Directional solidification of Mg-2.35Gd （mass fraction, %） magnesium alloy was carried out to investigate the effects of the solidification parameters （growth rate v and temperature gradient G） on microstructure a...Directional solidification of Mg-2.35Gd （mass fraction, %） magnesium alloy was carried out to investigate the effects of the solidification parameters （growth rate v and temperature gradient G） on microstructure and room temperature mechanical properties under the controlled solidification conditions. The specimens were solidified under steady state conditions with different temperature gradients （G=20, 25 and 30 K/mm） in a wide range of growth rates （v=10-200 μm/s） by using a Bridgman-type directional solidification furnace with liquid metal cooling （LMC） technology. The cellular microstructures are observed. The cellular spacing 2 decreases with increasing v for constant G or with increasing G for constant v. By using a linear regression analysis the relationships can be expressed as 2=136.216v^-0.2440 （G=30 K/mm） and 2=626.5630G^-0.5625 （v=10 μm/s）, which are in a good agreement with Trivedi model. An improved tensile strength and a corresponding decreased elongation are achieved in the directionally solidified experimental alloy with increasing growth rate and tempertaure gradient. Furthermore, the directionally solidified experimental alloy exhibits higher room temperature tensile strength than the non-directionally solidified alloy.展开更多
As-cast samples of the Al-3wt.%Ni-lwt.%Bi alloy resulting from the horizontal directional solidification process were subjected to the micro-abrasive wear test.The effects of the solidification thermal and microstruct...As-cast samples of the Al-3wt.%Ni-lwt.%Bi alloy resulting from the horizontal directional solidification process were subjected to the micro-abrasive wear test.The effects of the solidification thermal and microstructural parameters,such as the growth and cooling rates and the cellular and primary dendritic spacings(VL and TR;λ1 and λc;respectively),were evaluated in the wear resistance of the investigated alloy.The tribological parameters analyzed were the wear volume and rate(Vw and Rw).The solidification experiments and the wear tests were carried out by means of a water-cooled horizontal directional solidification device and a rotary-fixed ball wear machine,respectively.The results show lower Vw and Rw values correspond to finer microstructures and the Vw dependence on λ1 is characterized by an experimental mathematical equation.A better distribution of Bi soft droplets and Al3Ni hard intermetallic particles is observed within the finer interdendritic region and,in consequence,the better wear resistance is achieved in as-cast samples with dendritic morphology rather than cellular morphology.A transition of wear mechanism from adhesive to abrasive is observed.展开更多
基金Projects(51227001,51420105005)supported by the National Natural Science Foundation of ChinaProject(138-QP-2015)supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU),China
文摘Directional solidification of Mg-2.35Gd （mass fraction, %） magnesium alloy was carried out to investigate the effects of the solidification parameters （growth rate v and temperature gradient G） on microstructure and room temperature mechanical properties under the controlled solidification conditions. The specimens were solidified under steady state conditions with different temperature gradients （G=20, 25 and 30 K/mm） in a wide range of growth rates （v=10-200 μm/s） by using a Bridgman-type directional solidification furnace with liquid metal cooling （LMC） technology. The cellular microstructures are observed. The cellular spacing 2 decreases with increasing v for constant G or with increasing G for constant v. By using a linear regression analysis the relationships can be expressed as 2=136.216v^-0.2440 （G=30 K/mm） and 2=626.5630G^-0.5625 （v=10 μm/s）, which are in a good agreement with Trivedi model. An improved tensile strength and a corresponding decreased elongation are achieved in the directionally solidified experimental alloy with increasing growth rate and tempertaure gradient. Furthermore, the directionally solidified experimental alloy exhibits higher room temperature tensile strength than the non-directionally solidified alloy.
基金financial support provided by IFPA-Federal Institute of Education, Science and Technology of Pará, UFPA-Federal University of Pará, and CNPq-The Brazilian Research Council (grants 302846/2017-4 and 400634/2016-3)CAPES-Coordenacao de Aperfeicoamento de Pessoal de Nível SuperiorBrasil-Finance Code 001
文摘As-cast samples of the Al-3wt.%Ni-lwt.%Bi alloy resulting from the horizontal directional solidification process were subjected to the micro-abrasive wear test.The effects of the solidification thermal and microstructural parameters,such as the growth and cooling rates and the cellular and primary dendritic spacings(VL and TR;λ1 and λc;respectively),were evaluated in the wear resistance of the investigated alloy.The tribological parameters analyzed were the wear volume and rate(Vw and Rw).The solidification experiments and the wear tests were carried out by means of a water-cooled horizontal directional solidification device and a rotary-fixed ball wear machine,respectively.The results show lower Vw and Rw values correspond to finer microstructures and the Vw dependence on λ1 is characterized by an experimental mathematical equation.A better distribution of Bi soft droplets and Al3Ni hard intermetallic particles is observed within the finer interdendritic region and,in consequence,the better wear resistance is achieved in as-cast samples with dendritic morphology rather than cellular morphology.A transition of wear mechanism from adhesive to abrasive is observed.
