The electronic packaging box with high silicon aluminum-base alloy was prepared by semi-solid thixoforming technique.The flow characteristic of the Si phase was analyzed.The microstructures of different parts of the b...The electronic packaging box with high silicon aluminum-base alloy was prepared by semi-solid thixoforming technique.The flow characteristic of the Si phase was analyzed.The microstructures of different parts of the box were observed by optical microscopy and scanning electron microscopy,and the thermophysical and mechanical properties of the box were tested.The results show that there exists the segregation phenomenon between the primary Si phase and the liquid phase during thixoforming,the liquid phase flows from the box,and the primary Si phase accumulates at the bottom of the box.The volume fraction of primary Si phase decreases gradually from the bottom to the walls.Accordingly,the thermal conductivities of bottom center and walls are 107.6 and 131.5 W/（m·K）,the coefficients of thermal expansion（CTE） are 7.9×10-6 and 10.6×10-6 K-1,respectively.The flexural strength increases slightly from 167 to 180 MPa.The microstructures and properties of the box show gradient distribution overall.展开更多
Gives a dynamic mathematical model of a typical type of multiple discs hydroviscous drive device which has been proved to be correct through tests.Utilizing the method of root-locus analysis the dynamic performance of...Gives a dynamic mathematical model of a typical type of multiple discs hydroviscous drive device which has been proved to be correct through tests.Utilizing the method of root-locus analysis the dynamic performance of this device is studied according to the model.Theoretical analysis and test re- suits show that the dynamic performance of the object of study can be greatly improved by speed negative feedback.展开更多
In this feasibility study, we investigate the viability of using Liquefied Natural Gas （LNG） fuel in an open type Ro-Ro passenger ferry and the associated potential challenges with regard to the vessel safety system...In this feasibility study, we investigate the viability of using Liquefied Natural Gas （LNG） fuel in an open type Ro-Ro passenger ferry and the associated potential challenges with regard to the vessel safety systems. We recommend an appropriate methodology for converting existing ships to run on LNG fuel, discuss all the necessary modifications to the ship’s safety systems, and also evaluate the relevant ship evacuation procedures. We outline the basic requirements with which the ship already complies for each safety system and analyze the additional restrictions that must be taken into consideration for the use of LNG fuel. Appropriate actions are recommended. Furthermore, we carry out a hazard identification study. Overall, we clearly demonstrate the technical feasibility of the investigated scenario. Minimal modifications to the ship’s safety systems are required to comply with existing safety rules for this specific type of ship.展开更多
In the process of thin-wall parts assembly for an antenna,the parts assembly deformation deviation is occurring due to the riveting assembly.In view of the riveting assembly deformation problems,it can be analyzed thr...In the process of thin-wall parts assembly for an antenna,the parts assembly deformation deviation is occurring due to the riveting assembly.In view of the riveting assembly deformation problems,it can be analyzed through transient and static simulation.In this work,the theoretical deformation model for riveting assembly is established with round head rivet.The simulation analysis for riveting deformation is carried out with the riveting assembly piece including four rivets,which comparing with the measuring points experiment results of riveting test piece through dealing with the experimental data using the point coordinate transform method and the space line fitting method.Simultaneously,the deformation deviation of the overall thin-wall parts assembly structure is analyzed through finite element simulation;and its results are verified by the measuring experiment for riveting assembly with the deformation deviation of some key points on the thin-wall parts.Through the comparison analysis,it is shown that the simulation results agree well with the experimental results,which proves the correctness and effectiveness of the theoretical analysis,simulation results and the given experiment data processing method.Through the study on the riveting assembly for thin-wall parts,it will provide a theoretical foundation for improving thin-wall parts assembly quality of large antenna in future.展开更多
The most general contact in mechanical transmission is the elliptical one. In particular, a toroidal continuously variable transmission (CVT) has an elliptical shape in the contact area under the elastohydrodynamic lu...The most general contact in mechanical transmission is the elliptical one. In particular, a toroidal continuously variable transmission (CVT) has an elliptical shape in the contact area under the elastohydrodynamic lubrication regime, where the shearing of the fluid subjects to high contact stress and transmits the power. Many parameters affect the contact service performance of the half toroidal CVT, which include the properties of the contacting material (Young抯 modulus), operating parameters (input torque and maximum traction coefficient) and geometrical parameters (aspect cavity ratio, curvature ratio and half cone angle of the power roller). In this paper, the contacts between the input disk, the power roller and the output disk are formulated using the classical Hertzian contact theory. Based on the formulated equations, different system parameters, which affect the maximum Hertzian stresses, are compared. The comparative results will provide some observations of the relations between the maximum Hertzian stresses and transmission ratios in the form of graphs. These graphs give useful information for designer to know the maximum Hertzian stress during operation in such systems.展开更多
文摘The electronic packaging box with high silicon aluminum-base alloy was prepared by semi-solid thixoforming technique.The flow characteristic of the Si phase was analyzed.The microstructures of different parts of the box were observed by optical microscopy and scanning electron microscopy,and the thermophysical and mechanical properties of the box were tested.The results show that there exists the segregation phenomenon between the primary Si phase and the liquid phase during thixoforming,the liquid phase flows from the box,and the primary Si phase accumulates at the bottom of the box.The volume fraction of primary Si phase decreases gradually from the bottom to the walls.Accordingly,the thermal conductivities of bottom center and walls are 107.6 and 131.5 W/（m·K）,the coefficients of thermal expansion（CTE） are 7.9×10-6 and 10.6×10-6 K-1,respectively.The flexural strength increases slightly from 167 to 180 MPa.The microstructures and properties of the box show gradient distribution overall.
文摘Gives a dynamic mathematical model of a typical type of multiple discs hydroviscous drive device which has been proved to be correct through tests.Utilizing the method of root-locus analysis the dynamic performance of this device is studied according to the model.Theoretical analysis and test re- suits show that the dynamic performance of the object of study can be greatly improved by speed negative feedback.
基金conducted within the framework of the project LNG-COMSHIP,Greek General Secretariat of Research and Technology Code:12CHN400,and was funded by the European Regional Development Fund(ERDF) and National Resources
文摘In this feasibility study, we investigate the viability of using Liquefied Natural Gas （LNG） fuel in an open type Ro-Ro passenger ferry and the associated potential challenges with regard to the vessel safety systems. We recommend an appropriate methodology for converting existing ships to run on LNG fuel, discuss all the necessary modifications to the ship’s safety systems, and also evaluate the relevant ship evacuation procedures. We outline the basic requirements with which the ship already complies for each safety system and analyze the additional restrictions that must be taken into consideration for the use of LNG fuel. Appropriate actions are recommended. Furthermore, we carry out a hazard identification study. Overall, we clearly demonstrate the technical feasibility of the investigated scenario. Minimal modifications to the ship’s safety systems are required to comply with existing safety rules for this specific type of ship.
基金Project(51675100)supported by the National Natural Science Foundation of ChinaProject(2016ZX04004008)supported by the National Numerical Control Equipment Major Project of ChinaProject(6902002116)supported by the Foundation of Certain Ministry of China
文摘In the process of thin-wall parts assembly for an antenna,the parts assembly deformation deviation is occurring due to the riveting assembly.In view of the riveting assembly deformation problems,it can be analyzed through transient and static simulation.In this work,the theoretical deformation model for riveting assembly is established with round head rivet.The simulation analysis for riveting deformation is carried out with the riveting assembly piece including four rivets,which comparing with the measuring points experiment results of riveting test piece through dealing with the experimental data using the point coordinate transform method and the space line fitting method.Simultaneously,the deformation deviation of the overall thin-wall parts assembly structure is analyzed through finite element simulation;and its results are verified by the measuring experiment for riveting assembly with the deformation deviation of some key points on the thin-wall parts.Through the comparison analysis,it is shown that the simulation results agree well with the experimental results,which proves the correctness and effectiveness of the theoretical analysis,simulation results and the given experiment data processing method.Through the study on the riveting assembly for thin-wall parts,it will provide a theoretical foundation for improving thin-wall parts assembly quality of large antenna in future.
基金the Ford-NSFC Foundation of China (No. 50122151).
文摘The most general contact in mechanical transmission is the elliptical one. In particular, a toroidal continuously variable transmission (CVT) has an elliptical shape in the contact area under the elastohydrodynamic lubrication regime, where the shearing of the fluid subjects to high contact stress and transmits the power. Many parameters affect the contact service performance of the half toroidal CVT, which include the properties of the contacting material (Young抯 modulus), operating parameters (input torque and maximum traction coefficient) and geometrical parameters (aspect cavity ratio, curvature ratio and half cone angle of the power roller). In this paper, the contacts between the input disk, the power roller and the output disk are formulated using the classical Hertzian contact theory. Based on the formulated equations, different system parameters, which affect the maximum Hertzian stresses, are compared. The comparative results will provide some observations of the relations between the maximum Hertzian stresses and transmission ratios in the form of graphs. These graphs give useful information for designer to know the maximum Hertzian stress during operation in such systems.
