In order to investigate the springback rules, the variation characteristics of physical property and microstructure in bending creep age forming process, a series of creep forming tests of 2124 aluminum alloy were con...In order to investigate the springback rules, the variation characteristics of physical property and microstructure in bending creep age forming process, a series of creep forming tests of 2124 aluminum alloy were conducted based on three kinds of single and double curvature forming tools. The results show that the spingback rate would be the minimum under the optimal coupling conditions among the temperature, aging time and internal stress state of material. Difference exists in the two directions of the formed sample with double curvature, but the curvature variation keeps the same. Yield strength, ultimate tensile strength and fracture toughness of the double curvature formed sample appear to be higher than those of the single curvature formed sample under the same aging condition, but the elongation and the anisotropy are opposite.展开更多
The bending deformation method was adopted to characterize the creep deformation behavior of Al-Cu-Li alloy in the creep aging forming(CAF) process based on a series of CAF tests, and the evolution laws of its mechani...The bending deformation method was adopted to characterize the creep deformation behavior of Al-Cu-Li alloy in the creep aging forming(CAF) process based on a series of CAF tests, and the evolution laws of its mechanical properties and microstructures under different pre-deformation conditions were studied. The results show that the bending creep strain characterization method can intuitively describe the creep variation. With the increase of the pre-deformation strain, the creep strain of the specimen firstly increases and then decreases. The increase of the pre-deformation strain can promote the course of aging precipitation, and improve the formed alloy’s tensile properties at room temperature, the Kahn tearing properties, and the fatigue propagation properties. Pre-rolled specimens produce a slightly weaker work hardening than pre-stretched specimens, but they also create a stronger aging-strengthening effect;thus the strength, toughness and damage performance can be improved to some extent. Among all the types of specimens, the specimen with 3% rolling after CAF treatment has the best comprehensive mechanical properties.展开更多
The density of asphalt was measured with the pycnometer and densitometer. Creep properties of the asphalt were investigated with the bending beam rheometer at temperatures ranging from 0 ~C to -36 ~C. The asphalt dens...The density of asphalt was measured with the pycnometer and densitometer. Creep properties of the asphalt were investigated with the bending beam rheometer at temperatures ranging from 0 ~C to -36 ~C. The asphalt density data used to correlate with the creep properties were calculated from the regression equation of density and temperature. The asphalt sample used to determine the creep property was aged by the standard RTFOT test and the PAV test. The test results showed that the asphalt density had a linear relationship with temperature changes. The logarithm of the creep stiffness and the slope of the logarithm of the stiffness at 60 seconds all demonstrated a linear relationship with the density, and the regression coefficient of these data was around 0.99. The creep stiffness and the slope of the creep stiffness can be calculated from the asphalt density at the same temperature.展开更多
基金Project(2010CB731700)supported by the National Basic Research Program of China
文摘In order to investigate the springback rules, the variation characteristics of physical property and microstructure in bending creep age forming process, a series of creep forming tests of 2124 aluminum alloy were conducted based on three kinds of single and double curvature forming tools. The results show that the spingback rate would be the minimum under the optimal coupling conditions among the temperature, aging time and internal stress state of material. Difference exists in the two directions of the formed sample with double curvature, but the curvature variation keeps the same. Yield strength, ultimate tensile strength and fracture toughness of the double curvature formed sample appear to be higher than those of the single curvature formed sample under the same aging condition, but the elongation and the anisotropy are opposite.
基金Project(2017YFB0306301)supported by the National Key Research and Development Program of ChinaProject(51705539)supported by the National Natural Science Foundation of China。
文摘The bending deformation method was adopted to characterize the creep deformation behavior of Al-Cu-Li alloy in the creep aging forming(CAF) process based on a series of CAF tests, and the evolution laws of its mechanical properties and microstructures under different pre-deformation conditions were studied. The results show that the bending creep strain characterization method can intuitively describe the creep variation. With the increase of the pre-deformation strain, the creep strain of the specimen firstly increases and then decreases. The increase of the pre-deformation strain can promote the course of aging precipitation, and improve the formed alloy’s tensile properties at room temperature, the Kahn tearing properties, and the fatigue propagation properties. Pre-rolled specimens produce a slightly weaker work hardening than pre-stretched specimens, but they also create a stronger aging-strengthening effect;thus the strength, toughness and damage performance can be improved to some extent. Among all the types of specimens, the specimen with 3% rolling after CAF treatment has the best comprehensive mechanical properties.
文摘The density of asphalt was measured with the pycnometer and densitometer. Creep properties of the asphalt were investigated with the bending beam rheometer at temperatures ranging from 0 ~C to -36 ~C. The asphalt density data used to correlate with the creep properties were calculated from the regression equation of density and temperature. The asphalt sample used to determine the creep property was aged by the standard RTFOT test and the PAV test. The test results showed that the asphalt density had a linear relationship with temperature changes. The logarithm of the creep stiffness and the slope of the logarithm of the stiffness at 60 seconds all demonstrated a linear relationship with the density, and the regression coefficient of these data was around 0.99. The creep stiffness and the slope of the creep stiffness can be calculated from the asphalt density at the same temperature.
