A 30Gbit/s receptor module is developed with a CMOS integrated receiver chip（IC） and a GaAs-based 1 × 12 photo detector array of PIN-type. Parallel technology is adopted in this module to realize a high-speed r...A 30Gbit/s receptor module is developed with a CMOS integrated receiver chip（IC） and a GaAs-based 1 × 12 photo detector array of PIN-type. Parallel technology is adopted in this module to realize a high-speed receiver module with medium speed devices. A high-speed printed circuit board（PCB） is designed and produced. The IC chip and the PD array are packaged on the PCB by chip-on-board technology. Flip chip alignment is used for the PD array accurately assembled on the module so that a plug-type optical port is built. Test results show that the module can receive parallel signals at 30Gbit/s. The sensitivity of the module is - 13.6dBm for 10^-13 BER.展开更多
An interesting phenomenon of cooling-rate induced brittleness in Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass （BMG） was reported. It was found that the as-cast BMG specimens exhibited a brittle-ductile transition w...An interesting phenomenon of cooling-rate induced brittleness in Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass （BMG） was reported. It was found that the as-cast BMG specimens exhibited a brittle-ductile transition when the larger specimens were machined into smaller specimens through removing the cast-softening surface layer by layer. After compression tests, the as-machined small specimens, owing to the absence of the cast-softening surface, displayed highly dense and intersecting shear bands, and extensive plastic deformation. This is in contrast to the catastrophic failure and low deformability in the as-cast large specimens. More free volume was detected in the smaller as-fractured specimens, by differential scanning calorimetry, which may be attributed to the occurrence of strain softening and increased plasticity. Compared with the relatively smooth fracture surface in the smaller specimens, the larger specimens showed more diverse features on the fracture surface due to their graded structures.展开更多
Aim To separate texts from graphics on mechanical engineering drawings. Methods By improved labeling run, the size of circumscribed rectangle and pixel density about the connected graphs on a drawing were gained,...Aim To separate texts from graphics on mechanical engineering drawings. Methods By improved labeling run, the size of circumscribed rectangle and pixel density about the connected graphs on a drawing were gained, according to these value, texts not sticking to graphics could be separated from a drawing. The concept of appendant block was introduced, using the appendant block, texts sticking to graphics could be determined and cut. Results Texts and symbols on mechanical engineering drawings can be separated well. Conclusion This method is simple and fast, it does not destroy the shape of texts and symbols, it can be used for separating texts and symbols from all linear graphics.展开更多
AIM:To evaluate the surgical outcomes following radical antegrade modular pancreatosplenectomy (RAMPS) for pancreatic cancer. METHODS:Twenty-four patients underwent RAMPS with curative intent between January 2005 and ...AIM:To evaluate the surgical outcomes following radical antegrade modular pancreatosplenectomy (RAMPS) for pancreatic cancer. METHODS:Twenty-four patients underwent RAMPS with curative intent between January 2005 and June 2009 at the National Cancer Center, South Korea. Clinicopathologic data, including age, sex, operative findings, pathologic results, adjuvant therapy, postop-erative clinical course and follow-up data were retro-spectively collected and analyzed for this study. RESULTS:Twenty-one patients (87.5%) underwent distal pancreatectomy and 3 patients (12.5%) underwent total pancreatectomy using RAMPS. Nine patients (37.5%) underwent combined vessel resection, including 8 superior mesenteric-portal vein resections and 1 celiac axis resection. Two patients (8.3%) underwent combined resection of other organs, including the colon, stomach or duodenum. Negative tangential margins were achieved in 22 patients (91.7%). The mean tumor diameter for all patients was 4.09 ± 2.15 cm. The 2 patients with positive margins had a mean diameter of 7.25 cm. The mean number of retrieved lymph nodes was 20.92 ± 11.24 and the node positivity rate was 70.8%. The median survival of the 24 patients was 18.23 ± 6.02 mo. Patients with negative margins had a median survival of 21.80 ± 5.30 mo and those with positive margins had a median survival of 6.47 mo (P = 0.021). Nine patients (37.5%) had postoperative complications, but there were no postoperative mortalities. Pancreatic fistula occurred in 4 patients (16.7%):2 patients had a grade A fistula and 2 had a grade B fistula. On univariate analysis, histologic grade, positive tangential margin, pancreatic fistula and adjuvant therapy were significant prognostic factors for survival. CONCLUSION:RAMPS is a feasible procedure for achieving negative tangential margins in patients with carcinoma of the body and tail of the pancreas.展开更多
Business needs to manage such a variety of things inside the firm or outside the business consistently. This factor affects the business in various ways. The factor which affects the business is clients, suppliers, di...Business needs to manage such a variety of things inside the firm or outside the business consistently. This factor affects the business in various ways. The factor which affects the business is clients, suppliers, distributors and so on. These all components are isolated from two sections full-scale environment and miniaturized scale environment. Macro perspective environment components are those external variables which are past the association＇s control. The problem of this study is guaranteeing a supportable evolvement of human presence in its social, ecological, and monetary measurement. So, we have to adapt test in order to outfit toward manageability. As for the method used in this study, it depends on using empirical framework to meet the interest of capital and buyer, in addition to supporting human presence in its social, ecological, monetary measurement. The paper is organised as following sections： first section is the introduction, second section is the literature review, the third section includes the research method, fourth one discusses the analysis, while the conclusion is in the fifth section.展开更多
文摘A 30Gbit/s receptor module is developed with a CMOS integrated receiver chip（IC） and a GaAs-based 1 × 12 photo detector array of PIN-type. Parallel technology is adopted in this module to realize a high-speed receiver module with medium speed devices. A high-speed printed circuit board（PCB） is designed and produced. The IC chip and the PD array are packaged on the PCB by chip-on-board technology. Flip chip alignment is used for the PD array accurately assembled on the module so that a plug-type optical port is built. Test results show that the module can receive parallel signals at 30Gbit/s. The sensitivity of the module is - 13.6dBm for 10^-13 BER.
基金Project(2012M511401)supported by China Postdoctoral Science FoundationProject(12JJ5018)supported by Hunan Provincial Natural Science Foundation of China+1 种基金Project(2012RS4006)supported by Hunan Provincial Science and Technology Plan of ChinaProject(CSUZC2012028)supported by the Open-End Fund for the Valuable and Precision Instruments of Central South University,China
文摘An interesting phenomenon of cooling-rate induced brittleness in Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass （BMG） was reported. It was found that the as-cast BMG specimens exhibited a brittle-ductile transition when the larger specimens were machined into smaller specimens through removing the cast-softening surface layer by layer. After compression tests, the as-machined small specimens, owing to the absence of the cast-softening surface, displayed highly dense and intersecting shear bands, and extensive plastic deformation. This is in contrast to the catastrophic failure and low deformability in the as-cast large specimens. More free volume was detected in the smaller as-fractured specimens, by differential scanning calorimetry, which may be attributed to the occurrence of strain softening and increased plasticity. Compared with the relatively smooth fracture surface in the smaller specimens, the larger specimens showed more diverse features on the fracture surface due to their graded structures.
文摘Aim To separate texts from graphics on mechanical engineering drawings. Methods By improved labeling run, the size of circumscribed rectangle and pixel density about the connected graphs on a drawing were gained, according to these value, texts not sticking to graphics could be separated from a drawing. The concept of appendant block was introduced, using the appendant block, texts sticking to graphics could be determined and cut. Results Texts and symbols on mechanical engineering drawings can be separated well. Conclusion This method is simple and fast, it does not destroy the shape of texts and symbols, it can be used for separating texts and symbols from all linear graphics.
文摘AIM:To evaluate the surgical outcomes following radical antegrade modular pancreatosplenectomy (RAMPS) for pancreatic cancer. METHODS:Twenty-four patients underwent RAMPS with curative intent between January 2005 and June 2009 at the National Cancer Center, South Korea. Clinicopathologic data, including age, sex, operative findings, pathologic results, adjuvant therapy, postop-erative clinical course and follow-up data were retro-spectively collected and analyzed for this study. RESULTS:Twenty-one patients (87.5%) underwent distal pancreatectomy and 3 patients (12.5%) underwent total pancreatectomy using RAMPS. Nine patients (37.5%) underwent combined vessel resection, including 8 superior mesenteric-portal vein resections and 1 celiac axis resection. Two patients (8.3%) underwent combined resection of other organs, including the colon, stomach or duodenum. Negative tangential margins were achieved in 22 patients (91.7%). The mean tumor diameter for all patients was 4.09 ± 2.15 cm. The 2 patients with positive margins had a mean diameter of 7.25 cm. The mean number of retrieved lymph nodes was 20.92 ± 11.24 and the node positivity rate was 70.8%. The median survival of the 24 patients was 18.23 ± 6.02 mo. Patients with negative margins had a median survival of 21.80 ± 5.30 mo and those with positive margins had a median survival of 6.47 mo (P = 0.021). Nine patients (37.5%) had postoperative complications, but there were no postoperative mortalities. Pancreatic fistula occurred in 4 patients (16.7%):2 patients had a grade A fistula and 2 had a grade B fistula. On univariate analysis, histologic grade, positive tangential margin, pancreatic fistula and adjuvant therapy were significant prognostic factors for survival. CONCLUSION:RAMPS is a feasible procedure for achieving negative tangential margins in patients with carcinoma of the body and tail of the pancreas.
文摘Business needs to manage such a variety of things inside the firm or outside the business consistently. This factor affects the business in various ways. The factor which affects the business is clients, suppliers, distributors and so on. These all components are isolated from two sections full-scale environment and miniaturized scale environment. Macro perspective environment components are those external variables which are past the association＇s control. The problem of this study is guaranteeing a supportable evolvement of human presence in its social, ecological, and monetary measurement. So, we have to adapt test in order to outfit toward manageability. As for the method used in this study, it depends on using empirical framework to meet the interest of capital and buyer, in addition to supporting human presence in its social, ecological, monetary measurement. The paper is organised as following sections： first section is the introduction, second section is the literature review, the third section includes the research method, fourth one discusses the analysis, while the conclusion is in the fifth section.
