复合材料筋混凝土梁裂缝开展试验分析及宽度计算

分析了光圆GFRP筋混凝土梁和螺纹状表面粘砂CFRP筋、GFRP筋混凝土梁的开裂机理、裂缝开展过程、开裂形态、配筋率等因素对裂缝宽度和裂缝间距的影响,同时对ACI440.1R-01推荐的裂缝宽度计算公式与其他公式进行了对比和验证。结果表明:ACI440.1R-01公式预测值与试验值吻合较好,并推荐了该公式有关参数的取值。

Failure of rock under dynamic compressive loading

Split Hopkinson Pressure Bar(SHPB) test was simulated to investigate the distribution of the first principal stress and damage zone of specimen subjected to dynamic compressive load. Numerical models of plate-type specimen containing cracks with inclined angles of 0°,45° and 90° were also established to investigate the crack propagation and damage evolution under dynamic loading. The results show that the simulation results are in accordance with the failure patterns of specimens in experimental test. The interactions between stress wave and crack with different inclined angles are different; damage usually appears around the crack tips firstly; and then more damage zones develop away from the foregoing damage zone after a period of energy accumulation; eventually,the damage zones run through the specimen in the direction of applied loading and split the specimen into pieces.

Effects of discontinuities on penetration of TBM cutters

Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the effects of discontinuities on cutting characteristics and cutting efficiency. In laboratory tests, five propagation patterns of radial cracks are observed. And in the numerical tests, firstly, it is similar to laboratory tests that cracks ahead of cutters mainly initiate from the crushed zone, and some minor cracks will initiate from joints. The cracks initiating from crushed zones will run through the thinner joints while they will be held back by thick joints. Cracks tend to propagate towards the tips of embedded cracks, and minor cracks will initiate from the tips of embedded cracks, which may result in the decrease of specific area, and disturbing layers play as ‘screens', which will prevent cracks from developing greatly. The peak penetration forces, the consumed energy in the penetration process and the uniaxial compression strength will decrease with the increase of discontinuities. The existence of discontinuities will result in the decrease of the cutting efficiency when the spacing between cutters is 70 mm. Some modifications should be made to improve the efficiency when the rocks containing groups of discontinuities are encountered.

Fractal characteristics of cracks and fragments generated in unloading rockburst tests

True triaxial rockburst experiments with four different unloading rates were performed on four prism specimens of granite sampled from Beishan, China. The damage evolution in the rockburst test was investigated from two aspects including fracture surface crack and fragment characteristics. The scanning electron microscopy was used to observe the micro crack information on fragment surface. Combing binarization and box counting dimensions, the fractal dimensions of cracks were obtained. Meanwhile,the fragments were collected and a sieving experiment was conducted. We weighed the fragments qualities, counted the amount of fragments and measured the fragments length, width and thickness.Utilizing four methods to calculate damage fractal dimensions of fragments, the trend of fractal value changing with unloading rates can be roughly described. It can be concluded from these experiments that the fractal dimension either for crack or for fragment holds a decreasing trend with the decreasing unloading rate, indicating a reduction of damage level.

Analysis of pre-crack kinking and delamination in terms of SLB test of honeycomb sandwich structure

The flatwise tension(FWT) and single leg bending(SLB) tests were used to investigate the fracture behavior of honeycomb sandwich specimens.In the FWT test,only the interlaminar delamination was observed.The test results show that the interfacial peel strength is higher than the interlaminar peel strength.In terms of SLB experiment,a new fracture mode was found,namely IKP(initiation of interlaminar delamination,kinking into facesheet and propagation of interlaminar delamination).The virtual crack closure technique was applied to separate the values of Mode I and Mode II components of the strain energy release rate in SLB experiment.The finite element analysis result shows that the Mode I strain energy release rate is higher than the Mode II strain energy release rate.To simulate the failure of SLB test of honeycomb sandwich specimens,a new computational model based on the Tsai-Hill failure criterion and the cohesive zone model is proposed.In comparison with experimental results,it can be concluded that the computational model can validly simulate the IKP of a honeycomb sandwich structures with reasonable accuracy.

Model Experiment on Integral Seismic Behavior of Reinforced Concrete Frame with Split Columns

Based on a series of previous studies, an experiment on the integral seismic behavior of a 1/3 scaled model of two-bay and three-story reinforced concrete frame with split columns at lower two stories is performed under cyclic loading. The original columns at lower two stories of the model frame are short columns and they are replaced by the split columns. The hysteresis curves between the horizontal cyclic load and the lateral displacement at the top of the model frame, indicate that under the cyclic loading, the model frame undergoes the process of cracking, yielding, and maximum loading before being destroyed at the ultimate load. They also indicate that the model frame has better ductility, and the ratio of the ultimate displacement to the yielding displacement, reaches 6.0. The yielding process of the model frame shows that for the frame with split columns, plastic hinges are generated at the ends of beams and then the columns begin yielding while the frame still possesses the bearing and deformation capacity. The design idea of directly changing the short column to long one in the reinforced concrete frame may be realized by replacing the short column with the split one.

Experimental study of seepage characteristics of single rock fracture based on stress states and stress history

Through seepage tests under different loading and unloading confining pressures and different hydraulic gradients,the authors studied the effects of stress states and stress history on fracture permeability evolution for single granite fracture and sandstone fracture. The results show that there exists a linear relationship between the seepage discharge and osmotic pressure in sandstone fissure under each level of confining pressure. With the increasing in the confining pressure,the permeability of the fracture decreases,but the decreasing rate is changeing. During the unloading process,the fracture seepage velocity cannot be fully recovered to the size of the loading process. Therefore,in the unloading process of the confining pressure,the recovery of fracture permeability shows obvious hysteresis effects. The flow rate of the fracture remains unchanged during five cycles of loading and unloading processes of the confining pressure. In each cycle,the evolution character of the flow rate with the confining pressure remains unchanged. These experiments show that the seepage characteristics of sandstone and granite fractures are not the same under the same stress state.

Fracture analysis of cracked metallic plate repaired with adhesive bonding composite patch

Fatigue crack growth test of cracked metallic plate repaired with adhesive bonding composite patch was conducted to study the fracture behavior of crack patching. The failure mode was that crack grows along with adhesive debonding. The crack length and debonding area were measured at different numbers of cycles. The nonlinear three- dimensional(3D)finite element(FE)model considering adhesive debonding and crack growth simultaneously was developed. The experimental and analytical results were in good agreement with each other.

Test evaluation for vertical fracture wells in low permeability reservoir

As flow environment is poor in low permeability reservoirs, wells are always fractured in order to gain better economic benefits. Well testing analysis is very necessary for fracturing wells. However, available test analysis methods are of slow fitting speed and low fitting precision. In this paper, we first use a comprehensive evaluation method of analytical well testing, numerical well testing and well testing design. Many dynamic parameters such as fracture length, fracture conductivity, skin factor, etc are obtained. An example to illustrate accurate results of this method is given.

A Comparative Study on the Flexural Behaviour of Waffle and Solid Slab Models When Subjected to Point Load

The determinations of flexural behavior of some engineering structures are based on different theories and equations, but it has been observed that some of these equations may not give true representation. This work has looked into the difference that may occur between theoretical and experimental results. An experimental test carried out on models of waffle and solid slabs structures were described and results from twenty test samples are presented. Each specimen was subjected to an incremental axial loading of 1 kN interval after 28 days of casting. The flexural moments, deflections and crack width at failure were obtained. The experimental flexural crack and theoretical flexural cracks for both types of slabs were compared. The result for flexural moments for waffle was 5.526 kNm, while solid slab was 3.684 kNm. The deflections showed that waffle slabs has 3.64 mm while solid has 9.28 mm, hence waffle has a higher structural stiffness than solid slabs, but the flexural cracks did not give the same results especially for the estimated crack width. It was concluded that estimated results based on developed equations may not be accurate because it is based on ideal situation.

Formation of wavy-ring crack in drying droplet of protein solutions

The formations of desiccation cracks and their pattems in drying droplets of protein solutions are studied experimentally. The solvent evaporation causes the dehydration self-organization phenomenon in colloidal droplets, followed by the formations of desiccation cracks. Two categories of highly ordered crack patterns, which we name ＂daisy＂ and ＂wavy-ring＂, are identified in the drying droplets. We explore the shifting of crack patterns from the ＂daisy＂ to the ＂wavy-ring＂ by varying the concentration of protein droplets. The results show that the concentration correlates with the pattern of deposition film directly, and modulates the periodicity of the crack pattern. We investigate the formations and periodicities of these two kinds of crack patterns, and obtain the scaling law of periodicity of the ＂wavy-ring＂ crack pattern. The relationship between the deposition pattern and the highly ordered crack patterns is also examined. This study will help in understanding the formation mechanisms of crack patterns in drying droplets of protein solutions and assist the future design of crack patterns in practical applications.