The present research is an experimental study on heat transfer characteristics of a natural circulation cooling system for electronic components. A smooth chip and two micro-pin-finned chips were tested. The chip is m...The present research is an experimental study on heat transfer characteristics of a natural circulation cooling system for electronic components. A smooth chip and two micro-pin-finned chips were tested. The chip is mounted on the base of a rectangular horizontal duct located at the bottom of 250 mm high natural circulation loop.FC-72 is used as a coolant. The test conditions are set that the operation pressure of experimental system is 1. 013× 105 Pa, the flow rate of FC-72 is 150 g/min and the subcoolings are 10 K, 25 K and 35 k, respectively. Effect of the subcooling on nucleate boiling and critical heat flux(CHF) were investigated. The results show that subcoolingis found to significantly affect CHF for all chips and micro-pin-finned chips sharply enhanced the boiling heat transfer, CHF of micro-pin-finned chips are 2.5～3 times as large as that of smooth chip at the same subcooling.展开更多
Free convection flow between two vertical parallel plates with transverse sinusoidal injection of the fluid at the stationary plate and its corresponding removal by constant suction through the plate in uniform motion...Free convection flow between two vertical parallel plates with transverse sinusoidal injection of the fluid at the stationary plate and its corresponding removal by constant suction through the plate in uniform motion has been analyzed. Due to this type of injection velocity, the flow becomes three-dimensional. Analytical expressions for the velocity, temperature, skin friction and rate of heat transfer were obtained. The important characteristics of the problem, namely the skin friction and the rate of heat transfer are discussed in detail with the help of graphs.展开更多
Paper deals about testing of device with gravity assisted heat pipes and about researching of wick heat pipes used to effective heat transfers from power switches of energy converter. At first, to simulate ambient con...Paper deals about testing of device with gravity assisted heat pipes and about researching of wick heat pipes used to effective heat transfers from power switches of energy converter. At first, to simulate ambient condition was designed thermostatic chamber where was monitoring temperature course on main parts of cooling device （energy converter, air cooler and heat pipes） at various position of cooling device. It was found, if the cooling device is in tilt position the cooling performance is better. But if the tilt angel of gravity assisted heat pipe is higher the heat transfer is lower. From reason improve heat transfer cooling device at tilt angle are manufactured heat pipes with the sintered, mesh screen and grooved capillary structures and tested their thermal performance at vertical and tilt angel 45~ position by calorimetric method. Article describes manufacturing process and thermal performance measuring method of wick heat pipes. This experiment testify that the wick heat pipe is able operate at tilt angle position than gravity assisted heat pipe and application of wick heat pipes into cooling device will improve his cooling performance.展开更多
Laminar natural convection heat transfer inside air-filled, rectangular enclosures partially heated from below and cooled at one side is studied numerically. A computational code based on the SIMPLE-C algorithm is use...Laminar natural convection heat transfer inside air-filled, rectangular enclosures partially heated from below and cooled at one side is studied numerically. A computational code based on the SIMPLE-C algorithm is used for the solution of the system of the mass, momentum, and energy transfer governing equations. Simulations are performed for a complete range of heater size, for Rayleigh numbers based on the height of the cavity ranging from 10~3to 10~6, and for height-to-width aspect ratios of the cavity spanning from 0.25 to 4. It is found that the heat transfer rate increases with increasing the heater size and the Rayleigh number, while it decreases with increasing the aspect ratio of the cavity. Dimensionless heat transfer correlations are also proposed.展开更多
We prove the convergence of an adaptive mixed finite element method(AMFEM) for(nonsymmetric) convection-diffusion-reaction equations. The convergence result holds for the cases where convection or reaction is not pres...We prove the convergence of an adaptive mixed finite element method(AMFEM) for(nonsymmetric) convection-diffusion-reaction equations. The convergence result holds for the cases where convection or reaction is not present in convection- or reaction-dominated problems. A novel technique of analysis is developed by using the superconvergence of the scalar displacement variable instead of the quasi-orthogonality for the stress and displacement variables, and without marking the oscillation dependent on discrete solutions and data. We show that AMFEM is a contraction of the error of the stress and displacement variables plus some quantity. Numerical experiments confirm the theoretical results.展开更多
文摘The present research is an experimental study on heat transfer characteristics of a natural circulation cooling system for electronic components. A smooth chip and two micro-pin-finned chips were tested. The chip is mounted on the base of a rectangular horizontal duct located at the bottom of 250 mm high natural circulation loop.FC-72 is used as a coolant. The test conditions are set that the operation pressure of experimental system is 1. 013× 105 Pa, the flow rate of FC-72 is 150 g/min and the subcoolings are 10 K, 25 K and 35 k, respectively. Effect of the subcooling on nucleate boiling and critical heat flux(CHF) were investigated. The results show that subcoolingis found to significantly affect CHF for all chips and micro-pin-finned chips sharply enhanced the boiling heat transfer, CHF of micro-pin-finned chips are 2.5～3 times as large as that of smooth chip at the same subcooling.
文摘Free convection flow between two vertical parallel plates with transverse sinusoidal injection of the fluid at the stationary plate and its corresponding removal by constant suction through the plate in uniform motion has been analyzed. Due to this type of injection velocity, the flow becomes three-dimensional. Analytical expressions for the velocity, temperature, skin friction and rate of heat transfer were obtained. The important characteristics of the problem, namely the skin friction and the rate of heat transfer are discussed in detail with the help of graphs.
文摘Paper deals about testing of device with gravity assisted heat pipes and about researching of wick heat pipes used to effective heat transfers from power switches of energy converter. At first, to simulate ambient condition was designed thermostatic chamber where was monitoring temperature course on main parts of cooling device （energy converter, air cooler and heat pipes） at various position of cooling device. It was found, if the cooling device is in tilt position the cooling performance is better. But if the tilt angel of gravity assisted heat pipe is higher the heat transfer is lower. From reason improve heat transfer cooling device at tilt angle are manufactured heat pipes with the sintered, mesh screen and grooved capillary structures and tested their thermal performance at vertical and tilt angel 45~ position by calorimetric method. Article describes manufacturing process and thermal performance measuring method of wick heat pipes. This experiment testify that the wick heat pipe is able operate at tilt angle position than gravity assisted heat pipe and application of wick heat pipes into cooling device will improve his cooling performance.
文摘Laminar natural convection heat transfer inside air-filled, rectangular enclosures partially heated from below and cooled at one side is studied numerically. A computational code based on the SIMPLE-C algorithm is used for the solution of the system of the mass, momentum, and energy transfer governing equations. Simulations are performed for a complete range of heater size, for Rayleigh numbers based on the height of the cavity ranging from 10~3to 10~6, and for height-to-width aspect ratios of the cavity spanning from 0.25 to 4. It is found that the heat transfer rate increases with increasing the heater size and the Rayleigh number, while it decreases with increasing the aspect ratio of the cavity. Dimensionless heat transfer correlations are also proposed.
基金supported by Education Science Foundation of Chongqing(Grant No.KJ120420)National Natural Science Foundation of China(Grant No.11171239)+1 种基金Major Research Plan of National Natural Science Foundation of China(Grant No.91430105)Open Fund of Key Laboratory of Mountain Hazards and Earth Surface Processes,Chinese Academy Sciences
文摘We prove the convergence of an adaptive mixed finite element method(AMFEM) for(nonsymmetric) convection-diffusion-reaction equations. The convergence result holds for the cases where convection or reaction is not present in convection- or reaction-dominated problems. A novel technique of analysis is developed by using the superconvergence of the scalar displacement variable instead of the quasi-orthogonality for the stress and displacement variables, and without marking the oscillation dependent on discrete solutions and data. We show that AMFEM is a contraction of the error of the stress and displacement variables plus some quantity. Numerical experiments confirm the theoretical results.
