Effect of benzoxazine resin on mechanical properties of nitrile rubber composites: Experiment and molecular simulation

Benzoxazine resin,being a new type of phenolic resin deve-loped to overcome the shortcomings of traditional phenolic resins,has been synthesized from phenol,formaldehyde and amine,and does not require solvent elimination or monomer purification to obtain a relatively clean precursor.It has potential application in the field of aerospace due to its low expansion coefficient,high weather resistance,high carbon yield,good mechanical strength,and excellent ablation resistance[1].It can be mixed with various other resins or polymers to produce new resins with a broad range of applications[2-3].

复杂工程系统自组织问题研究综述

随着科学技术的发展,产生了许多复杂的工程活动和复杂工程系统。这类工程的要素十分庞杂,要素之间的非线性相互作用很强,传统的工程方法已经难以应付。面对这种情况,人们开始将复杂性科学中的某些思想尤其是自组织理论应用到工程问题中来,出现了一些应对复杂工程问题的新思路和新方法。本文通过国内外文献综述,阐明了复杂工程系统的概念及特点,从三个层面评述了关于复杂工程系统自组织问题的研究进展:复杂工程系统的自性能、复杂工程系统的自组织机制以及复杂工程系统中自组织与他组织的关系。作者认为,目前基于模拟仿真而得到的研究成果在工程实践中是否有效,尚待检验;关于复杂工程系统的建构,还需要探讨一般性的原则和规律;对于复杂工程系统自性能的研究,与工程实践也有不小差距;在复杂工程系统建构过程中,如何权衡自组织与他组织之间的关系,需要重点展开研究。对于这些问题的探讨,不仅需要一般意义上的工程科学研究,也需要工程哲学研究的介入,尤其是在工程方法论层面,工程哲学可以做出自己独特的贡献。

Observation and characterization of asphalt microstructure by atomic force microscopy

The microstructure of asphalt is investigated by atomic force microscopy （AFM）. In order to analyze the impacts of asphalt types on microstructures, two neat asphalts with different penetration grades （50# and 70#） and one styrene-butadiene-styrene （SBS） modified asphalt are chosen. The influence of short-term aging is also studied. Based on the knowledge of asphalt＇s microproperties, the relationship between microstructures and healing property is analyzed. The results indicate that the microstructures of three asphalts are quite different and the effects of aging on the surface characteristics for different asphalts are also different. It is proposed that the bee structure is a type of wax crystal and it has a close relationship with the ＂bridge-healing＂ mechanism. The findings may reveal the formation mechanism of microstructure and the healing property for asphalts.

Effect of wear conditions on tribological properties of electrolessly-deposited Ni-P-Gr-SiC hybrid composite coating

The friction and wear properties of the electrolessly-deposited Ni-P-Gr-SiC composites were investigated. The effects of graphite content, load and rotation speed on the friction coefficient and wear resistance of the composite coatings were mainly investigated. The worn surface and cross section of the coatings were characterized by scanning electron microscopy and energy-dispersive X-ray analysis. The results show that the composite coatings reveal good antifriction and wear resistance due to the synergic effect of graphite and SiC particles. The formation of graphite-rich mechanically mixed layer （GRMML） on the surface of Ni-P-Gr-SiC coating contributes to the good tribological behavior of the wear counterparts and SiC particles play a load bearing role in protecting GRMML from shearing easily.

Performance of Wavelet-Transform-Domain Adaptive Equalizers

In this paper performances of wavelet transform domain (WTD) adaptive equalizers based on the least mean￣square (LMS) algorithm are analyzed. The optimum Wiener solution, the condition of convergence, the minimum mean square error (MSE) and the steady state excess MSE of the WTD adaptive equalizer are obtained. Constant and time varying convergence factor adaptive algorithms are studied respectively. Computational complexities of WTD LMS equalizers are given. The equalizer in WTD shows much better convergence performance than that of the conventional in time domain.

Wear behavior of SiC/PyC composite materials prepared by electromagnetic-field-assisted CVI

Silicon carbide/pyrolytic carbon (SiC/PyC) composite materials with excellent performance of self-lubrication and wear resistance were prepared on SiC substrates by electromagnetic-field-assisted chemical vapor infiltration (CVI). The composition and microstructure of the SiC/PyC materials were investigated in detail by XRD, SEM and EDS, etc. The effects of the deposition temperature on the section features and wear resistance of the SiC/PyC were studied. The results show that the PyC layers were deposited onto SiC substrates spontaneously at a lower deposition temperature. The SiC substrates deposited with PyC can significantly reduce the wear rate of the self-dual composite materials under dry sliding condition. The wear tests suggest that the SiC/PyC composite materials own a better wear resistance property when the deposition temperature is 800 °C, and the wear rate is about 64.6% of that without the deposition of PyC.

Theoretical Study of Antiferrodistortive Phase Transition in Strontium Titanate

At 105 K, strontium titanate is known to undergo an antiferrodistortive transition transform-ing from cubic to tetragonal structure as a result of the rotation of the oxygen octahedral around a cubic axe. Based on the Curie principle, the order parameter is determined to be a third-order complete symmetry polarization tensor. To take into account of quantum effects,the dielectric permittivity is measured from Landau free energy, and the Curie Weiss-type behavior is analyzed. From crystallization chemistry viewpoint, the dielectric behavior at low temperature is connected to small radius of Sr^2＋, which is much easier to move around the oxygen octahedral than Ba^2＋ in BaTiO3 or Pb^2＋ in PbTiO3.

Influence of pyrolysis temperature on structure and dielectric properties of polycarbosilane derived silicon carbide ceramic

β-SiC ceramic powders were obtained by pyrolyzing polycarbosilane in vacuum at 800-1200 °C. The β-SiC ceramic powders were characterized by TGA/DSC, XRD and Raman spectroscopy. The dielectric properties of β-SiC ceramic powders were investigated by measuring their complex permittivity by rectangle wave guide method in the frequency range of 8.2-18 GHz. The results show that both real part ε′ and imaginary part ε″ of complex permittivity increase with increasing pyrolysis temperature. The mechanism was proposed that order carbon formed at high temperature resulted in electron relaxation polarization and conductance loss, which contributes to the increase in complex permittivity.

Preparation and tribological performances of Ni-P-multi-walled carbon nanotubes composite coatings

Multi-walled carbon nanotubes （MWNTs） were wet-milled in the presence of ammonia and cationic surfactant and then used as reinforcements to prepare Ni-P-MWNTs composite coatings by electroless plating. The tribological performances of the composite coatings under dry condition were investigated in comparison with 45 steel and conventional Ni-P coating, Micrographs show that short MWNTs with uniform length and open tips were obtained through the wet-milling process. The results of wear test reveal that the Ni-P-MWNTs composite coatings posses much better friction reduction and anti-wear performances when compared with 45 steel and Ni-P coating. Within the MWNTs content range of 0.74%-1.97%, the friction coefficient and the volume wear rate of the composite coatings decrease gradually and reach the minimum values of 0.08 and 6.22x10-15 m3/（N.m）, respectively. The excellent tribological performances of the composite coatings can be attributed to the introduction of MWNTs, which play both roles of reinforcements and solid lubricant during the wear process.

Preparation, formation mechanism and mechanical properties of multilayered TiO_2-organic nanocomposite film

Ti O2-organic multilayered nanocomposite films were deposited on a self-assembled monolayer-coated silicon substrate based on layer-by-layer technique and chemical bath deposition method by a hydrolysis of Ti Cl4 in an acid aqueous solution. The chemical compositions, surface morphologies and mechanical properties of the films were investigated by X-ray photoelectron spectrometer(XPS), scanning electron microscopy(SEM) and nanoindentation depth-sensing technique, respectively. The results indicate that the major chemical compositions of the films are Ti and O. The principal mechanism for the nucleation and growth of the films is homogeneous nucleation, and the layer number of films has great influence on the surface morphology and roughness of the films. In addition, mechanical nanoindentation testing presents a significant increase in hardness and fracture toughness of titanium dioxide multilayered films compared with single-layer titanium dioxide thin film.

Effect of P addition on mineral transition of CaO-Al_2O_3-SiO_2 system during high-temperature sintering

The mineral transition, microstructure and self-pulverization as well as the Al2O3 leaching performance of calcium aluminate clinkers with different P additions in CaO-Al2O3-SiO2 system during high-temperature sintering were systematically studied by XRF, XRD, SEM-EDS and DSC-TG technologies. The clinkers sintered at 1350 °C mainly contain 12CaO·7Al2O3, CaO·Al2O3,β-2CaO·SiO2 and γ-2CaO·SiO2. The content of β-2CaO·SiO2 increases while the content of γ-2CaO·SiO2 decreases as the P addition increases. The self-pulverization property of clinkers deteriorates with increasing P addition. P distributes evenly in the clinkers, and inhibits the transformation of β-2CaO·SiO2 to γ-2CaO·SiO2. The cell volumes of 12CaO·7Al2O3 and CaO·Al2O3 decrease and increase respectively as the P addition increases, and P decreases their formation temperatures. The Al2O3 leaching rate of calcium aluminate clinkers decreases obviously with increasing P addition, which decreases form 95.01% to 83.84% as the P addition increases from 0 to 0.85%.

Influence of compression on thermal and corrosion behavior of Fe_(78)Si_9B_(13) glassy alloy

The Fe78Si9B13 glassy ribbons were compressed at room temperature with different pressures. The thermal and corrosion behaviors were investigated using various experimental techniques. The X-ray diffraction （XRD） and dilatometer （DIL） results show that the Fe78Si9B13 ribbons are in full amorphous state after pressing and the amount of free volume increases monotonically with increasing pressure. The corrosion resistance of the glassy alloys in various solutions decreases after compression at 10 MPa, but increases after compression at 20 MPa. The non-monotonic change of corrosion resistance is consistent with the result of electrical resistivity, which can be explained by the combining action of free volume that is introduced by the compression and the segregation of Si atoms in the samples.

Feasibility and safety of autologous bone marrow mononuclear cell transplantation in patients with advanced chronic liver disease

AIM： To evaluate the safety and feasibility of bone marrow cell （BMC） transplantation in patients with chronic liver disease on the waiting list for liver transplantation. METHODS： Ten patients （eight males） with chronic liver disease were enrolled to receive infusion of autologous bone marrow-derived cells. Seven patients were classified as Child-Pugh B and three as Child-Pugh C. Baseline assessment included complete clinical and laboratory evaluation and abdominal MRI. Approximately 50 mL of bone marrow aspirate was prepared by centrifugation in a ficoll-hypaque gradient. At least of 100 millions of mononuclear-enriched BMCs were infused into the hepatic artery using the routine technique for arterial chemoembolization for liver tumors. Patients were followed up for adverse events up to 4 mo. RESULTS： The median age of the patients was 52 years （range 24-70 years）. All patients were discharged 48 h after BMC infusion. Two patients complained ofmild pain at the bone marrow needle puncture site. No other complications or specific side effects related to the procedure were observed. Bilirubin levels were lower at 1 （2.19 ± 0.9） and 4 mo （2.10 ± 1.0） after cell transplantation that baseline levels （238 ± 1.2）. Albumin levels 4 mo after BMC infusion （3.73 ± 0.5） were higher than baseline levels （3.47 ± 0.5）. International normalized ratio （INR） decreased from 1.48 （SD = 0.23） to 1.43 （SD = 0.23） one month after cell transplantation. CONCLUSION： BMC infusion into hepatic artery of patients with advanced chronic liver disease is safe and feasible. In addition, a decrease in mean serum bilirubin and INR levels and an increase in albumin levels are observed. Our data warrant further studies in order to evaluate the effect of BMC transplantation in patients with advanced chronic liver disease.

Study on Tribological Properties of the Rolling Fluid Containing Nano-MoS_2 for Cold Rolling of Steel Strip

The nano-MoS2 particles were adopted to substitute for the extreme-pressure and anti-wear additives to the rolling fluid for steel strips.An optimal formulation and technical process for adding nano-MoS2 particles to the rolling fluid were obtained through orthogonal experiments with three factors at three levels.The tests have led to the following conclusions:(a) the nanoparticles should be added to a base oil with high saponification value;(b) the concentration of nanoparticles in rolling fluid should be equal to 0.6%;and (c) when the reaction time needed for surfactants (oleic acid,for example) to modify the nanoparticles was 40 min,the rolling fluid could have the best tribological properties.The lubricity of rolling fluid was verified by using a 4-high cold rolling test mill which showed that the rolling fluid with nano-MoS2 particles had the excellent lubricant performance to improve the surface quality of the steel strip remarkably.The mechanism of nano-MoS2 particles in the rolling process has been investigated by a series of characterization instruments,which have showed that,with its fullerene-like structure,the nano-MoS2 particles have self-lubricating properties and extra-low friction coefficient,and can easily form a protective film with low shear strength on the surface of friction pairs.

Variable step-size affine projection algorithm based on global speech absence probability for adaptive feedback cancellation

A novel approach is proposed for improving adaptive feedback cancellation using a variable step-size affine projection algorithm(VSS-APA) based on global speech absence probability(GSAP).The variable step-size of the proposed VSS-APA is adjusted according to the GSAP of the current frame.The weight vector of the adaptive filter is updated by the probability of the speech absence.The performance measure of acoustic feedback cancellation is evaluated using normalized misalignment.Experimental results demonstrate that the proposed approach has better performance than the normalized least mean square(NLMS) and the constant step-size affine projection algorithms.

Interference analysis and improvement of capacity reduction for FHSS networks in WPAN application environment

The coexistence between Bluetooth system and IEEE 802.11 frequency hoppingspread spectrum (FHSS) equipment is analyzed. Based on the capacity formulae and system simulation,the inter-affection between these networks is compared. A fragment adaptive solution of packetpayload length is presented, which can be used to improve the capacity reduction of IEEE 802.11 FHSSnetwork. Analysis results show that the IEEE 802.11 WLAN standard with its inherent mechanismsupports this fragment length adaptive algorithm. With the increasing of Bluetooth interferingnetworks, this adaptive solution can effectively relieve capacity decreasing of IEEE 802.11 FHSSnetwork. The capacity analysis method and adaptive algorithm adopted in this paper can also begeneralized into other FHSS networks.

Parameter optimization model in electrical discharge machining process

Electrical discharge machining (EDM) process, at present is still an experience process, wherein selected parameters are often far from the optimum, and at the same time selecting optimization parameters is costly and time consuming. In this paper, artificial neural network (ANN) and genetic algorithm (GA) are used together to establish the parameter optimization model. An ANN model which adapts Levenberg-Marquardt algorithm has been set up to represent the relationship between material removal rate (MRR) and input parameters, and GA is used to optimize parameters, so that optimization results are obtained. The model is shown to be effective, and MRR is improved using optimized machining parameters.

Comparison of locomotor behaviour between white-headed langurs Trachypithecus leucocephalus and Franois' langurs T. franoisi in Fusui,China

We studied the locomotor behaviour of white-headed langurs Trachypithecus leucocephalus and Francois＇ langurs T.francoisi to test two hypotheses： （1） these monkeys have evolved locomotor ability to support their activities on limestone hills, and （2） Francois＇ langurs have evolved more diverse locomotor skills than white-headed langurs. Data were collected from 1996 - 1998 and in 2005 in Fusui Nature Reserve, Guangxi, and showed that the two species had similar locomotor types, but Francois＇ langurs had more locomotor modes （26） than white-headed langurs （12）. Quadrupedal walking and leaping were two major types, and white-headed langurs were more arboreal than Francois＇ langurs. We suggest that, while keeping their ancestral locomotor types, the two species have evolved new types allowing them to live on limestone cliffs. Compared to white-headed langurs, Francois＇ langurs have more diverse locomotor modes that probably have allowed them to live in more habitat types. As an evolutionary outcome, Francois＇ langurs have a larger distribution range .

Comparative Analysis of Five Different Homologous Feeder Cell Lines in the Ability to Support Rhesus Embryonic Stem Cells

In our previous study, five homologous feeder cell lines, Monkey ear skin fibroblasts （MESFs）, clonally derived fibroblasts from the MESFs （CMESFs）, monkey oviductal fibroblasts （MOFs）, monkey follicular granulosa fibroblast-like （MFGs） cells, monkey follicular granulosa epithelium-like （MFGEs） cells, were developed for the maintenance of rhesus embryonic stem cells （rESCs）. We found that MESFs, CMESFs, MOFs and MFGs, but not MFGEs, support the growth of rhesus embryonic stem cells. Moreover, we detected some genes that are upregulated in supportive feeder cell lines by semi-quantitative PCR. In the present study, we applied the GeneChip Rhesus Macaque Genome Array of Affymetrix Corporation to study the expression profiles of these five feeder cell lines, in purpose to find out which cytokines and signaling pathways were important in maintaining the rESCs, mRNAs of eight genes, including GREM2, bFGF, KITLG, DKK3, GREM1, AREG, SERPINF1 and LTBP1, were found to be upregulated in supportive feeder cell lines, but not in MFGE. The results indicate that many signaling pathways may play redundant roles in supporting the undifferentiated growth and maintenance of pluripotency in rESCs.

Practice and design of the self-purification system for heavy metals-bearing contaminants

Many minerals in nature have self-purification capacity to hold and stabilize deleterious contaminants into their lattice structures,which can be used for treatment of heavy metals-bearing contaminants. Hydrotalcite Layer Double Hydroxide (LDH),tobermorite Calcium Silicate Hydrate (CSH) and apatite are ubiquitous minerals in nature,having higher geochemical stability and potential for binding and stabilizing heavy metals. Based on the elucidation of crystal structure property and self-purification principles of the three minerals above,this article discussed how to design the self-purification system of heavy metal-bearing contaminants.