终端区进场流的路径选择研究

在实际运行中,通常依据管制员的经验对进场航班流的路径进行管理,缺乏科学性。针对终端区进场流的路径选择与进场排序的流量管理问题,以进场航班的总完成时间最短为目标,建立基于时间窗与位置约束的路径选择与排序的数学模型。采用先选择路径再排序的循环寻优的方法进行求解,将禁忌搜索(TS)与排序算法相结合,设计了TS-FCFS与TS-DP两种算法,着重建立了基于关键路径的邻域结构,并加入有效的重置(RESTAR)策略,使算法快速有效的收敛至最优解。最后借助SIMMOD仿真平台验证算法的可行性。以北京首都机场21架航班为例,仿真结果显示,TS-FCFS与TS-DP两种方法较原计划的进场路径总完成时间分别节约了149s与175s。该路径选择算法降低了进场时间,提高了终端区进场效率。通过合理优化进场航班流的路径选择与进场排序,平衡了跑道负荷,减少了航空器间潜在的冲突,同时为管制员调配进场航班流提供了合理有效的路径选择建议。

A novel computational method for protein-protein interaction networks prediction of alpha-synuclein

Alpha-synuclein plays an important role in Parkinson's disease(PD).The current study of alpha-synuclein mainly concentrates at the gene level.However, it is found that the study at the protein level has special significance.Meanwhile, there is free information on the Internet, such as databases and algorithms of protein-protein interactions(PPIs).In this paper, a novel method which integrates distributed heterogeneous data sources and algorithms to predict PPIs for alpha-synuclein in silico is proposed.The PPIs generated by the method take advantage of various experimental data, and indicate new information about PPIs for alpha-synuclein.In the end of this paper, the result illustrates that the method is practical.It is hoped that the prediction result obtained by this method can provide guidance for biological experiments of PPIs for alpha-synuclein to reveal possible mechanisms of PD.

Experimental and FEM Study of Coated and Uncoated Tools Used for Dry Milling of Compacted Graphite Cast Iron

Compacted graphite cast iron （CG1） has been the material for high-power diesel engines recently, but its increased strength causes poor machinability. In this study, coated and uncoated carbide tools were used in dry milling experiment and FEM simulation to study the machinability of CGI and wear behaviour of tools. The experimental and FEM simulation results show that coated tool has great advantage in dry milling of CGI. SEM and EDS analysis of tool wear indicate the wear morphology and wear mechanism. Adhesive wear is the main mechanism to cause un- coated tool wear, while abrasive wear and delamination wear are the main mechanism to cause coated tool wear. Stress and temperature distribution in FEM simulation help to understand the wear mechanism including the reason for coat- ing peeled off.

Developments in the understanding of gas–solid contact efficiency in the circulating fluidized bed riser reactor:A review

In the last several decades, circulating fluidized bed reactors have been studied in many aspects including hydrodynamics, heat and mass transfer and gas–solid two phase contacting. However, despite the abundance of review papers on hydrodynamics, there is no summary paper on gas–solid contact efficiency to date, especially on high density circulating fluidized beds(CFBs). This paper gives an introduction to, and a review of the measurement of contact efficiency in circulating fluidized bed riser. Firstly, the popular testing method of contact efficiency including the method of heating transfer experiment and hot model reaction are discussed, then previous published papers are reviewed based on the discussed methods. Some key results of the experimental work are described and discussed. Gas–solid contact efficiency is affected by the operating conditions as well as the particle size distribution. The result of the contact efficiency shows that the CFB riser is far away from an ideal plug flow reactor due to the characteristics of hydrodynamics in the riser. Lacunae in the available literature have been delineated and recommendations have been made for further work.

Laboratory and field experiment on measurement of soil thermal conductivity by probe method

The authors presented a new measuring method of the soil thermal conductivity,the probe method,which is designed and made based on the theory of line heat source. This method is used to measure thermal conductivity of coarse sand,fine sand and silty clay in different water contents. The results that measured by the probe method are well consistent with those of QTM-D_2. The soil thermal conductivity increases in different levels with the increase of the water content. Compared the soil thermal conductivity measured by the probe method in laboratory with in-situ experiment,it shows that the measuring gap gradually increases with the increase of the depth. The reason is that the in-situ measuring thermal conductivity can reflect the actual situation of the soil mass.

Research on accurate quantitation technique using liquid chromatography coupled with triple quadrupole mass spectrometry and experiment optimization—take a novel diuretic as an example

Liquid chromatography coupled with the triple quadrupole mass spectrometry(LC-QQQ MS)technique is the most commonly used technique for quantitative analysis.It is widely used in pharmacology,targeted metabolomics,Chinese medicine quality control,and other research fields.The technique monitors only characteristic precursors and product ions through multiple reaction monitoring(MRM)mode and can detect targeted molecules in complex matrix with high specificity and sensitivity.In the present study,a diarylamide derivative diuretic was used as an example to introduce the method establishment and parameter optimization of this liquid chromatography-mass spectrometry technique.Diuretic and its internal standard could be completely separated within a 5-min gradient,and the quantitative linear range was 1–1000 ng/mL with R2=0.9996 in practical samples.This study showed that the key to the method development for LC-QQQ MS was the selection of the LC mobile phase,the elution gradient,the declustering potential,and the collision energy of compounds in MS.

Real-time compaction quality monitoring of high core rockfill dam

The conventional quality control method of core rocldill dam construction exhibit difficulty controlling compaction parameters accurately or ensuring construction quality. This is because it is easily influenced by human behavior or lack of adequate management. We therefore establish the timely monitoring indexes and control criteria of compaction processes by considering the characteristics and quality requirements of high core rockffll dam construction. Based on the established indexes and criteria, integrating GPS, GPRS and PDA technologies, a real-time compaction quality monitoring method is proposed. The relevant key techniques are proposed as well, including automatic collection of information and a graphic algorithm for rolling-process visualization. By the proposed method and techniques, a real-time monitoring system is provided to realize the precise automatic online entire-process monitoring of compaction parameters, including compaction pass, rolling trajectory, nmning speed of roller, vibration status and rolled pavement thickness. The application of the Nuozhadu project shows that the proposed system can control compaction parameters effectively and ensure better construction quality. Therefore, it might become a new way towards construction quality control of high core rockfill dam.