This research adopted four methods to toughen epoxy adhesives. They were liquid hydroxyl group terminated polybutadiene (HTPB) rubber modification, silicon rubber modification, polyacrylate multiplicity elastomer par...This research adopted four methods to toughen epoxy adhesives. They were liquid hydroxyl group terminated polybutadiene (HTPB) rubber modification, silicon rubber modification, polyacrylate multiplicity elastomer particulates emulsion modification and chemical grafting modification. After modification, the shearing strength and the rupture elongation were tested. The interface and the chemical reaction between the modifiers and the epoxy were analyzed by scanning electron microscope (SEM) and infrared optical spectrum. The results show that the elastomer particulates modification and the chemical grafting modification can reach the better toughening effects.展开更多
Objective To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.Methods Twelve caries-free human primary molars were randomly di...Objective To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.Methods Twelve caries-free human primary molars were randomly divided into 2 groups with 6 teeth each.In group 1,each tooth was hemisected into two halves.One half was assigned to control subgroup 1,which was bonded with a single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 1 in which the adhesive was applied three times before light curing.In group 2,the teeth were also hemisected into two halves.One half was assigned to control subgroup 2,which was bonded with the single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 2 in which three layers of adhesive were applied with light curing each successive layer.Microtensile bond strength was immediately tested after specimen preparation.Results When the adhesive was applied three times before light curing,the bond strength of the experimental subgroup 1(n=33,57.49±11.61 MPa) was higher than that of the control subgroup 1(n=31,49.71±11.43 MPa,P<0.05).When using the technique of applying multiple layers of adhesive with light curing each successive layer,no difference of immediate bond strength was observed between the control subgroup 2 and the experimental subgroup 2(P>0.05).Conclusion Multiple coatings of one-step self-etching adhesive can increase the immediate bond strength to primary dentin when using the technique of light-curing after applying three layers of adhesive.展开更多
文摘This research adopted four methods to toughen epoxy adhesives. They were liquid hydroxyl group terminated polybutadiene (HTPB) rubber modification, silicon rubber modification, polyacrylate multiplicity elastomer particulates emulsion modification and chemical grafting modification. After modification, the shearing strength and the rupture elongation were tested. The interface and the chemical reaction between the modifiers and the epoxy were analyzed by scanning electron microscope (SEM) and infrared optical spectrum. The results show that the elastomer particulates modification and the chemical grafting modification can reach the better toughening effects.
文摘Objective To investigate the effect of multiple coatings of the one-step self-etching adhesive on immediate microtensile bond strength to primary dentin.Methods Twelve caries-free human primary molars were randomly divided into 2 groups with 6 teeth each.In group 1,each tooth was hemisected into two halves.One half was assigned to control subgroup 1,which was bonded with a single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 1 in which the adhesive was applied three times before light curing.In group 2,the teeth were also hemisected into two halves.One half was assigned to control subgroup 2,which was bonded with the single-step self-etching adhesive according to the manufacturer's instructions;the other half was assigned to experimental subgroup 2 in which three layers of adhesive were applied with light curing each successive layer.Microtensile bond strength was immediately tested after specimen preparation.Results When the adhesive was applied three times before light curing,the bond strength of the experimental subgroup 1(n=33,57.49±11.61 MPa) was higher than that of the control subgroup 1(n=31,49.71±11.43 MPa,P<0.05).When using the technique of applying multiple layers of adhesive with light curing each successive layer,no difference of immediate bond strength was observed between the control subgroup 2 and the experimental subgroup 2(P>0.05).Conclusion Multiple coatings of one-step self-etching adhesive can increase the immediate bond strength to primary dentin when using the technique of light-curing after applying three layers of adhesive.
