Synthesizing the mechanical models of the belt, the driver and the take-up device, the dynamics model was established on the longitudinal vibration of the overall belt conveyor system with finite elemental method, and...Synthesizing the mechanical models of the belt, the driver and the take-up device, the dynamics model was established on the longitudinal vibration of the overall belt conveyor system with finite elemental method, and S-function simulation block of asynchronous motor owing feedback function was built in Matlab/Simulink software, the simulation block indicates that motor rotation speed and its output moment vary with load and time, and the motor is a dynamic feedback system in working process. The state space block was adopted to express model of the belt. Thus it created simulation model of established dynamic model of overall belt conveyor system with Mat- lab/Simulink software, and simulates the course of starting by properly setting simulation parameters, and processes data for visualization.展开更多
A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he ...A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he calculated iteratively. This model was compared with compliant slider and rigid stator model. The results of motor characteristics simulations showed that the motors based on this model would gain bigger stall torque. Then the friction and wear characteristics of two models were analyzed. The motors based on this model had lower coefficient of friction and better wear resistance.展开更多
The type of pinion and rack vertical shiplifts has been developed in recent a couple of years in the construction of dams.But the design methods and methodologies have rarely been discussed in literature.The Xiangjiab...The type of pinion and rack vertical shiplifts has been developed in recent a couple of years in the construction of dams.But the design methods and methodologies have rarely been discussed in literature.The Xiangjiaba shiplift is the second shiplift of this type following the Three Gorges shiplift.Being aimed at the technological rationality of the design in synthetically considering security,economy and applicability,this paper presents the research results of some vital issues relating the design of the Xiangjiaba shiplift,including the determination of design water depth of ship chamber based on fluid numeral computation and physical model test,the optimum design of general layout of main equipments and the civil structure of the Xiangjiaba shiplift,the finite element method(FEM) analysis of stress,vibration modes and the buckling of ship chamber,antiseismic research and the design of structures and mechanisms of the shiplift and the optimum design of driving mechanisms.This research provides the theoretical basis for the design of the Xiangjiaba shiplift.The design principles and research methods are valuable for the design of the same type of shiplifts.展开更多
According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restrain...According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restraint can be categorized into four states, namely, two-body lapping, three-body polishing, abrasive jet machining and fluid hydrodynamic shear stress machining. The critical transition condition of two-body lapping to three-body polishing was analyzed. The single abrasive material removal models of two-body lapping, three-body polishing, abrasive jet finishing and fluid hydrodynamic shear stress machining were proposed. Experiments were performed in the refited plane grinding machine for theoretical modes verification. It was found that experimental results agreed with academic modes and the modes validity was verified.展开更多
We have investigated the distribution of the electric field in p-i-n GaN avalanche photodiodes under different reverse bias values. type and separate absorption and multiplication （SAM） type We have also analyzed th...We have investigated the distribution of the electric field in p-i-n GaN avalanche photodiodes under different reverse bias values. type and separate absorption and multiplication （SAM） type We have also analyzed the influences of the parameters of each layer, including width and concentration, on the distribution of the electric field, especially on the breakdown voltage. It is found that a relatively high concentration of p-GaN （higher than 1×10^18 cm-3） and low cartier concentration of i-GaN （lower than 5×1016 cm-3） are helpful to restrict the electric field and reduce the breakdown voltage. In a SAM （p-i-n-i-n） structure, a suitable choice should be made for the concentration and thickness of the intermediate n-GaN layer in order to decrease breakdown voltage and prevent the device from degenerating into a p-i-n structure. Finally, the optimized material parameters of each layer are proposed.展开更多
文摘Synthesizing the mechanical models of the belt, the driver and the take-up device, the dynamics model was established on the longitudinal vibration of the overall belt conveyor system with finite elemental method, and S-function simulation block of asynchronous motor owing feedback function was built in Matlab/Simulink software, the simulation block indicates that motor rotation speed and its output moment vary with load and time, and the motor is a dynamic feedback system in working process. The state space block was adopted to express model of the belt. Thus it created simulation model of established dynamic model of overall belt conveyor system with Mat- lab/Simulink software, and simulates the course of starting by properly setting simulation parameters, and processes data for visualization.
基金Sponsored by the Natural Sciences Foundation of China (Grant No 50575055)the National 973 Key Development Project in Fundamental Science Research (Grant No2007CB607602)
文摘A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he calculated iteratively. This model was compared with compliant slider and rigid stator model. The results of motor characteristics simulations showed that the motors based on this model would gain bigger stall torque. Then the friction and wear characteristics of two models were analyzed. The motors based on this model had lower coefficient of friction and better wear resistance.
文摘The type of pinion and rack vertical shiplifts has been developed in recent a couple of years in the construction of dams.But the design methods and methodologies have rarely been discussed in literature.The Xiangjiaba shiplift is the second shiplift of this type following the Three Gorges shiplift.Being aimed at the technological rationality of the design in synthetically considering security,economy and applicability,this paper presents the research results of some vital issues relating the design of the Xiangjiaba shiplift,including the determination of design water depth of ship chamber based on fluid numeral computation and physical model test,the optimum design of general layout of main equipments and the civil structure of the Xiangjiaba shiplift,the finite element method(FEM) analysis of stress,vibration modes and the buckling of ship chamber,antiseismic research and the design of structures and mechanisms of the shiplift and the optimum design of driving mechanisms.This research provides the theoretical basis for the design of the Xiangjiaba shiplift.The design principles and research methods are valuable for the design of the same type of shiplifts.
基金Sponsored by the National Natural Science Foundation of China (Grant No 50475052)the Specialized Research Fund for the Doctoral Program of Higher Education (Grant No 20040145001)
文摘According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restraint can be categorized into four states, namely, two-body lapping, three-body polishing, abrasive jet machining and fluid hydrodynamic shear stress machining. The critical transition condition of two-body lapping to three-body polishing was analyzed. The single abrasive material removal models of two-body lapping, three-body polishing, abrasive jet finishing and fluid hydrodynamic shear stress machining were proposed. Experiments were performed in the refited plane grinding machine for theoretical modes verification. It was found that experimental results agreed with academic modes and the modes validity was verified.
基金supported by the National Science Fund for Distinguished Young Scholars (Grant No. 60925017)the National Natural Science Foundation of China (Grant Nos. 10990100,60836003 and 60776047)
文摘We have investigated the distribution of the electric field in p-i-n GaN avalanche photodiodes under different reverse bias values. type and separate absorption and multiplication （SAM） type We have also analyzed the influences of the parameters of each layer, including width and concentration, on the distribution of the electric field, especially on the breakdown voltage. It is found that a relatively high concentration of p-GaN （higher than 1×10^18 cm-3） and low cartier concentration of i-GaN （lower than 5×1016 cm-3） are helpful to restrict the electric field and reduce the breakdown voltage. In a SAM （p-i-n-i-n） structure, a suitable choice should be made for the concentration and thickness of the intermediate n-GaN layer in order to decrease breakdown voltage and prevent the device from degenerating into a p-i-n structure. Finally, the optimized material parameters of each layer are proposed.
