Thermal and moisture characteristics of the bamboo structure wall were tested in natural climate and three representative variation processes of heat and moisture： heating from solar radiation in summer at normal tem...Thermal and moisture characteristics of the bamboo structure wall were tested in natural climate and three representative variation processes of heat and moisture： heating from solar radiation in summer at normal temperature and humidity, heating from solar radiation in summer at normal temperature and high humidity after rain, humidifying from brash in summer at high temperature and normal humidity. The results show that, in summer, the largest temperature difference between external and internal surface of the 28 mm-thick bamboo plywood wall is 11.73℃ （at 15：40） and the largest strain difference is 136 μm/m （at 18：50）, both in ambient and indoor conditioned environment. In heating process, lengthways of the wall surface are in contracting strain while transverse ways are in expanding strain at initial stage and in contracting strain during later period. When the high temperature wall is humidified by rain, the surface temperature drops, moisture content increases and the expanding strain is presented on the surface during the whole process. Temperature and moisture content are two important factors which affect thermal and moisture stress （TMS） of the bamboo structure wall. The TMS is not only related to temperature and moisture content, but also greatly affected by temperature gradient, moisture content gradient and rates of changing.展开更多
Static and dynamic wetting behaviors of sessile droplet on smooth,microstructured and micro/nanostructured surface under condensation condition are systematically studied.In contrast to the conventional droplet wettin...Static and dynamic wetting behaviors of sessile droplet on smooth,microstructured and micro/nanostructured surface under condensation condition are systematically studied.In contrast to the conventional droplet wetting on such natural materials by dropping,we demonstrate here that when dropwise condensation occurs,the sessile droplet will transit from the Cassie-Baxter wetting state to the Wenzel wetting state or partial Cassie-Baxter wetting state on the microstructured surface or the micro/nanostructured surface,which leads to a strong adhesion between the droplet and the substrate.In contrast,the apparent contact angle and the sliding angle on the smooth surface changes a little before and after the condensation because of small roughness.Theoretical analysis shows that the roughness factor controls the adhesion force of the droplet during condensation,and a theoretical model is constructed which will be helpful for us to understand the relationship between the adhesion force and the geometry of the surface.展开更多
基金Project(50878078) supported by the National Natural Science Foundation of China
文摘Thermal and moisture characteristics of the bamboo structure wall were tested in natural climate and three representative variation processes of heat and moisture： heating from solar radiation in summer at normal temperature and humidity, heating from solar radiation in summer at normal temperature and high humidity after rain, humidifying from brash in summer at high temperature and normal humidity. The results show that, in summer, the largest temperature difference between external and internal surface of the 28 mm-thick bamboo plywood wall is 11.73℃ （at 15：40） and the largest strain difference is 136 μm/m （at 18：50）, both in ambient and indoor conditioned environment. In heating process, lengthways of the wall surface are in contracting strain while transverse ways are in expanding strain at initial stage and in contracting strain during later period. When the high temperature wall is humidified by rain, the surface temperature drops, moisture content increases and the expanding strain is presented on the surface during the whole process. Temperature and moisture content are two important factors which affect thermal and moisture stress （TMS） of the bamboo structure wall. The TMS is not only related to temperature and moisture content, but also greatly affected by temperature gradient, moisture content gradient and rates of changing.
基金supported by the National Natural Science Foundation of China(Grant Nos.11072126,11272176,91326108 and 51206042)the Foundation of Stake Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources(Grant No.LAPS14018)
文摘Static and dynamic wetting behaviors of sessile droplet on smooth,microstructured and micro/nanostructured surface under condensation condition are systematically studied.In contrast to the conventional droplet wetting on such natural materials by dropping,we demonstrate here that when dropwise condensation occurs,the sessile droplet will transit from the Cassie-Baxter wetting state to the Wenzel wetting state or partial Cassie-Baxter wetting state on the microstructured surface or the micro/nanostructured surface,which leads to a strong adhesion between the droplet and the substrate.In contrast,the apparent contact angle and the sliding angle on the smooth surface changes a little before and after the condensation because of small roughness.Theoretical analysis shows that the roughness factor controls the adhesion force of the droplet during condensation,and a theoretical model is constructed which will be helpful for us to understand the relationship between the adhesion force and the geometry of the surface.
