在铜系复合催化剂存在下,采用乙醇与硅直接反应,得到以三乙氧基硅烷为主的反应液;将反应液进行减压蒸馏,收集25-45℃/2-5 k Pa下的馏分,产品纯度达到98%,总收率达80%。研究了硅粉活化时间及粒径、催化剂种类、溶剂种类对硅粉转化率和三...在铜系复合催化剂存在下,采用乙醇与硅直接反应,得到以三乙氧基硅烷为主的反应液;将反应液进行减压蒸馏,收集25-45℃/2-5 k Pa下的馏分,产品纯度达到98%,总收率达80%。研究了硅粉活化时间及粒径、催化剂种类、溶剂种类对硅粉转化率和三乙氧基硅烷选择性的影响。结果表明,最佳工艺条件为：溶剂选择聚乙氧基硅烷（聚合度3-5）,催化剂为无水氯化亚铜和双二乙基磷酸铜质量比1∶1的混合物,硅粉不经活化直接使用且粒径选择300-500目。展开更多
Pervaporation(PV),as an environmental friendly and energy-saving separation technology,has been received increasing attention in recent years.This article reviews the preparation and application of macroporous ceramic...Pervaporation(PV),as an environmental friendly and energy-saving separation technology,has been received increasing attention in recent years.This article reviews the preparation and application of macroporous ceramic-supported polymer composite pervaporation membranes.The separation materials of polymer/ceramic composite membranes presented here include hydrophobic polydimethylsiloxane(PDMS) and hydrophilic poly(vinyl alcohol)(PVA),chitosan(CS) and polyelectrolytes.The effects of ceramic support treatment,polymer solution properties,interfacial adhesion and incorporating or blending modification on the membrane structure and PV performance are discussed.Two in-situ characterization methods developed for polymer/ceramic composite membranes are also covered in the discussion.The applications of these composite membranes in pervaporation process are summarized as well,which contain the bio-fuels recovery,gasoline desulfuration and PV coupled proc-ess using PDMS/ceramic composite membrane,and dehydration of alcohols and esters using ceramic-supported PVA or PVA-CS composite membrane.Finally,a brief conclusion remark on polymer/ceramic composite mem-branes is given and possible future research is outlined.展开更多
Polydimethylsiloxane （PDMS）, tetraethoxysilane （TEOS）, ethyl alcohol （EtOH） and deionized water were main raw materials to prepare silicone-modified hybrid thin films using sol-gel method. The effect of the cont...Polydimethylsiloxane （PDMS）, tetraethoxysilane （TEOS）, ethyl alcohol （EtOH） and deionized water were main raw materials to prepare silicone-modified hybrid thin films using sol-gel method. The effect of the contents of H2O and PDMS on thin films was studied. When the volume ratio of H20 to TEOS is 0.5, the optimum quality of thin films is obtained. And the gelation time is affected slightly by H20 content. Uniform thin films are obtained when the volume ratio of PDMS to TEOS is 0.2. Yet, the sol would be inactive in 6 d. Various properties of thin films were studied, including hardness, adhesive quality, hydrophobic property, corrosion protection property, and abrasion resistance. Test results show that the pencil hardness is generally 3-6 H, and adhesive quality achieves the highest standard of 0. When the sintering temperature is below 400℃, the contact angle is about 95° and hydrophobic films are obtained. The abrasion resistance of thin films is better than that of aluminum alloy when the sintering temperature is higher than 300℃. And the excellent corrosion protective effect is obtained by single-layer coating when the sintering temperature is higher than 400℃.展开更多
Sorption isotherm of chloroform in polyvinyl dimethylsiloxane (PVDMS) polymer film was measured via the gravimetric method, and this film was confirmed experimentally to be good membrane material to recover chloroform...Sorption isotherm of chloroform in polyvinyl dimethylsiloxane (PVDMS) polymer film was measured via the gravimetric method, and this film was confirmed experimentally to be good membrane material to recover chloroform from gas stream with high sorption capacity. A new PVDMS-Al2O3 composite hollow fibre membrane was further prepared by coating a PVDMS film on the outer surface of Al2O3 hollow fibre porpous substrate prepared by a dry/wet phase inversion method. Microstructure of the composite membranes was examined by scanning electron microscopy (SEM), indicating the PVDMS coating layer was uniform, free of defects, and around 15μm thick. Performance of the PVDMS-Al2O3 composite hollow fibre membranes for chloroform recovery was investigated. By comparing the experimental data that derived from a mathematical model, the permeabilities of chloroform and nitrogen in the PVDMS polymer membrane were obtained. The effects of temperature and feed flow rate on the chloroform recovery and permeate concentration were investigated both experimentally and theoretically.展开更多
文摘在铜系复合催化剂存在下,采用乙醇与硅直接反应,得到以三乙氧基硅烷为主的反应液;将反应液进行减压蒸馏,收集25-45℃/2-5 k Pa下的馏分,产品纯度达到98%,总收率达80%。研究了硅粉活化时间及粒径、催化剂种类、溶剂种类对硅粉转化率和三乙氧基硅烷选择性的影响。结果表明,最佳工艺条件为：溶剂选择聚乙氧基硅烷（聚合度3-5）,催化剂为无水氯化亚铜和双二乙基磷酸铜质量比1∶1的混合物,硅粉不经活化直接使用且粒径选择300-500目。
文摘Pervaporation(PV),as an environmental friendly and energy-saving separation technology,has been received increasing attention in recent years.This article reviews the preparation and application of macroporous ceramic-supported polymer composite pervaporation membranes.The separation materials of polymer/ceramic composite membranes presented here include hydrophobic polydimethylsiloxane(PDMS) and hydrophilic poly(vinyl alcohol)(PVA),chitosan(CS) and polyelectrolytes.The effects of ceramic support treatment,polymer solution properties,interfacial adhesion and incorporating or blending modification on the membrane structure and PV performance are discussed.Two in-situ characterization methods developed for polymer/ceramic composite membranes are also covered in the discussion.The applications of these composite membranes in pervaporation process are summarized as well,which contain the bio-fuels recovery,gasoline desulfuration and PV coupled proc-ess using PDMS/ceramic composite membrane,and dehydration of alcohols and esters using ceramic-supported PVA or PVA-CS composite membrane.Finally,a brief conclusion remark on polymer/ceramic composite mem-branes is given and possible future research is outlined.
基金supported partly by the School of Mechanical,Electronic and Control Engineering,Beijing Jiaotong university,China
文摘Polydimethylsiloxane （PDMS）, tetraethoxysilane （TEOS）, ethyl alcohol （EtOH） and deionized water were main raw materials to prepare silicone-modified hybrid thin films using sol-gel method. The effect of the contents of H2O and PDMS on thin films was studied. When the volume ratio of H20 to TEOS is 0.5, the optimum quality of thin films is obtained. And the gelation time is affected slightly by H20 content. Uniform thin films are obtained when the volume ratio of PDMS to TEOS is 0.2. Yet, the sol would be inactive in 6 d. Various properties of thin films were studied, including hardness, adhesive quality, hydrophobic property, corrosion protection property, and abrasion resistance. Test results show that the pencil hardness is generally 3-6 H, and adhesive quality achieves the highest standard of 0. When the sintering temperature is below 400℃, the contact angle is about 95° and hydrophobic films are obtained. The abrasion resistance of thin films is better than that of aluminum alloy when the sintering temperature is higher than 300℃. And the excellent corrosion protective effect is obtained by single-layer coating when the sintering temperature is higher than 400℃.
文摘Sorption isotherm of chloroform in polyvinyl dimethylsiloxane (PVDMS) polymer film was measured via the gravimetric method, and this film was confirmed experimentally to be good membrane material to recover chloroform from gas stream with high sorption capacity. A new PVDMS-Al2O3 composite hollow fibre membrane was further prepared by coating a PVDMS film on the outer surface of Al2O3 hollow fibre porpous substrate prepared by a dry/wet phase inversion method. Microstructure of the composite membranes was examined by scanning electron microscopy (SEM), indicating the PVDMS coating layer was uniform, free of defects, and around 15μm thick. Performance of the PVDMS-Al2O3 composite hollow fibre membranes for chloroform recovery was investigated. By comparing the experimental data that derived from a mathematical model, the permeabilities of chloroform and nitrogen in the PVDMS polymer membrane were obtained. The effects of temperature and feed flow rate on the chloroform recovery and permeate concentration were investigated both experimentally and theoretically.
