Chemical Manganese Dioxide （CMD） was prepared by an alkali-oxidation method. There are several virtues to this environmental friendly and clean process, including the nontoxic and harmless reagents and products, eas...Chemical Manganese Dioxide （CMD） was prepared by an alkali-oxidation method. There are several virtues to this environmental friendly and clean process, including the nontoxic and harmless reagents and products, easy operations, no pollutants, easily obtained raw materials and moderate reaction conditions. The synthesized manganese dioxide was characterized by XRD and SEM. The particles were small, consisting primarily of α-MnO2 and γ-MnO2. Experimental results showed that the optimum conditions were： MnSOa.H20 to NaOH ratio, 1.0：2.4; catalyst concentration （catalyst TF-2）, 6% of the MnSO4; initial solution pH, 11; reaction time and temperature, 20 min and 80 ℃; air flow, 0.20 m3/h; and, agitation rate, 700 r/rain. The conversion of MnSO4 can exceed 80% under these optimum conditions.展开更多
The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase...The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase was detected by electron diffraction for samples aged below 400 ℃. The fine a aggregates are uniformly formed within fl grains by nucleating at the to particles or β/ω interfaces. At higher temperature, the formation of to phase is avoided and the a lamellae are precipitated at the preferred site of grain boundary and then within the matrix. The highest hardness values are found when the alloys are aged at 450 ℃ for fl condition and 350 ℃ for （α＋β） condition.展开更多
The molybdenum powders with average particle size of 3 μm were coated with copper by electroless plating. The influence of pretreatment, solution composition and plating conditions on electroless copper plating was s...The molybdenum powders with average particle size of 3 μm were coated with copper by electroless plating. The influence of pretreatment, solution composition and plating conditions on electroless copper plating was studied. The copper-coated molybdenum powders were examined by SEM and XRD. Results indicate that a series of optimization methods is used to add activated sites before electroless copper plating. Taking TEA and EDTA as chief and assistant complex agents respectively, 2,2＇-bipyridyl and PEG as double stabilizers, the Mo powders are coated with copper successfully with little Cu20 contained, at the same time, Mo-Cu composite powders with copper content of 15 - 85 wt% can be obtained. The optimal values of pH, temperature and HCHO concentration are 12 -13, 60 -65 ℃ and 22 -26 mL/L, respectively.展开更多
Grout plays an important role in the transmission and maintenance of anchoring force,and in the protection of anchorage materials against corrosion.Thus,the hardening characteristics of grout directly affect the ancho...Grout plays an important role in the transmission and maintenance of anchoring force,and in the protection of anchorage materials against corrosion.Thus,the hardening characteristics of grout directly affect the anchoring effectivity and long-term reliability.We have excavated a prestressed anchorage which has been in service for 20 years,and have tested the grout which has worked for that long period under complicated geological conditions through strength tests and have analyzed its mineral composition using scanning electron microscopy(SEM) and X-ray diffraction(XRD).The results show that the mineral composition of the 12.5 m segment differs from other segments,and corresponds with poor coagulation characteristics of the 12.5 m segment grout.Analysis shows that unhydrated tricalcium silicate may be the reason for the localized poor coagulation.展开更多
The influence of sintering temperature, carbon content and dispersive agent in bail-milling was investigated on the properties of LiFePO4/C prepared using Fe2O3, NH4H2PO4, Li2CO3 and glucose via solid state reaction. ...The influence of sintering temperature, carbon content and dispersive agent in bail-milling was investigated on the properties of LiFePO4/C prepared using Fe2O3, NH4H2PO4, Li2CO3 and glucose via solid state reaction. X-ray powder diffraction, scanning electron microscopy and charge-discharge test were applied to the characterization of the LiFePO4/C samples synthesized under different conditions. Sintering temperature affects the crystallite/ particle size and degree ofcrystallinity of LiFePO4, formation of Fe2P and maintenance of carbon in LiFePO4/C. Car- bon maintenance is favored by low sintering temperature, and 700 ℃ is optimum for synthesis of LiFePO4/C with superior electrochemical performance. A higher carbon content in the range of 4.48%-11.03% results in a better rate capability for LiFePO4/C. The dispersive agent used in ball-milling impacts the existent state of carbon in the final product which subsequently determines its charge-discharge behavior. The sample prepared at 700 ℃ by using acetone as the dispersive agent in ball-milling exhibits an excellent rate capability and capacity retention without any fade at 0.1 C, 1C and 2C, with corresponding average discharge capacities of 153.8, 128.3 and 121.0 mA·h·g-1. rest2ectivelv, in the first 50 cvcles.展开更多
Micaceous iron oxide （MIO） with a hexagonal flaky shape was prepared by hydrothermal method. The ferric hydroxide used as precursor was obtained by an acidic leaching solution of pyrite cinders reacting with ammonia...Micaceous iron oxide （MIO） with a hexagonal flaky shape was prepared by hydrothermal method. The ferric hydroxide used as precursor was obtained by an acidic leaching solution of pyrite cinders reacting with ammonia solution. The optimal experimental conditions for preparing micaceous iron oxide were investigated by orthogonal experiments. Micaceous iron oxide can be successfully prepared when optimal parameters of total iron concentration of 2.0 mol/L, pH value of 8, n（Fe2＋）/n（Fe3＋） of 0.1, mass of seed crystal of 1 g, reaction temperature of 260 ℃ and reaction time of 30 min are applied. X-ray diffractometry （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and selected area electron diffractometry （SAEM） were adopted to characterize the hydrothermal products prepared under optimal conditions. The results indicate that highly crystallized α-Fe2O3 hexagonal flakes, about 1.0-1.5 μm in diameter and 0.1 μm in thickness, are prepared. Furthermore, the quality of micaceous iron oxide prepared can meet the required characteristics of micaceous iron oxide pigments for paints （ISO 10601--2007）.展开更多
Enantiomers （R （＋） and S（-））, RS-racemate mixture of enantiomers） of malic acid C4H605 have been （double compound） and （R ＋ S） -conglomerate （mechanical investigated by means of X-ray diffractometry and ...Enantiomers （R （＋） and S（-））, RS-racemate mixture of enantiomers） of malic acid C4H605 have been （double compound） and （R ＋ S） -conglomerate （mechanical investigated by means of X-ray diffractometry and high tern- perature X-ray diffraction method. The RS-racemate was found to be able to form three polymorphic modifications, which we denominated as M1 （monoclinic, space group P21/c）, M2 （monoclinic, space group Cc）, and Tc （triclinic, space group P-l ）, the latter modification having been unknown before. Modification Tc was also described, and its X- ray diffraction characteristics, including interplanar spacings d, hkl indices, unit cell parameters, were defined. In addi- tion, X-ray diffraction characteristics for both reported earlier M1 and M2 monoclinic polymorphic modifications were measured with higher accuracy. The ability of RS-racemate to form one of the above three modifications （MI, M2, and Tc） or their mixtures containing various proportions and combinations of the components （M1 ＋ M2, M1 ＋ Tc, or M2 ＋ Tc） was found to depend on the type of crystallization medium （a melt, aqueous medium, ethanol or acetone solu- tion）, crystallization rate （from 2--3 minutes to 4 months）, and crystallization temperature. Heating S-enantiomer and M1 RS-racemate up to their respective melting points （100 ℃ and 124 ℃, correspondingly） only made them undergo thermal deformations, while heating （R ＋ S） -conglomerate in the temperature range of 96--110 ℃ resulted in its homogenization to form M2 RS-racemate, which, near the melting point （118 ℃）, namely, in the range of 112-116 ℃, was transformed into MI RS-racemate. Keywords： polvmorDhism; racemic, chiral展开更多
基金National Natural Science Foundation of China (No50704036)the Natural Science Foundation of Hunan Province (No08JJ3027) for their financial support
文摘Chemical Manganese Dioxide （CMD） was prepared by an alkali-oxidation method. There are several virtues to this environmental friendly and clean process, including the nontoxic and harmless reagents and products, easy operations, no pollutants, easily obtained raw materials and moderate reaction conditions. The synthesized manganese dioxide was characterized by XRD and SEM. The particles were small, consisting primarily of α-MnO2 and γ-MnO2. Experimental results showed that the optimum conditions were： MnSOa.H20 to NaOH ratio, 1.0：2.4; catalyst concentration （catalyst TF-2）, 6% of the MnSO4; initial solution pH, 11; reaction time and temperature, 20 min and 80 ℃; air flow, 0.20 m3/h; and, agitation rate, 700 r/rain. The conversion of MnSO4 can exceed 80% under these optimum conditions.
基金Project (50634030) supported by the National Natural Science Foundation of ChinaProject (2007DS04014) supported by the Program of Science and Technology of Shandong Province,ChinaProject supported by the Open Research Fund from the State Key Laboratory of Rolling and Automation,Northeastern University, China
文摘The evolution of microstructure on aging of an （α＋β） titanium alloy （Ti-5A1-5Mo-5V-1Cr-1Fe） in the β and （α＋β） solution-treated and quenched conditions was investigated, The presence of very fine to phase was detected by electron diffraction for samples aged below 400 ℃. The fine a aggregates are uniformly formed within fl grains by nucleating at the to particles or β/ω interfaces. At higher temperature, the formation of to phase is avoided and the a lamellae are precipitated at the preferred site of grain boundary and then within the matrix. The highest hardness values are found when the alloys are aged at 450 ℃ for fl condition and 350 ℃ for （α＋β） condition.
基金Sponsored by the National Natural Science Founation of China(Grant No.50301017)
文摘The molybdenum powders with average particle size of 3 μm were coated with copper by electroless plating. The influence of pretreatment, solution composition and plating conditions on electroless copper plating was studied. The copper-coated molybdenum powders were examined by SEM and XRD. Results indicate that a series of optimization methods is used to add activated sites before electroless copper plating. Taking TEA and EDTA as chief and assistant complex agents respectively, 2,2＇-bipyridyl and PEG as double stabilizers, the Mo powders are coated with copper successfully with little Cu20 contained, at the same time, Mo-Cu composite powders with copper content of 15 - 85 wt% can be obtained. The optimal values of pH, temperature and HCHO concentration are 12 -13, 60 -65 ℃ and 22 -26 mL/L, respectively.
基金supported by National Key Technology R&D Program during the 11th Five-Year Plan Perio(Grant NO. 2008BAB29B01)State Key Program of National Natural Science of China(Grant NO. 41130745)Research foundation of the State Key Laboratory of Geohazard Prevention & Geoenvironment Protection (Grant NO.SKLGP2010Z008)
文摘Grout plays an important role in the transmission and maintenance of anchoring force,and in the protection of anchorage materials against corrosion.Thus,the hardening characteristics of grout directly affect the anchoring effectivity and long-term reliability.We have excavated a prestressed anchorage which has been in service for 20 years,and have tested the grout which has worked for that long period under complicated geological conditions through strength tests and have analyzed its mineral composition using scanning electron microscopy(SEM) and X-ray diffraction(XRD).The results show that the mineral composition of the 12.5 m segment differs from other segments,and corresponds with poor coagulation characteristics of the 12.5 m segment grout.Analysis shows that unhydrated tricalcium silicate may be the reason for the localized poor coagulation.
基金Supported by the Natural Science Foundation of Yunnan Province(2010ZC051)the Analysis and Testing Foundation(20140439)the Starting Research Fund from Kunming University of Science and Technology(14118245)
文摘The influence of sintering temperature, carbon content and dispersive agent in bail-milling was investigated on the properties of LiFePO4/C prepared using Fe2O3, NH4H2PO4, Li2CO3 and glucose via solid state reaction. X-ray powder diffraction, scanning electron microscopy and charge-discharge test were applied to the characterization of the LiFePO4/C samples synthesized under different conditions. Sintering temperature affects the crystallite/ particle size and degree ofcrystallinity of LiFePO4, formation of Fe2P and maintenance of carbon in LiFePO4/C. Car- bon maintenance is favored by low sintering temperature, and 700 ℃ is optimum for synthesis of LiFePO4/C with superior electrochemical performance. A higher carbon content in the range of 4.48%-11.03% results in a better rate capability for LiFePO4/C. The dispersive agent used in ball-milling impacts the existent state of carbon in the final product which subsequently determines its charge-discharge behavior. The sample prepared at 700 ℃ by using acetone as the dispersive agent in ball-milling exhibits an excellent rate capability and capacity retention without any fade at 0.1 C, 1C and 2C, with corresponding average discharge capacities of 153.8, 128.3 and 121.0 mA·h·g-1. rest2ectivelv, in the first 50 cvcles.
基金Project(2008A090300016) supported by Major Science & Technology Special Program of Guangdong Province,China
文摘Micaceous iron oxide （MIO） with a hexagonal flaky shape was prepared by hydrothermal method. The ferric hydroxide used as precursor was obtained by an acidic leaching solution of pyrite cinders reacting with ammonia solution. The optimal experimental conditions for preparing micaceous iron oxide were investigated by orthogonal experiments. Micaceous iron oxide can be successfully prepared when optimal parameters of total iron concentration of 2.0 mol/L, pH value of 8, n（Fe2＋）/n（Fe3＋） of 0.1, mass of seed crystal of 1 g, reaction temperature of 260 ℃ and reaction time of 30 min are applied. X-ray diffractometry （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and selected area electron diffractometry （SAEM） were adopted to characterize the hydrothermal products prepared under optimal conditions. The results indicate that highly crystallized α-Fe2O3 hexagonal flakes, about 1.0-1.5 μm in diameter and 0.1 μm in thickness, are prepared. Furthermore, the quality of micaceous iron oxide prepared can meet the required characteristics of micaceous iron oxide pigments for paints （ISO 10601--2007）.
基金Supported by the Russian Fund for Basic Research (RFBR) under Grant No. 10-05-00891 and 12-05-00876
文摘Enantiomers （R （＋） and S（-））, RS-racemate mixture of enantiomers） of malic acid C4H605 have been （double compound） and （R ＋ S） -conglomerate （mechanical investigated by means of X-ray diffractometry and high tern- perature X-ray diffraction method. The RS-racemate was found to be able to form three polymorphic modifications, which we denominated as M1 （monoclinic, space group P21/c）, M2 （monoclinic, space group Cc）, and Tc （triclinic, space group P-l ）, the latter modification having been unknown before. Modification Tc was also described, and its X- ray diffraction characteristics, including interplanar spacings d, hkl indices, unit cell parameters, were defined. In addi- tion, X-ray diffraction characteristics for both reported earlier M1 and M2 monoclinic polymorphic modifications were measured with higher accuracy. The ability of RS-racemate to form one of the above three modifications （MI, M2, and Tc） or their mixtures containing various proportions and combinations of the components （M1 ＋ M2, M1 ＋ Tc, or M2 ＋ Tc） was found to depend on the type of crystallization medium （a melt, aqueous medium, ethanol or acetone solu- tion）, crystallization rate （from 2--3 minutes to 4 months）, and crystallization temperature. Heating S-enantiomer and M1 RS-racemate up to their respective melting points （100 ℃ and 124 ℃, correspondingly） only made them undergo thermal deformations, while heating （R ＋ S） -conglomerate in the temperature range of 96--110 ℃ resulted in its homogenization to form M2 RS-racemate, which, near the melting point （118 ℃）, namely, in the range of 112-116 ℃, was transformed into MI RS-racemate. Keywords： polvmorDhism; racemic, chiral
