Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DS...Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DSC scan rate, and the step wise annealing on the melting peaks of the ice water quenched specimens. Results and Conclusion Varied melting peaks of PA6 component were obtained. The degree of perfection and the crystallization degree of PA6 crystals decreased in the blends, and the crystallization degree of PA6 increased with the increasing of the annealing time. The height of the upper melting peak of reference PA6 is higher than that in blends.展开更多
Aim To investigate the multiple melting behavior of polyamide 6(PA 6) in polyamide 6/linear low density polyethylene blends crystallized from the crystal amorphous state. Methods\ The effects of annealing tempera...Aim To investigate the multiple melting behavior of polyamide 6(PA 6) in polyamide 6/linear low density polyethylene blends crystallized from the crystal amorphous state. Methods\ The effects of annealing temperature, annealing time, heating rate, and the step wise annealing were measured by DSC. Results and Conclusion\ There exists a critical heating rate affecting the middle temperature melting peak. When annealed at the temperature close to the melting peak, the main melting peak of PA 6 shifted to a higher temperature. Within a short time, annealing time has much effect on neat PA 6 but little effect on PA 6 in the blends. Addition of PE results in a decreasing in the height of melting peak. These phenomenon show that the melting behavior of PA 6 was affected by PE, compatibilizer, as well as thermal treatment.展开更多
Polypropylene(PP)with different contents of the second generation hyperbranched polyester(HBP)is prepared by melt blending method.The non-isothermal crystallization kinetics of PP and PP/HBP blends is investigated und...Polypropylene(PP)with different contents of the second generation hyperbranched polyester(HBP)is prepared by melt blending method.The non-isothermal crystallization kinetics of PP and PP/HBP blends is investigated under differential scanning calorimetry(DSC).The Mo equation is used to analyze the DSC data.The results show that the Mo theory is suitable for crystallization kinetics of the blends.Fast cooling rate is not good for crystallizing and nucleating.The values of half crystallization time(t1/2),crystallization enthalpy(ΔHc)and temperature range(ΔT)of PP/HBP blends decrease when HBP is added.The required cooling rate of PP is higher than that of PP/HBP blends in order to reach the same relative crystallinity.Crystallization rate increases with the addition of HBP.The crystallization rate reaches a maximum when the content of HBP is 5%.In addition,the activation energies of PP and PP/HBP blends are calculated by Kissinger equation,revealing that the content of HBP has a little effect on the crystallization activation energy.展开更多
文摘Aim To investigate the melting behavior of polyamide 6 in polyamide 6/polyethy lene blends crystallized from amorphous state. Methods DSC was used to test effects of annealing temperature, annealing time, DSC scan rate, and the step wise annealing on the melting peaks of the ice water quenched specimens. Results and Conclusion Varied melting peaks of PA6 component were obtained. The degree of perfection and the crystallization degree of PA6 crystals decreased in the blends, and the crystallization degree of PA6 increased with the increasing of the annealing time. The height of the upper melting peak of reference PA6 is higher than that in blends.
文摘Aim To investigate the multiple melting behavior of polyamide 6(PA 6) in polyamide 6/linear low density polyethylene blends crystallized from the crystal amorphous state. Methods\ The effects of annealing temperature, annealing time, heating rate, and the step wise annealing were measured by DSC. Results and Conclusion\ There exists a critical heating rate affecting the middle temperature melting peak. When annealed at the temperature close to the melting peak, the main melting peak of PA 6 shifted to a higher temperature. Within a short time, annealing time has much effect on neat PA 6 but little effect on PA 6 in the blends. Addition of PE results in a decreasing in the height of melting peak. These phenomenon show that the melting behavior of PA 6 was affected by PE, compatibilizer, as well as thermal treatment.
基金Supported by the Youths Foundation of Wuhan Institute of Technology(Q200902)the Graduate Innovative Fund of Wuhan Institute of Technology(CX201101)
文摘Polypropylene(PP)with different contents of the second generation hyperbranched polyester(HBP)is prepared by melt blending method.The non-isothermal crystallization kinetics of PP and PP/HBP blends is investigated under differential scanning calorimetry(DSC).The Mo equation is used to analyze the DSC data.The results show that the Mo theory is suitable for crystallization kinetics of the blends.Fast cooling rate is not good for crystallizing and nucleating.The values of half crystallization time(t1/2),crystallization enthalpy(ΔHc)and temperature range(ΔT)of PP/HBP blends decrease when HBP is added.The required cooling rate of PP is higher than that of PP/HBP blends in order to reach the same relative crystallinity.Crystallization rate increases with the addition of HBP.The crystallization rate reaches a maximum when the content of HBP is 5%.In addition,the activation energies of PP and PP/HBP blends are calculated by Kissinger equation,revealing that the content of HBP has a little effect on the crystallization activation energy.
