on bio-corrosion resistance and mechanical properties of Mg-1Zn-0.5Ca casting alloy

Mg?1Zn?0.5Ca alloys were prepared by traditional steel mould casting and water-cooled copper mould injection casting at higher cooling rate. Microstructure, mechanical properties and bio-corrosion resistance of two alloys were contrastively investigated. Grain size reduces remarkably and microstructure becomes homogenous when raising cooling rate. The bio-corrosion behaviour in 3.5% sodium chloride solution (3.5% NaCl) and Hank’s solution at 37°C was investigated using electrochemical polarization measurement and the results indicate that the alloy prepared at higher cooling rates has better corrosion resistance in both types of solution. Further mass loss immersion test in Hank’s solution reveals the same result. The reason of corrosion resistance improvement is that raising cooling rate brings about homogeneous microstructure, which leads to micro-galvanic corrosion alleviation. The tensile test results show that yield strength, ultimate tensile strength and elongation are improved by raising cooling rate and the improvement is mainly due to grain refinement.

Wear and corrosion properties of laser cladded Cu_(47)Ti_(34)Zr_(11)Ni_8/SiC amorphous composite coatings on AZ91D magnesium alloy

To improve the wear and corrosion properties of AZ91D magnesium alloys,Cu-based amorphous composite coatings were fabricated on AZ91D magnesium alloy by laser cladding using mixed powders of Cu47Ti34Zr11Ni8 and SiC.The wear and corrosion behaviours of the coatings were investigated.The wear resistance of the coatings was evaluated under dry sliding wear condition at room temperature.The corrosion resistance of the coatings was tested in 3.5%(mass fraction) NaCl solution.The coatings exhibit excellent wear resistance due to the recombined action of amorphous phase and different intermetallic compounds.The main wear mechanisms of the coatings and the AZ91D sample are different.The former is abrasive wear and the latter is adhesive wear.The coatings compared with AZ91D magnesium alloy also exhibit good corrosion resistance because of the presence of the amorphous phase in the coatings.

Improvement of surface corrosion resistance for magnesium alloy by combining thermal spray and cast-infiltration

The present work focuses on a new method combining cast-infiltration with thermal spraying technology to improve the surface corrosion resistance of magnesium alloy.A zinc-based alloy layer was fabricated on the surface of AZ91D magnesium alloy. The microstructure of the layer was characterized by scanning electron microscopy equipped with an energy dispersive X-ray spectroscopy(EDS).The phase constituent of these alloys was identified by X-ray diffractometry(XRD).The analysis results reveal that a zinc-based alloy layer with a thickness of 700μm can form on the surface of AZ91 alloy matrix.The layer is composed of Mg7Zn3,MgZn and a small amount of α-Mg solid solution.The results indicate that the corrosion-resistance of the specimen with a zinc-based alloy layer is much better than that of the specimen without the layer after being immersed in 5%NaCl solution for 240 h, and the layer is more protective for the AZ91 alloy.

Corrosion performance and tribological behavior of diamond-like carbon based coating applied on Ni−Al−bronze alloy

The effect of diamond-like carbon(DLC)coating(fabricated by cathodic arc deposition)on mechanical properties,tribological behavior and corrosion performance of the Ni−Al−bronze(NAB)alloy was investigated.Nano-hardness and pin-on-plate test showed that DLC coating had a greater hardness compared with NAB alloy.Besides,the decrease in friction coefficient from 0.2 for NAB substrate to 0.13 for the DLC-coated sample was observed.Potentiodynamic polarization and EIS results showed that the corrosion current density decreased from 2.5μA/cm2 for bare NAB alloy to 0.14μA/cm2 for DLC-coated sample in 3.5 wt.%NaCl solution.Moreover,the charge transfer resistance at the substrate−electrolyte interface increased from 3.3 kΩ·cm2 for NAB alloy to 120.8 kΩ·cm2 for DLC-coated alloy,which indicated an increase in corrosion resistance due to the DLC coating.

Effects of electrolytic concentration on properties of micro-arc film on Ti6Al4V alloy

To study the effect of electrolytic concentration,bioactive ceramic films containing Ca and P on the surface of the Ti6Al4V alloy were prepared by micro-arc oxidation(MAO) in aqueous solutions of different concentrations.Composition,micro-morphology,wettability of the films and their corrosion behavior in a Hank's SBF were studied.Our experimental results show that the film is mainly composed of anatase,rutile and amorphous phases.With an increase in electrolytic concentration,the ratio of rutile in films enlarge and small amounts of calcium phosphate(Ca3(PO4)2) and hydroxyapatite(HA) appear.The number of micropores in films increases but their dimensions decrease and their porosities increase slightly.As the surface roughness of MAO film increases with concentration,the wettablility of the oxide film improves continually,while micro-hardness increases at first and then decreases.MAO treatment clearly improves the corrosion resistance of substrates in a Hank's SBF.