JET上在有高快离子能含量下只有ICRF放电的一种新型MHD活性

在有离子回旋共振频率（ICRF）加热和改变等离子体密度的情况下，在JET托卡马克中进行的放电中，已研究了在甚高快离子能含量时锯齿稳定问题，等离子体密度的改变是通过吹氘气加以控制的，在这些实验中，已观测到锯齿性能的惊人差别，当等离子体密度nc减小到低于某个阈值时，居齿频率和崩塌持续时间增加5倍，因为由于快离子慢化时间与nc成反比而快离子能含量随nc减小而增加，所以nc阈值相应于快离子能含量阈值，在这些实验中，当快离子能量对总等离子体抗磁能含量的贡献变得大于45％时达到此阈值，在频率介于55和65kHz之间，环向模数n=1时，有短的无锯齿周期的锯齿活性伴随有MHD活性，这种活性解释为与ICRF驱动的快离子共振的高能粒子鱼骨模，看来实验结果是与锯齿和鱼骨模的稳定性图一致的[White 1989:Theory of Tokamak Plasmas(Amsterdam:North-Holland)]，探索在此图中有甚大快离子群体的那部分。

米草光合作用速率季节变化及其对初级生产的影响

对江苏省滨海具盐沼生态系统中大米草和互花米草群落有关生理生态学指标进行了为期一年的定位观察和测定。结果表明：互花米草和大米草，地上生物量（干重）在９月达到最高值，分别为１７１４ｇ／ｍ￣２和４１９ｇ／ｍ￣２；叶绿素季节变化模式分别呈斜“Ｚ”型和扁“Ｗ”型。两种米草光合作用同化率６月明显高于９月．植物材料能含量变化从１２．５６ｋＪ／ｇ到２０．１０ｋＪ／ｇ。

Decarburization and improvement of ultra fine straight WC-8Co sintered via microwave sintering

Cemented tungsten carbide with ultra fine grains was prepared via microwave sintering.η phase（W3Co3C） was formed on the surface of the samples during the preparation process.Extra carbon black was premixed and the influence of carbon content on mechanical properties was studied.The results show that the maximum value of hardness and transverse rupture strength are HRA 93.2 and 3396 MPa respectively when the carbon black content is 0.45%.The microstructure investigated by SEM show that the WC grains growth mainly occurs during the early stage of microwave sintering by the coalescence of grains.

Influence of hydrogen content on room temperature compressive properties of Ti-6Al-4V alloy at high strain rate

Electromagnetic forming tests were done at room temperature to reveal the influence of hydrogen content on the compressive properties of Ti-6Al-4V alloy at high strain rate. Microstructure was observed to reveal the mechanism of hydrogen-enhanced compressive properties. The experimental results indicate that hydrogen has favorable effects on the compressive properties of Ti-6Al-4V alloy at high strain rate. Compression of Ti-6Al-4V alloy first increases up to a maximum and then decreases with the increase of hydrogen content at the same discharge energy under EMF tests. The compression increases by 47.0% when 0.2% (mass fraction) hydrogen is introduced into Ti-6Al-4V alloy. The optimal hydrogen content for cold formation of Ti–6Al–4V alloy under EMF was determined. The reasons for the hydrogen-induced compressive properties were discussed.

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

手持PC并不远

■ IT业界巨头比尔·盖茨先生近日在芬兰预言,5年后的个人电脑将是可以装在口袋里的便携式无绳微机,能看、能听、能学习,成为人人会使用的工具。今天的手持PC就是盖茨先生预言的明日电脑的雏形。

打造灰领人才 遭遇四大瓶颈

劳动和社会保障部近日公布,中国计划在未来三年培养50万被称为"高级蓝领"的高技能人才,主要集中在制造业、服务业及其他技能含量较高的职业。在前不久结束的全国人才工作会议上,高技能人才培养也被提到了国家人才开发战略的高度。但在采访中记者发现,打造高技能人才还存在四大瓶颈。

Effect of Si,Cu and Fe on mechanical properties of cast semi-solid 206 alloys

The development of a modified 206 alloy whose composition was optimized to minimize hot tearing during semi-solid forming was reported. The effect of varying silicon, copper and iron contents was investigated using a design of experiment (DOE) approach. Semi-solid slurries were prepared using the SEED process and injected into a high pressure die casting press. The hot tearing sensitivity results were reported for different alloy variants. The microstructure evolution during the semi-solid preparation was presented along with actual die cast components. The effects of silicon, copper and iron on mechanical properties in the T7 condition were also analyzed. Beyond the benefit of reducing hot tearing, it is shown that the tensile and fatigue properties remain compatible with the automotive industry requirements.

Microstructure, hydrogen storage thermodynamics and kinetics of La_5Mg_(95-x)Ni_x(x=5, 10, 15) alloys

The microstructure, hydrogen storage thermodynamics and kinetics of La5Mg95-xNix (x=5, 10, 15) ternary alloys with different Ni contents were investigated. The evolutions of the microstructure and phase of experimental alloys were characterized by X-ray diffractometry and scanning electron microscopy. The hydrogen storage kinetics and thermodynamics, and P-C-I curves were tested using a Sievert apparatus. It is found that increasing Ni content remarkably improves hydrogen storage kinetics but reduces the hydrogen storage capacity of alloys. The highest hydrogen absorption/desorption rate is observed in the La5Mg80Ni15 alloy, with the lowest hydrogen desorption activation value being 57.7 kJ/mol. By means of P-C-I curves and the van’t Hoff equation, it is determined that the thermodynamic performance of the alloy is initially improved and then degraded with increasing Ni content. The La5Mg85Ni10 alloy has the best thermodynamics properties with a hydrogenation enthalpy of -72.1 kJ/mol and hydrogenation entropy of -123.2 J/(mol·K).

Effect of Si content on laser welding performance of Al-Mn-Mg alloy

The correlation between Si content （0.1%-0.5%, mass fraction） and pulse laser welding performance of AI-Mn-Mg aluminum alloy sheets was studied. The sheets were fabricated in the laboratory, with gauge of 0.45 mm, H16 temper by pulse laser welding. It was found that no cracking existed in the welding pool as Si content was below 0.34%. However, when the Si content increased to 0.47%, cracking formed in the welding pool. Microstructure observations indicated that residual eutectic phases distributed at the grain boundaries were discontinuous and appeared to be small particles in lower Si content alloys; the residual eutectic phases distributed at the grain boundaries were partially continuous and appeared to be films in higher Si content alloys. These phenomena could explain why Si content adversely affected the laser welding performance.

Effects of minor Zn content on microstructure and corrosion properties of Al-Mg alloy

The effects of different Zn contents in Al-Mg alloy on the microstructure characterizations were observed by advanced electron microscopy and the corrosion properties were investigated by the inter-granular corrosion tests,the exfoliation corrosion tests,and the Potentiodynamic polarizaion tests.The τ phase(Mg_(32)(Al,Zn)_(49)) forms on the pre-existing Mn-rich particles and at the grain boundaries.According to the theory of binding energy,the formation of τ phase is much easier than that of β phase(Al_3Mg_2),somehow replacing β phase and reducing the possibility of β phase precipitation.This change dramatically decreases the susceptibility of corrosion.The Zn addition increases the corrosion resistance of Al-Mg alloy with an optimal value of 0.31%.When the Zn addition is increased to 0.78%,however,the corrosion resistance of alloy decreases once again but it is still better than that of the alloy without Zn addition.

Fixed Ammonium Contents and NH Fixation Capaci-ties of Some Cnltivated Soils in China

Fixed ammonium contents and fixation capacities of some representative cultivated soils collectedfrom 16 provinces of China were studied. Results showed that the contents of fixed ammonium in soilsranged from 35 to 573 mg N kg￣(-1), with an average of 198 mg N kg￣(-1). The content of fixed ammoniumcorrelated very significantly with mica content for tropical and subtropical soils, whereas this was not thecase for soils in the temperate zone. At the end of K-exhansting experiment the fixed ammonium contentincreased in most soils studied. However, it decreased in some temperate soils. Generally, fixation of addedNH could not be found either before or after K-exhausting experiment for highly weathered soils, includingtropical soils and soils derived from granite-gneiss or Quaternary red clays in the subtropic zonet while formost soils in the Yangtze River dalta the NH fixation capacity was rather high and increased siguificantlyin the K-exhausted soils.

Microbial Development in Soils Under Intensively Managed Bamboo (Phyllostachys praecox) Stands

Phyllostachys praecox C. D. Chu et C. S. Chao, a favored bamboo shoot species, has been widely planted in recent years. Four stands with different historical management practices were selected for this study to understand the evolution of soil microbial ecology by determining the effects of a new mulching and heavy fertilization practice on soil quality using microbiological parameters. Compared with the traditional practice (index 1), microbial biomass carbon (MBC) and soil microbial respiration carbon (MRC) with the new management practice significantly decreased (P ＜ 0.01 and P ＜ 0.05,respectively) with 1-2 years of mulching (index 2) and then for continued mulching significantly increased (P ＜ 0.05). The ratios of MBC/TOC (total organic carbon) and MRC/TOC also significantly diminished (P ＜ 0.05) with mulching. The average well color development (AWCD) and Shannon index decreased with mulching time, and the significant decrease(P ＜ 0.05) in Shannon index occurred from index 2 to index 3. The results from a principal components analysis (PCA)showed that the scores of the first principal component for indexes 1 and 2 were significantly larger (P ＜ 0.05) than soils mulched 3-4 years or 5-6 years. Also, the second principal component scores for index 1 were larger than those for index 2, suggesting that the ability of soil microorganisms to utilize soil carbon was decreasing with longer use of the new management practice and causing a deterioration of soil biological properties.

Effect of Zn content on tensile and electrochemical properties of 3003 Al alloy

The effect of Zn addition on the microstructure, tensile properties and electrochemical properties of as-annealed 3003 Al alloy was investigated through TEM observations, tensile tests and Tafel polarization analysis. High density precipitates are observed in the Zn-containing alloys and the alloy with 1.8% Zn addition also has rod-like precipitates. Tensile test results indicate that Zn has a great effect on tensile strength of 3003 Al alloy. The alloy with 1.5% Zn addition has the highest ultimate tensile strength. The electrochemical results indicate that Zn addition to 3003 Al alloy also has great impact on the corrosion potential of the 3003 A1 alloy in 0.5% NaCl solution and ethylene glycol-water solution. The corrosion potential varies with the Zn content and shifts negatively.

Effects of different periods of renal ischemia on liver as a remote organ

AIM:To assess the hepatic changes after induction of different periods of renal ischemia. METHODS:Rats were subjected to either sham operation or ischemia (30,45 and 60 min) followed by 60 min reperfusion. Liver and renal functional indices were measured. Hepatic glutathione (GSH) and ferric reducing antioxidant power levels and the concentration of interleukin (IL)-10 and tumor necrosis factor (TNF-α) were evaluated. Portions of liver and kidney tissues were fixed for histological evaluation. RESULTS:Forty-five minutes renal ischemia followed by 60 min reperfusion caused significant changes in liver structure and a significant reduction in renalfunction. These rats showed a significant decrease in liver GSH,as well as a significant increase in TNF-α and IL-10 concentrations. These results demonstrated that renal ischemia caused changes in liver histology,function,oxidative stress and inflammatory status,which led to a reduction in hepatic antioxidant capacity. With 30 min ischemia,the magnitude of these changes was less than those with 45 or 60 min ischemia.CONCLUSION:A minimum of 45 min ischemia is needed to study the effects of renal injury on the liver as a remote organ.

Basic theory research of coal spontaneous combustion

Discussed latest research results of basic theory research of coal spontaneous combustion in detail,with quantum chemical theory and method and experiment syste- matically studied chemical structure of coal molecule,adsorption mechanism of coal sur- face to oxygen molecule and chemical reaction mechanism and process of spontaneous combustion of organic macromolecule and low molecular weight compound in coal from microcosmic view,and established complete theoretical system of the mechanism of coal spontaneous combustion.

Effect of graphite content on wear property of graphite/Al_2O_3/Mg-9Al-1Zn-0.8Ce composites

Using squeeze-infiltration technique, Mg-9Al-1Zn-0.8Ce composite reinforced by graphite particles and Al2O3 short fibers was fabricated. The reinforcing phases combined closely with the matrix and no agglomeration was observed. The microstructure, hardness and wear property of the composites with the graphite content of 5%, 10%, 15% and 20% were investigated, respectively. The results reveal that Ce tends to enrich around the boundaries of graphite particles and Al2O3 short fibers, and forms Al3Ce phase. When the graphite content increases to 20%, the grain size becomes small. Moreover, with increasing the graphite content, the microhardness of the composites decreases but the wear resistance increases. The graphite which works as lubricant during dry sliding process decreases the wear loss. At low load, the wear mechanism of the composite is mainly abrasive wear and oxidation wear; at high load, except that the composite with 20% graphite is still with abrasive wear and oxidation wear, the wear mechanism of other composites changes to delamination wear.

Inconsistence of Non-Singular Spherically Symmetric Solution and a Satisfactory Energy-Momentum Complex

Two spherically symmetric non-singular black hole solutions in Moiler tetrad theory of gravitation have been obtained. Although the two solutions have the same form of metric （spherically symmetric nonsingular black hole）, their energy contents are different. We use another method given by Gibbons and Hawking to calculate the energy content of these solutions. We also obtained different value of energy. Study the requirements of a satisfactory energymomentum complex given by Moiler we find that the second solution, which behaves as 1/√r, is not transformed as a four-vector under Lorentz transformation.

Quantum Dynamics Study on D＋OD＋ Reaction： Competition between Exchange and Abstraction Channels

Quantum dynamics for the D＋OD＋ reaction at the collision energy range of 0.0-1.0 eV was studied on an accurate ab initio potential energy surface. Both of the endothermic abstraction （D＋OD＋-→O＋＋D2） and thermoneutral exchange （D＋OD＋--＊D＋OD＋） channels were investigated from the same set of time-dependent quantum wave packets method under cen- trifugal sudden approximation. The reaction probability dependence with collision energy, the integral cross sections, and the thermal rate constant of the both channels are calculated. It is found that there is a convex structure in the reaction path of the exchange reaction. The calculated time evolution of the wave packet distribution at J=0 clearly indicates that the convex structure significantly influences the dynamics of the exchange and abstraction channels of title reaction.