This study investigates the resistance of a transport ship navigating in level ice by conducting a series of model tests in an ice tank at Tianjin University. The laboratory-scale model ship was mounted on a rigid car...This study investigates the resistance of a transport ship navigating in level ice by conducting a series of model tests in an ice tank at Tianjin University. The laboratory-scale model ship was mounted on a rigid carriage using a one-directional load cell and then towed through an ice sheet at different speeds. We observed the ice-breaking process at different parts of the ship and motion of the ice floes and measured the resistances under different speeds to determine the relationship between the ice-breaking process and ice resistance. The bending failure at the shoulder area was found to cause maximum resistance. Furthermore, we introduced the analytical method of Lindqvist （1989） for estimating ice resistance and then compared these calculated results with those from our model tests. The results indicate that the calculated total resistances are higher than those we determined in the model tests.展开更多
Ship hull form of the underwater area strongly influences the resistance of the ship. The major factor in ship resistance is skin friction resistance. Bulbous bows, polymer paint, water repellent paint （highly water-...Ship hull form of the underwater area strongly influences the resistance of the ship. The major factor in ship resistance is skin friction resistance. Bulbous bows, polymer paint, water repellent paint （highly water-repellent wall）, air injection, and specific roughness have been used by researchers as an attempt to obtain the resistance reduction and operation efficiency of ships. Micro-bubble injection is a promising technique for lowering frictional resistance. The injected air bubbles are supposed to somehow modify the energy inside the turbulent boundary layer and thereby lower the skin friction. The purpose of this study was to identify the effect of injected micro bubbles on a navy fast patrol boat （FPB） 57 m type model with the following main dimensions： L=2 450 ram, B=400 mm, and T=190 mm. The influence of the location of micro bubble injection and bubble velocity was also investigated. The ship model was pulled by an electric motor whose speed could be varied and adjusted. The ship model resistance was precisely measured by a load cell transducer. Comparison of ship resistance with and without micro-bubble injection was shown on a graph as a function of the drag coefficient and Froude number. It was shown that micro bubble injection behind the mid-ship is the best location to achieve the most effective drag reduction, and the drag reduction caused by the micro-bubbles can reach 6%-9%.展开更多
基金Supported by the National Natural Science Foundation of China under Grant Nos. 51179123 and 51279131
文摘This study investigates the resistance of a transport ship navigating in level ice by conducting a series of model tests in an ice tank at Tianjin University. The laboratory-scale model ship was mounted on a rigid carriage using a one-directional load cell and then towed through an ice sheet at different speeds. We observed the ice-breaking process at different parts of the ship and motion of the ice floes and measured the resistances under different speeds to determine the relationship between the ice-breaking process and ice resistance. The bending failure at the shoulder area was found to cause maximum resistance. Furthermore, we introduced the analytical method of Lindqvist （1989） for estimating ice resistance and then compared these calculated results with those from our model tests. The results indicate that the calculated total resistances are higher than those we determined in the model tests.
基金Supported by the Directorate for Research and Community Service,University of Indonesia(RUUI Research Laboratory 2010),Jakarta,Indonesia
文摘Ship hull form of the underwater area strongly influences the resistance of the ship. The major factor in ship resistance is skin friction resistance. Bulbous bows, polymer paint, water repellent paint （highly water-repellent wall）, air injection, and specific roughness have been used by researchers as an attempt to obtain the resistance reduction and operation efficiency of ships. Micro-bubble injection is a promising technique for lowering frictional resistance. The injected air bubbles are supposed to somehow modify the energy inside the turbulent boundary layer and thereby lower the skin friction. The purpose of this study was to identify the effect of injected micro bubbles on a navy fast patrol boat （FPB） 57 m type model with the following main dimensions： L=2 450 ram, B=400 mm, and T=190 mm. The influence of the location of micro bubble injection and bubble velocity was also investigated. The ship model was pulled by an electric motor whose speed could be varied and adjusted. The ship model resistance was precisely measured by a load cell transducer. Comparison of ship resistance with and without micro-bubble injection was shown on a graph as a function of the drag coefficient and Froude number. It was shown that micro bubble injection behind the mid-ship is the best location to achieve the most effective drag reduction, and the drag reduction caused by the micro-bubbles can reach 6%-9%.
