Commercial purity and high purity titanium sheets were initially strained by a new technique, named as friction roll surface processing （FRSP）. Severe strain was imposed into the surface layer and strain gradient wa...Commercial purity and high purity titanium sheets were initially strained by a new technique, named as friction roll surface processing （FRSP）. Severe strain was imposed into the surface layer and strain gradient was formed through the thickness of the sheet. The microstructure and texture in as-strained state were investigated by optical microscopy and X-ray diffraction technique On the surface of the sheets, ultra-fine grains were found to have a sharp texture with a preferred orientation strongly related to the FRSP direction. The evolution of microstructure and crystallographic texture of FRSPed samples during recrystallization were also studied by electron back-scattered diffraction （EBSD） technique after being annealed at selected temperatures and time. The results indicated that the preferred orientations resulting from FRSP and annealing in the surface layer were formed during rolling and its recrystallization textures were reduced by FRSP. In addition, the texture evolved stably without change in main components during the annealing.展开更多
It has been known that the lack of excellent corrosion resistance is the key problem restricting the wide application of Mg−Li alloys.Based on a quantity of literature about corrosion behavior of Mg−Li alloys,this rev...It has been known that the lack of excellent corrosion resistance is the key problem restricting the wide application of Mg−Li alloys.Based on a quantity of literature about corrosion behavior of Mg−Li alloys,this review elaborates the factors affecting the corrosion behavior of Mg−Li alloys and the processing methods for improving corrosion resistance.The corrosion characteristics of Mg−Li alloys are described firstly.Then,it is explained that the grain size,orientation,second phase,and surface film strongly influence corrosion performance,which can be tailored by alloying,plastic deformation,and heat treatment.Further in-depth discussion about the corrosion mechanisms for Mg−Li alloys was also presented.Finally,important points of improving corrosion resistance are suggested.展开更多
Size distribution of nano-carbides produced by duplex treatments of surface nanocrystallization(by surface severe plastic deformation) and plasma electrolytic carburizing on CP-Ti was investigated.Skewness and kurtosi...Size distribution of nano-carbides produced by duplex treatments of surface nanocrystallization(by surface severe plastic deformation) and plasma electrolytic carburizing on CP-Ti was investigated.Skewness and kurtosis of Gussian shape distribution curves were studied and the effect of time was determined.The usage of longer time is more suitable for achieving less size of complex nano-carbides.Surface roughness of treated samples was measured.It is observed that there is an optimum level for time on surface roughness increasing(difference between two measured data).展开更多
基金support in part by Grant-in-aid for Scientific Research from the Japan Society for Promotion of Science under Contract No. 16560605
文摘Commercial purity and high purity titanium sheets were initially strained by a new technique, named as friction roll surface processing （FRSP）. Severe strain was imposed into the surface layer and strain gradient was formed through the thickness of the sheet. The microstructure and texture in as-strained state were investigated by optical microscopy and X-ray diffraction technique On the surface of the sheets, ultra-fine grains were found to have a sharp texture with a preferred orientation strongly related to the FRSP direction. The evolution of microstructure and crystallographic texture of FRSPed samples during recrystallization were also studied by electron back-scattered diffraction （EBSD） technique after being annealed at selected temperatures and time. The results indicated that the preferred orientations resulting from FRSP and annealing in the surface layer were formed during rolling and its recrystallization textures were reduced by FRSP. In addition, the texture evolved stably without change in main components during the annealing.
基金financial supports from the Natural Science Foundation of China (Nos. 51771060, 51871068, 51971071, 52011530025)the Domain Foundation of Equipment Advance Research of the 13th Fiveyear Plan, China (No. 61409220118)+2 种基金the National Key Research and Development Program, China (No. 2021YFE0103200)the Zhejiang Province Key Research and Development Program, China (No. 2021C01086)the Open Foundation of Key Laboratory of Superlight Materials & Surface Technology of Ministry of Education, China (No. HEU10202104)。
文摘It has been known that the lack of excellent corrosion resistance is the key problem restricting the wide application of Mg−Li alloys.Based on a quantity of literature about corrosion behavior of Mg−Li alloys,this review elaborates the factors affecting the corrosion behavior of Mg−Li alloys and the processing methods for improving corrosion resistance.The corrosion characteristics of Mg−Li alloys are described firstly.Then,it is explained that the grain size,orientation,second phase,and surface film strongly influence corrosion performance,which can be tailored by alloying,plastic deformation,and heat treatment.Further in-depth discussion about the corrosion mechanisms for Mg−Li alloys was also presented.Finally,important points of improving corrosion resistance are suggested.
基金Partial work of this project funded by National Elite Foundation of Iran and Iranian Nanotechnology Initiative is appreciated.
文摘Size distribution of nano-carbides produced by duplex treatments of surface nanocrystallization(by surface severe plastic deformation) and plasma electrolytic carburizing on CP-Ti was investigated.Skewness and kurtosis of Gussian shape distribution curves were studied and the effect of time was determined.The usage of longer time is more suitable for achieving less size of complex nano-carbides.Surface roughness of treated samples was measured.It is observed that there is an optimum level for time on surface roughness increasing(difference between two measured data).
