纳米催化剂Pt/C的X射线衍射线形分析

X射线衍射线形与晶体材料的微观结构密切相关.在晶粒尺寸衍射线形和微应变衍射线形可由Voigt函数近似描述的前提下,本文较详细地论述了由X射线衍射线形分析获取晶粒尺寸和位错等微观结构信息的方法.采用这种方法,对乙二醇还原法制备的Pt/C催化剂进行了X射线衍射线形分析.样品晶粒尺寸分布的对数正态均值为0.95 nm,对数正态方差为0.37.X射线衍射线形分析所得晶粒尺寸分布与透射电镜的测试结果符合较好.对样品的衍射线形积分宽度进行细致的比较,发现存在各向异性展宽现象.如果衍射线的各向异性展宽主要是由伯格斯矢量为1/2〈110〉的位错引起,可进一步计算位错密度值.结果表明,位错组态无论是螺型位错还是刃型位错,位错密度值的量级均约为1015/m2.

材料中晶粒尺寸及微观畸变对X衍射线形的影响

讨论了引起X衍射线形宽化的几种因素 ,以及材料中晶粒尺寸的大小、微观畸变与X衍射线形的关系 。

X射线衍射线形Fourier变换

采用计算机辅助实验技术，研究Ｘ射线衍射线形在仪器宽化修正过程中Ｆｏｕｒｉｅｒ系数变化的规律及其影响 ．结果表明，只要实测线形接近 Ｇａｕｓｓ分布，Ｆｏｕｒｉｅｒ变换就会导致弯勾效应； Ｆｏｕｒｉｅｒ变换可引起真实线形的尾部波动及大于实际值的宽化，引入边界条件可予以消除：Ｋａ双线线形经过 Ｆｏｕｒｉｅｒ变换后，Ｆｏｕｒｉｅｒ系数与真实 Ｆｏｕｒｉｅｒ系数存在着一定的差异，通过真实线形的 Ｆｏｕｒｉｅｒ变换可以修正．

铜薄膜微结构的X射线衍射线形分析

首先采用真空蒸镀法制备了不同厚度的铜薄膜,并对薄膜进行了退火处理;然后用X射线衍射仪测定铜薄膜的衍射谱,最后采用线形分析法对衍射谱进行计算,得到了不同厚度铜薄膜退火前后的晶粒尺寸和微应变。结果表明:真空蒸镀铜薄膜晶粒尺寸随薄膜厚度的增加而增大,微应变随薄膜厚度的增加而减小;退火处理后薄膜晶粒明显长大,薄膜微应变在退火处理后明显减小。

基于X射线衍射线形分析的铝合金切削表层晶体特征研究

为深入研究高速高效加工条件下材料表层晶体特征形成机理,提高铝合金构件服役性能,同时解决传统观察法较难得出晶粒尺寸与位错密度统计学规律的问题,立足微观,以铝合金7050-T7451为研究对象,将材料学与物理学中基于X射线衍射线形分析的Modified Warren-Averbach和Modified Williamson-Hall方法引入切削加工表层微观组织分析中,实现了不同切削速度下切削表层微观组织结构的定量研究。研究表明,高速切削条件下已加工表面以刃位错为主,得出了位错密度值(高达1015 m-2以上)与位错密度变化规律,并从塑性变形及能量角度解释了其形成机理;拟合出了晶粒尺寸分布曲线,并通过分布函数分析了已加工表面晶粒分布均匀性;当切削速度高于4500m/min时可以得到位错密度相对较低、晶体尺寸较均匀的已加工表面。

近似函数法衍射线形测算规范化研究

为增强衍射线形测算的近似函数法的适用性,该法中某些手段有待于改进和规范化。本文探讨了该法中衍射峰背底扣除的准确方法;分析了Rachinger法分离出的Kα_1峰高角侧半峰曲线波动的规律及原因;推荐了严格计算物理宽化函数积分宽度的方法。

拟薄水铝石结构的演化

以理学D/max -3BX射线衍射仪、TG -DTA、IR -4 4 0红外光谱等方法 ,研究了拟薄水铝石结构的演化。将拟薄水铝石视为一个演化系列 ,随着层间结构水的变化 ,导致结构由非晶态至晶态、无序向有序的演化。研究了衍射峰线形宽化、〔0 2 0〕d值位移、晶粒度、吸热效应、羟基振动等变化规律 ,进而提出了拟薄水铝石的结构为〔AlOOH〕·nH2 O ,n为 0 0 80～ 0 6 0 2。

Microbially induced deposition of barium phosphates and its ingredient,morphology and size under different pH values

A phosphate-mineralization microbe was used to induce barium phosphates precipitation, and the precipitates with different types were obtained under different pH values. The average crystallite size of the barium phosphates was calculated by particle size distribution curves, and the size of the products was 33.40, 29. 37, 24. 13, 47.76 and 96. 53 μm when the pH values of the mixed solution are 7, 8, 9, 10 and 11, respectively. The results of X-ray diffraction （XRD） show that the structures of the particles controlled by the mixed solution are mainly BaaPO4 when pH 〈 10; the barium phosphates are synthesized by biological deposition which is the mixture of BaHPO4 and Ba5 （PO4）3OH when pH = 10; when pH = 11, the barium phosphates are also the mixtures, which are Ba5 （PO4）3OH and BaNaPO4. The above results indicate that the phosphate-mineralization microbe can produce a certain enzyme which constantly hydrolyzes phosphate monoester in the mixed solution, and then PO4^3- ions are obtained.

Preparation of titanium powders by calciothermic reduction of titanium dioxide

To develop an effective process for titanium powders production, a calciothermic reduction process of pigment titanium dioxide （w（TiO2）〉98%）, based on the preform reduction process （PRP）, was investigated by means of XRD, SEM and EDS. In this process, the mixture of TiO2 powder and CaC12 was pressed into pieces as feed preform and was reduced by calcium vapor. Titanium powders was recovered after leaching from the reduced preform with hydrochloric acid and deionized water. The results indicate when the mass ratio of CaC12 to TiO2 is about 1：4 and at a constant temperature of 1 273 K for 6 h in vacuum furnace, titanium powders with 99.55% purity by EDS analysis and irregular shape （8-15 μm in particle size） are obtained.

X-ray peak profile analysis of dislocation type,density and crystallite size distribution in cold deformed Pb-Ca-Sn alloys

The density,nature of the dislocations and distribution of the domain sizes in cold-deformed Pb-Ca-Sn solid solution were determined by X-ray diffraction profile analysis.The dislocation densities are of the order of 1010 cm-2.The strain broadening of diffraction profiles was accounted for by dislocation contrast factor.The coherent domain size was determined by the recently developed PM2K software package.Assuming that the domain size distribution is log-normal,the distribution function（median μ and variance σ） was calculated from the size parameters determined from X-ray diffraction profile analysis.

Micromorphological Aspects of Two Forest Soils Development Derived from Igneous Rocks in Lahijan, Iran

In order to characterize various micromorphologic properties of two forest soils derived from different parent rocks in Lahijan, and use the data collected from micromorphological analysis to interpret dominant pedogenic processes. Two representative soil pedons, granite （P1） and andesitic basalt （P2） were selected in a mountain landform with northwest aspect. Samples for thin section preparation were taken from each horizon by Kubiena boxes or clods. Micromorphological analysis of soils derived from these two soil pedons in eastern part of Lahijan （northern Iran） were conducted based on the physicochemical and mineralogical data. Micromorphological properties were characterized using a polarized light microscope under plain and cross light. Thin section study indicated that the nature of the parent material clearly affected the content of clay formation. It also showed that clay accumulation in the Bt horizons was not only due to clay illuviation （argillan）, but that strong in situ weathering of primary minerals also contributed to the enrichment of clay in soils derived from andesitic basalt. Comparing the results of clay mineralogy obtained from X-ray diffraction （XRD） with microscopic studies revealed that birefringence fabric （b-fabric） of the groundmass was partly striated due to smectitic minerals in soil of andesitic basalt （Hapludalf）, whereas speckled birefringence fabric was dominant in soil of granite （Udorthent） because of the absence of these minerals. We speculate that pores of skeletal fragments or microcracks in P1 were a place for illuvial clay protection. However, the main factor for flluvial clay film disruption （striation anddeformation） was biological activity （faunal turbation and root pressure） in P1 and expandable minerals and faunal turbation in P2.

Thermal stability evaluation of nanostructured Al6061 alloy produced by cryorolling

Grain growth of nanostructured Al6061produced by cryorolling and aging process was investigated during isothermalheat treatment in100?500°C temperature range.Transmission electron microscopy(TEM)observations demonstrate that aftercryorolling and aging at130°C for30h,the microstructure contains61nm grains with dispersed50?150nm precipitates and0.248%lattice strain.In addition,an increase in tensile strength up to362MPa because of formation of fine strengtheningprecipitation and nano-sized grains was observed.Thermal stability investigation within100?500°C temperature range showedrelease of lattice strain,dissolution of precipitates and grain growth.According to the X-ray diffraction(XRD)analysis,Mg2Siprecipitates disappeared after annealing at temperatures higher than300°C.According to the results,due to the limited grain growthup to200°C,there would be little decrease in mechanical properties,but within300?500°C range,the grain growth,dissolution ofstrengthening precipitates and decrease in mechanical properties are remarkable.The activation energies for grain growth werecalculated to be203.3kJ/mol for annealing at100?200°C and166.34kJ/mol for annealing at300?500°C.The effect ofprecipitation dissolution on Al lattice parameter,displacement of Al6061(111)XRD peak and Portevin?LeChatelier(PLC)effect onstress?strain curves is also discussed.

Hot-compression behavior of Al-1Mn-1Mg alloy

The hot-compression of Al-IMn-IMg （mass fraction, %） alloy sample was carried out on a Gleeble-1500 thermo-simulator at deformation temperatures from 320 to 400 ℃ and strain rates from 0.1 to 10 s 1 by total strain of 1.4. Microstructure and texture evolution of the hot-compressed alloy were investigated by optical microscopy and X-ray diffraction analysis, respectively. The results show that the relationship among flow stress a, deformation temperature T and strain rate ε can be expressed in the form of βσ = lnε＋Q/（RT）-lnA. The threshold value of In Z （Z is Zener-Hollomon parameter） characterizing the dynamic recrystallization （DRX） is 46, below which the DRX takes place. A strong P orientation {011}（455） associated with a weak cube orientation { 100} （001） is found in the recrystallized sample during hot-compression.

Preparation of ZAO film by low-temperature hydrothermal approach and its electrical property

Al-doped ZnO (ZAO) films were successfully deposited on the surface of common glasses by using low-temperature hydrothermal approach. In the reaction solution, the molar ratio of Al3+ to Zn2+ was 1∶100, the annealing temperature and time were 200 ℃ and 2-6 h, respectively. The structure of the thin films was identified by X-ray diffraction (XRD), the surface morphology and thickness of the thin films were observed by scanning electron microscopy (SEM), and the electrical performance of the thin films was measured by four-point probes. It was shown that the films with an average particle size of 27.53 nm had a preferential orientation along (002), Al3+ had replaced the position of Zn2+ in the lattice without forming the Al2O3 phase and its thickness was 20-25 μm. With the increased annealing time, the intensity of diffraction peaks was decreased, the film exhibited irregular surface morphology gradually, and the resistivity of ZAO films was increased. The lowest resistivity obtained in this study was 3.45×10-5Ω·cm.

Development of 3D crystallographic orientation measurement for grain deformation analysis in aluminum alloy

Development of inhomogeneous deformation is an interest matter in material engineering. Synchrotron radiation tomography provides 3D distribution map of local strain in polycrystalline aluminum alloy by tracking microstructural features. To perform further deep analysis on development of inhomogeneous deformation, crystallographic grain orientation is necessary. Three-dimensional X-ray diffraction technique was developed. A new crystallographic orientation measurement method was described in 3D space, utilizing grain boundary tracking （GBT） information.

Improvement of anticorrosion and adhesion to magnesium alloy by phosphate coating formed at room temperature

A new surface protection process was developed to magnesium alloy against corrosion in aggressive environments.Firstly,a phosphate coating was formed on rinsed magnesium alloy.Then,powder painting was carried out on the phosphated magnesium alloy.Surface morphologies and phase compositions of the phosphate coating were investigated by X-ray diffraction(XRD) and scanning electron microscope(SEM) .The results show that the phosphate coatings formed in bath containing earth additives at room temperature have dense and fine microstructure.The phosphate coating provides excellent paint adhesion to the magnesium alloy. Salt spray tests indicate that the corrosion resistance of the phosphate coating plus paint could meet the demand of magnesium alloy automobile components in aggressive environments.

A free-cutting and ductile CuAlMnZnTiB shape memory alloy

The mechanical properties and cutting performance of the designed Cu Al Mn Zn Ti B shape memory alloy were studied by tensile test and microstructure observation. Using X-ray diffractometry, differential scanning calorimetry(DSC) and semi-quantitative shape memory effect test, the microstructure and shape memory effect were analyzed. It is found that lots of βphase and few α phase are formed in the quenching of Cu-7.5Al-9.7Mn-3.4Zn-0.3Ti-0.14B(mass fraction, %) alloy, a great deal of martensite and few α phase are formed in the aging alloy, while the annealing alloy is composed of a great deal of α phase and few βphase. The tensile strength and elongation of the annealed alloy are 649 MPa and 17.1%, respectively. Some tiny and dispersion distributed second phase particles are generated in Ti and B precipitates, greatly improving the alloy machinability.

Effects of Y on mechanical properties and damping capacity of ZK60 magnesium alloys

The microstructure,mechanical properties and damping capacity of ZK60-xY(x=0,1.5%,2.5%,4.0%,mass fraction) magnesium alloys were investigated by using the optical microscope(OM),X-ray diffractometer(XRD),universal tensile testing machine and dynamic mechanical analyzer(DMA).The mechanisms for damping capacity of referred alloys were discussed by Granato-Lücke theory.The results show that Y additions remarkably reduce grain size(the average grain size is 21.6,13.0,8.6 and 4.0μm,respectively),and the tensile properties are enhanced with grain refining(the yield tensile strength increases to 292 MPa from 210 MPa and ultimate tensile strength increases to 330 MPa from 315 MPa).For the ZK60-xY(x=0,1.5%,4.0%)alloys,the damping capacity decreases with the increase of Y content.However,for the ZK60-xY(x=2.5%)alloy,the damping capacity improves abnormally,which is possibly related to the formation of Mg3Y2Zn3(W)FCC phase in this alloy.

Magnetostrictive distortion in Pr_(0.15)Tb_xDy_(0.85-x)Fe_2 polycrystals by X-ray diffraction

The ingots of Pr0.15TbxDy0.85-xFe2 （x=0.10-0.85） series compounds with a single phase were prepared -by a arc melting method. The X-ray diffraction patterns were measured using a Philips X’pert MPD X-ray diffractometer with a non-ambient sample stage at different temperatures, the magnetostrictive distortion in (Pr0.15TbxDy0.85-xFe2) polycrystals was investigated by X-ray diffraction patterns and the magnetostriction coefficient λ111 was calculated. The results show -when the temperature is raised above the spin reorientation temperature region, a splitting appears in the reflection （440）; the λ111 increase with the increasing of Tb content for (Pr0.15TbxDy0.85-xFe2) polycrystals and the full width at half maximum （FWHM） of the reflection （440） increases gradually with the increasing of Tb content. Moreover, as the FWHM of the reflection （440） decreases gradually with the increasing of temperature, the λ111 decreases slightly with the increasing of temperature at the temperature region of 223-373K for Pr0.15Tb0.3Dy0.55Fe2 alloy.

Finite element modeling and experiment for behavior estimation of AlMn0.5Mg0.5 sheet during electromagnetic forming

The electromagnetic forming is a procedure of high-speed processing,which favors the increase of the formability of some plastically deformed metals.In order to evaluate the capacity of some light metals,such as aluminum and its alloys,to be deformed through this procedure,it is useful to know the stress and strain state that occurs in the material during forming.In this work,the modeling of stresses and strains in electromagnetically deformed AlMn0.5Mg0.5 sheet was made.The modeling was achieved using the finite element method and it was verified through experimental tests.To determine the residual stresses,the X-ray diffraction method was used.The strains were established by measuring the displacements of the nodes in the network inscribed on the specimen by means of three coordinates measuring machine.A good agreement between the modeling results and experimental data was found.