To analyze the influence of surface texture on friction properties of Crl2MoV＇, ordinary grinder and spinning technology were adopted to obtain the grooved surface morphology of samples, and then the impact of spindl...To analyze the influence of surface texture on friction properties of Crl2MoV＇, ordinary grinder and spinning technology were adopted to obtain the grooved surface morphology of samples, and then the impact of spindle speed and feed in z-direction on surface morphology in the process of spinning was studied. In addition, the corresponding friction coefficient of sample was obtained through friction and wear tests. The results show that the peak clipping and the valley filling were conducted on the grinding surface, which could improve the surface roughness effectively and make the grinding trench-type wear scar more uniform. Both the area ratio of groove and groove spacing increased initially and then decreased with the increase of the spindle speed or the feed in z-direction. As a kind of micro-process, the groove could influence the friction coefficient of sample surface, whose distribution was beneficial to the reduction of friction coefficient. Compared with the surface obtained through ordinary grinding, grooved surface morphology through spinning technology was more conductive to reduce the friction coefficient, which could be reduced by 25%. When the friction coefficient of sample was reduced to the minimum, the texture of groove corresponded had an optimal area ratio and an optimal groove spacing, 37.5% and 27.5 μm, respectively.展开更多
Laser alloying was used for production of thick layers on surface of Nimonic 80A-alloy.For laser surface modification,three types of pre-coated pastes were applied:with amorphous boron,with amorphous boron and molybde...Laser alloying was used for production of thick layers on surface of Nimonic 80A-alloy.For laser surface modification,three types of pre-coated pastes were applied:with amorphous boron,with amorphous boron and molybdenum as well as with amorphous boron and niobium.The microstructure,hardness and wear resistance of produced layers were studied in details.The presence of different types of borides in re-melted zone depended on the paste composition and caused an increase in hardness up to about HV 1000.The wear resistance was evaluated by calculation of mass wear intensity factor Imw and relative mass loss of specimen and counter-specimen.The wear behavior of the tested frictional pairs was determined by 3D interference microscopy,scanning electron microscopy equipped with EDS microanalyzer.The significant increase in abrasive wear resistance was observed in comparison to untreated Nimonic 80A-alloy.The lowest mass loss intensity factor was characteristic of laser-alloyed Nimonic 80A-alloy with boron and niobium(Imw=1.234 mg/(cm2?h)).Laser alloyed-layers indicated abrasive wear mechanism with clearly visible grooves.Laser alloying with boron and niobium resulted in the additional oxidative wear mechanism.In this case,EDS patterns revealed presence of oxygen on the worn surface of specimen.展开更多
基金Project(51275543)supported by the National Natural Science Foundation,ChinaProject(KJ1603804)supported by the Research Projects of Chongqing Commission of Science and Technology,China
文摘To analyze the influence of surface texture on friction properties of Crl2MoV＇, ordinary grinder and spinning technology were adopted to obtain the grooved surface morphology of samples, and then the impact of spindle speed and feed in z-direction on surface morphology in the process of spinning was studied. In addition, the corresponding friction coefficient of sample was obtained through friction and wear tests. The results show that the peak clipping and the valley filling were conducted on the grinding surface, which could improve the surface roughness effectively and make the grinding trench-type wear scar more uniform. Both the area ratio of groove and groove spacing increased initially and then decreased with the increase of the spindle speed or the feed in z-direction. As a kind of micro-process, the groove could influence the friction coefficient of sample surface, whose distribution was beneficial to the reduction of friction coefficient. Compared with the surface obtained through ordinary grinding, grooved surface morphology through spinning technology was more conductive to reduce the friction coefficient, which could be reduced by 25%. When the friction coefficient of sample was reduced to the minimum, the texture of groove corresponded had an optimal area ratio and an optimal groove spacing, 37.5% and 27.5 μm, respectively.
基金financially supported within the project "Engineer of the Future.Improving the didactic potential of the Poznan University of Technology"-POKL.04.03.00-00-259/12,implemented within the Human Capital Operational Programme,co-financed by the European Union within the European Social Fundby Ministry of Science and Higher Education in Poland as a part of the 02/24/DSPB project
文摘Laser alloying was used for production of thick layers on surface of Nimonic 80A-alloy.For laser surface modification,three types of pre-coated pastes were applied:with amorphous boron,with amorphous boron and molybdenum as well as with amorphous boron and niobium.The microstructure,hardness and wear resistance of produced layers were studied in details.The presence of different types of borides in re-melted zone depended on the paste composition and caused an increase in hardness up to about HV 1000.The wear resistance was evaluated by calculation of mass wear intensity factor Imw and relative mass loss of specimen and counter-specimen.The wear behavior of the tested frictional pairs was determined by 3D interference microscopy,scanning electron microscopy equipped with EDS microanalyzer.The significant increase in abrasive wear resistance was observed in comparison to untreated Nimonic 80A-alloy.The lowest mass loss intensity factor was characteristic of laser-alloyed Nimonic 80A-alloy with boron and niobium(Imw=1.234 mg/(cm2?h)).Laser alloyed-layers indicated abrasive wear mechanism with clearly visible grooves.Laser alloying with boron and niobium resulted in the additional oxidative wear mechanism.In this case,EDS patterns revealed presence of oxygen on the worn surface of specimen.
