本文观察结果,光镜显示皮肤触盘表皮增厚,其基底部有成群的麦克尔细胞(MC)。电镜下除观察到 MC 的分叶核,核内棒状小体、胞质含致密核心膜包颗粒、中间丝和中心粒及与 MC 接触的另一类含致密核心膜包小泡的神经终末外,首次报道粗面内质...本文观察结果,光镜显示皮肤触盘表皮增厚,其基底部有成群的麦克尔细胞(MC)。电镜下除观察到 MC 的分叶核,核内棒状小体、胞质含致密核心膜包颗粒、中间丝和中心粒及与 MC 接触的另一类含致密核心膜包小泡的神经终末外,首次报道粗面内质同与高尔基体和特殊颗粒的形态学联系。对过渡细胞等问题作了探讨。展开更多
The construction efficiency and quality of tunnel boring machines(TBMs)is largely determined by the service life of cutting tools,which is the result of contact loads in the crushed zone between cutter ring and rock.I...The construction efficiency and quality of tunnel boring machines(TBMs)is largely determined by the service life of cutting tools,which is the result of contact loads in the crushed zone between cutter ring and rock.In this paper,a series of rock breaking tests were conducted with a 216 mm diameter disc cutter and concrete samples.Based on the superposition principle,the distribution of contact loads between disc cutter and rock were obtained by using the truncated singular value decomposition(TSVD).The results show that both the peak value and the whole numerical distribution of the radial strains on the cutter ring increase with the increase of the penetration.The distribution curves of the contact loads show an approximate parabola going downwards,which indicates contact loads are more concentrated.The front non-loading area with a ratio from 1.8%to 5.4%shows an increasing trend with the increase of penetration.However,the change of rear non-loading area is not obvious.It is believed that the conclusions have guidance for the study of rock breaking mechanism and manufacturing process of the disc cutter.展开更多
Mass transfer characteristics have been investigated in a 113 mm diameter asymmetric rotating disk contactor of the pilot plant scale for two different liquid–liquid systems. The effects of operating parameters inclu...Mass transfer characteristics have been investigated in a 113 mm diameter asymmetric rotating disk contactor of the pilot plant scale for two different liquid–liquid systems. The effects of operating parameters including rotor speed and continuous and dispersed phase velocities on the volumetric overall mass transfer coefficients are investigated. The results show that the mass transfer performance is strongly dependent on agitation rate and interfacial tension, but only slightly dependent on phase flow rates. In this study, effective diffusivity is used instead of molecular diffusivity in the Grober equation for estimation of dispersed phase overall mass transfer coefficient.The enhancement factor is determined experimentally and there from an empirical expression is derived for prediction of the enhancement factor as a function of Reynolds number. The predicted results compared to the experimental data show that the proposed correlation can efficiently predict the overall mass transfer coefficients in asymmetric rotating disk contactors.展开更多
The development of pressure sensors with highly sensitivity, fast response and facile fabrication technique is desirable for wearable electronics. Here, we successfully fabricated a flexible transparent capacitive pre...The development of pressure sensors with highly sensitivity, fast response and facile fabrication technique is desirable for wearable electronics. Here, we successfully fabricated a flexible transparent capacitive pressure sensor based on patterned microstructured silver nanowires(AgNWs)/polydimethylsiloxane(PDMS) composite dielectrics. Compared with the pure PDMS dielectric layer with planar structures, the patterned microstructured sensor exhibits a higher sensitivity(0.831 kPa^-1, <0.5 kPa), a lower detection limit,good stability and durability. The enhanced sensing mechanism about the conductive filler content and the patterned microstructures has also been discussed. A 5×5 sensor array was then fabricated to be used as flexible and transparent wearable touch keyboards systems. The fabricated pressure sensor has great potential in the future electronic skin area.展开更多
基金Project(51475478)supported by the National Natural Science Foundation of ChinaProject(2013CB035401)supported by the National Basic Research Program of China
文摘The construction efficiency and quality of tunnel boring machines(TBMs)is largely determined by the service life of cutting tools,which is the result of contact loads in the crushed zone between cutter ring and rock.In this paper,a series of rock breaking tests were conducted with a 216 mm diameter disc cutter and concrete samples.Based on the superposition principle,the distribution of contact loads between disc cutter and rock were obtained by using the truncated singular value decomposition(TSVD).The results show that both the peak value and the whole numerical distribution of the radial strains on the cutter ring increase with the increase of the penetration.The distribution curves of the contact loads show an approximate parabola going downwards,which indicates contact loads are more concentrated.The front non-loading area with a ratio from 1.8%to 5.4%shows an increasing trend with the increase of penetration.However,the change of rear non-loading area is not obvious.It is believed that the conclusions have guidance for the study of rock breaking mechanism and manufacturing process of the disc cutter.
文摘Mass transfer characteristics have been investigated in a 113 mm diameter asymmetric rotating disk contactor of the pilot plant scale for two different liquid–liquid systems. The effects of operating parameters including rotor speed and continuous and dispersed phase velocities on the volumetric overall mass transfer coefficients are investigated. The results show that the mass transfer performance is strongly dependent on agitation rate and interfacial tension, but only slightly dependent on phase flow rates. In this study, effective diffusivity is used instead of molecular diffusivity in the Grober equation for estimation of dispersed phase overall mass transfer coefficient.The enhancement factor is determined experimentally and there from an empirical expression is derived for prediction of the enhancement factor as a function of Reynolds number. The predicted results compared to the experimental data show that the proposed correlation can efficiently predict the overall mass transfer coefficients in asymmetric rotating disk contactors.
基金supported by the National Natural Science Foundation for Distinguished Young Scholars of China(NSFC,61625404)the Key Research Program of Frontier Sciences,CAS(QYZDY-SSW-JWC004)the NSFC(61504136)
文摘The development of pressure sensors with highly sensitivity, fast response and facile fabrication technique is desirable for wearable electronics. Here, we successfully fabricated a flexible transparent capacitive pressure sensor based on patterned microstructured silver nanowires(AgNWs)/polydimethylsiloxane(PDMS) composite dielectrics. Compared with the pure PDMS dielectric layer with planar structures, the patterned microstructured sensor exhibits a higher sensitivity(0.831 kPa^-1, <0.5 kPa), a lower detection limit,good stability and durability. The enhanced sensing mechanism about the conductive filler content and the patterned microstructures has also been discussed. A 5×5 sensor array was then fabricated to be used as flexible and transparent wearable touch keyboards systems. The fabricated pressure sensor has great potential in the future electronic skin area.
