激光诱导环氧树脂表面液相化学局域增强沉积镍的实验研究

利用 10 79.5nmNd:YAP激光作诱导光源 ,环氧树脂作为基体 ,研究了激光功率、辐照时间对激光诱导化学局域镀覆金属镍的形成过程、微观形貌、厚度分布影响规律 。

阳极氧化对半固态成形ZL114A合金铸件耐蚀性能的影响

研究了阳极氧化工艺和表面液相偏析层对半固态成形ZL114A合金铸件耐蚀性的影响。结果表明:对于阳极氧化而言,表面液相偏析层会显著影响氧化膜生长速率,使得氧化膜厚度减小,但由于膜层平整,反而有利于氧化膜对合金耐蚀性能提高;然而,去除表面液相偏析层虽然会增加试样表面氧化膜的厚度,但由于这种氧化膜分布不均匀,从而无法提高合金的耐蚀性。未经阳极氧化处理的试样耐蚀性分析结果表明,表面液相偏析层的存在会降低试样的耐蚀性,去除表面液相偏析层会在一定程度上提高耐蚀性。对氧化膜腐蚀后的蚀坑研究发现,共晶组织对氧化膜的蚀坑的形成起着决定性作用,蚀坑通常位于共晶组织部位,且在蚀坑中往往发现有富铁金属间化合物。

HDPE-g-MAH改性氢氧化铝阻燃PP

在液相中用马来酸酐接枝高密度聚乙烯(HDPE-g-MAH)表面改性Al(OH)_3以改善其在高分子基相中的分散性。形态观察表明,用适量HDPE-g-MAH处理Al(OH)_3可改善Al(OH)_3在聚丙烯(PP)中的分散性,从而提高体系的力学性能;HDPE-g-MAH用量过多造成的Al(OH)_3粒子间桥联,该现象经熔融混合后依然存在,导致力学性能降低。偏光显微镜观察显示,适量HDPE-g-MAH处理Al(OH)_3可改善PP的结晶形态。

撞击流微反应器气液传质研究

在T型对撞反应器的基础上,对其结构进行改进,设计了旋流锥型对撞、T型旋撞和旋流锥型旋撞(二次旋转)3种撞击流反应器。用化学吸收法测量了这几种不同结构的微反应器在气液二相逆流接触条件下平均相界比表面积α及液相吸收传质系数kL;进而分析了反应器进口结构、尺寸和流体流量等条件对传质性能的影响。结果表明:旋撞比直撞的传质系数大,二次旋撞的比一次旋撞的传质系数要大;撞击区进口尺寸越小,气液流体的流量越大,反应器的传质系数越大;液相传质系数较常规气液接触设备的至少高1—2个数量级,其传质强化的原因主要源于微反应器内相界比表面积大幅度地增加。

Haemocompatibility of Ti-3Zr-2Sn-3Mo-25Nb biomedical alloy with surface heparinization using electrostatic self assembly technology

The haemocompatibility of Ti-3Zr-2Sn-3Mo-25Nb biomedical alloy was studied after surface heparinization. A layer of sol-gel TiO2 films was applied on the alloy samples followed by active treatment in the bio-functionalized solution for introducing the OH- and groups, and then the heparin was immobilized on the active TiO2 films through the electrostatic self assembly technology. It is shown that the heparinized films are mainly composed of anatase and rutile with smooth and dense surface. In vitro blood compatibility was evaluated by haemolysis test, clotting time and platelet adhesion behavior tests. The results show that the haemocompatibility of the alloy could be significantly improved by surface heparinization.

4-氯-2,2-二氰基-N-氯乙酰基丁酰胺-3-酮的合成

以甲氨酰二氰基甲基化钾为原料，在室温条件下，采用固液相表面接触法与过量氯乙酰氯反应，合成了具有多个功能基的丁酰胺类化合物4-氯-2，2-二氰基-N-氯乙酰基丁酰胺-3-酮，产率为11．2％；m．P．147．8～148、1℃；其结构经IR、^1H NMR确认．

Contact Angle Hysteresis and Hysteresis Tension on Rough Solid Surface

Observation and measurement were conducted to investigate contact angle andits hysteresis on rough surface. The experimental results indicate that the increase in solidsurface roughness enlarges advancing contact angle and decreases receding contact angle, resultingin enhanced hysteresis. It was observed that when Young''s contact angle θ_Y 【 90°, as theroughness of solid surface increased the extent of the decrease in receding contact angle exceededthat of the increase in advancing contact angle. Based on the experimental observations, the conceptof hysteresis tension was introduced to describe the contact angle hysteresis behavior on roughsolid surface. The model provides a thoughtful understanding of the physical nature of contact anglehysteresis, in particular an instructive description of the influence of surface roughness on thehysteresis. The prediction of the model is found in quite good agreement with the experimentalobservation and measurement.

Liquid Film Characteristics on Surface of Structured Packing

Structured packing is a good candidate for CO2 capture process because of its higher mass transfer efficiency and lower pressure drop. Now, the challenging problem of CO2 capture and storage demands more and more efficiency equipment. The aim of the present study is to investigate the liquid film characteristics under counter current gas phase and throw some insight into the enhancing mechanism of mass transfer performance in structured packing. A high speed digital camera, non-intrusive measurement technique, was used. Water and air were working fluids. Experiments were carried out for different gas/liquid flow rates and different inclination angles. The time-average and instantaneous film widths for each set of flow parameters were calculated. It is shown that the effects of gas phase could be neglected for lower flow rate, and then, become more pronounced at higher flow rate. According to instantaneous film width, three different stages can be distinguished. One is the constant width of liquid film. The second is the slight decrease of film width and the smooth surface. This kind of character will lead to less interfacial area and deteriorate the packing mass transfer performance. For the third stage, the variation of film width shows clearly chaotic behavior. The prediction model was also developed in present work. The predicted and experimental results are in good agreement.

Directional migration behavior of cerium during sintering process of mischmetal doped cemented carbide

Three observation methods were used to investigate the existing form and the behavior of rare earth during the sintering process of high activity mischmetal （RE, with lanthanum and cerium） doped WC-8%Co-0.048%RE（mass fraction） alloy with low carbon-containing level by scanning electron microscopy （SEM） and energy dispersive X-ray spectroscopy （EDXS）, considering the fact that the addition amount of rare earth in the alloy is very minute. The directional migration process and mechanism of cerium were discussed. First, the sinter skin （surface） is observed. oxide on the sinter skin, and lanthanum in these cerium observed, and lanthanum containing phase/micro-zone in It is shown that there exists a dispersedly distributed cerium containing enrichment positions is very minute. Secondly, the polished section is the alloy is identified. Finally, based on the fact that the fracture of cemented carbide is resulted from the heterogeneous phase or other defects within the microstructure, the fracture surface is observed and cerium containing phase/micro-zone in the fracture source approximately 260 μm from the surface is identified. These combined observations reveal adequately the fact that lanthanum and cerium get separated and cerium predominantly migrates towards the surface during the sintering process.

Cloud-point extraction and preconcentration of bisphenol A from water samples

A novel cloud-point extraction （CPE） was successfully used in preconcentration of biphenol A （BPA） from aqueous solutions. Majority of BPA is extracted into the surfactant-rich phase. The parameters affecting the CPE such as concentration of surfactant and electrolyte, equilibration temperature and time and pH of sample solution were investigated. The samples were analyzed by high-performance liquid chromatography with ultraviolet detection. Under the optimized conditions, preconcentration of 10 mL sample gives a preconcentration factor of 11. The limit of detection （LOD） and limit of quantification （LOQ） are 0.1 μg/L and 0.33 μg/L, respectively. The linear range of the proposed method is 0.2-20 μg/L with correlation coefficients greater than 0.998 7 and the spiking recove6es are 97.96%-100.42%. The interference factor was tested and the extraction mechanism was also investigated. Thus, the developed CPE has proven to be an efficient, green, rapid and inexpensive approach for extraction and preconcentration of BPA from water samples.

Influence of Nitric Acid Concentration on Characteristics of Olive Stone Based Activated Carbon

In this work we investigated the effect of nitric acid concentration on the pore structure,surface chemistry and liquid phase adsorption of olive stone based activated carbon prepared by mixing process using phosphoric acid and steam as activating agents.Chemicals and textural characterization show that the increase of HNO3concentration increases considerably the total acidic groups but decreases specific surface area and pore volume.The study of adsorption in aqueous solutions of two organics,phenol and methylene blue,on raw and oxidized activated carbon indicates that the treatment of mixed activated carbon with different concentrations of nitric acid improves the adsorbent capacity for methylene blue at HNO3concentrations less or equal to 2 mol·L 1,while it has a negative effect on phenol adsorption.

Influence of Surface Geometry of Grating Substrate on Director in Nematic Liquid Crystal Cell

The director in nematic liquid crystal cell with a weak anchoring grating substrate and a strong anchoring planar substrate is relative to the coordinates x and z.The influence of the surface geometry of the grating substrate in the cell on the director profile is numerically simulated using the two-dimensional finite-difference iterative method under the condition of one elastic constant approximation and zero driven voltage.The deepness of groove and the cell gap affect the distribution of director.For the relatively shallow groove and the relatively thick cell gap,the director is only dependent on the coordinate z.For the relatively deep groove and the relatively thin cell gap,the director must be dependent on the two coordinates x and z because of the increased elastic strain energy induced by the grating surface.

Reconstructing bubble profiles from gas-liquid two-phase flow data using agglomerative hierarchical clustering method

The knowledge of bubble profiles in gas-liquid two-phase flows is crucial for analyzing the kinetic processes such as heat and mass transfer, and this knowledge is contained in field data obtained by surface-resolved computational fluid dynamics (CFD) simulations. To obtain this information, an efficient bubble profile reconstruction method based on an improved agglomerative hierarchical clustering (AHC) algorithm is proposed in this paper. The reconstruction method is featured by the implementations of a binary space division preprocessing, which aims to reduce the computational complexity, an adaptive linkage criterion, which guarantees the applicability of the AHC algorithm when dealing with datasets involving either non-uniform or distorted grids, and a stepwise execution strategy, which enables the separation of attached bubbles. To illustrate and verify this method, it was applied to dealing with 3 datasets, 2 of them with pre-specified spherical bubbles and the other obtained by a surface-resolved CFD simulation. Application results indicate that the proposed method is effective even when the data include some non-uniform and distortion.

Rebound behaviors of droplets impacting on a superhydrophobic surface

The rebound behaviors of droplets impacting on a self-fabricated superhydrophobic brass surface （WCA=I64.5°） were ob- served and studied by using high-speed-camera. In accordance with energy conversion, theoretical analysis of different behav- iors and rebound mechanism were given. At lower velocities, three behaviors in different velocity ranges were observed： par- tial rebounding, entire rebounding and ejecting during rebounding. At higher velocities, such two behaviors as rebound after splashing and rebound, ejecting after splashing, occurred alternately and exhibited certain periodicity. A function to predict the critical impact velocity is derived from energy conservation condition, and the prediction values tally with the experimental values, with the maximum relative error about 14%.

Flame Spread over Aviation Kerosene with an Obstacle in Liquid Phase

The phenomena of flame spread over aviation kerosene with an obstacle in liquid phase are investigated experimentally through surface temperature measurement by using infrared camera,schlieren images of subsurface flow in front of and behind obstacle and residence time of flame obtained from video recording.Experimental results reveal that obstacle has no effect on gas phase controlled flame spread.But for liquid phase controlled flame spread,flame can be stopped by an obstacle with its top edge flush with oil surface,and the residence time decreases with the increase of initial temperature of fuel.That conduction and radiation only play a subsidiary role in flame spread over liquid fuel was proved by schlieren images and surface temperature profiles.