冲击力对提升机安全制动力矩的影响分析及油压值的计算

由于煤矿生产规模和井筒布置方式不同,施工立井深度及井筒直径也会不同。在立井凿井过程中,出矸任务不同,导致提升荷载不断变化,所以必须对提升机和电机进行配套计算。因此,分析了立井凿井提升系统中冲击力对安全制动力矩的影响,探讨了提升系统质量模数Z与安全制动力矩倍数K的关系,给出了K值的选取方法,提出了立井凿井提升制动力矩的选定和油压值的计算方法。

Cancelling ore pillars in large-scale coastal gold deposit: A case study in Sanshandao gold mine, China

According to the actual conditions in Sanshandao Gold Mine, the cancelling ore pillars mining method was researched. Firstly, a series of tests for the physical and mechanical characteristics of rock mass were carried out and a quality classification system of rock mass applied in coastal metal deposit was established. Secondly, the reasonable demarcation depth of cancelling ore pillars was simulated using the finite element method, and the simulation results show that the ore pillars can be cancelled below the level of-555 m. Thirdly, a novel layer-backfill mining method of room-pillar alternation was designed to reduce the disturbance and settlement of terrain in mining area. Engineering practice shows that the new mining method enhanced the mining output and relieved rock disturbance. Furthermore, the settlement of the roof strata was small and no disaster occurred. The new mining technology effectively controlled the deformation of the terrain, indicating that the mining of the large-scale gold coastal deposit in Sanshandao Gold Mine was achieved safely, efficiently, and with a low loss rate.

Effect of geometrical parameters on forming quality of high-strength TA18 titanium alloy tube in numerical control bending

The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clarified by finite element simulation. The results show that the distribution of wall thickness change ratio Δt and cross section deformation ratio ΔD are very similar under different β; the Δt and ΔD decrease with the increase of R/D, and to obtain the qualified bent tube, the R/D must be greater than 2.0; the wall thinning ratio Δto slightly increases with larger D and t, while the wall thickening ratio Δti and ΔD increase with the larger D and smaller t; the Δto and ΔD firstly decrease and then increase, while the Δti increases, for the same D/t with the increase of D and t.

斜井提升机上提载荷紧急制动

斜井提升机是矿井提升机的一种,主要应用在中小型矿井的副斜井、轨道暗斜井和轨道上下山的提升运输上。斜井提升机的质量模数与减速度、提升钢丝绳存在的弹性变形、极小坡度工况的停车等因素有关,这些现象在理论计算中可能被工程简化或忽略不计,但它们的存在或多或少对实际生产有一些影响,对其进行分析、探讨,可方便读者在生产实践中,充分认识其工作原理,杜绝事故,保证安全生产。

提升机安全制动力矩的选取和油压的计算

阐述了矿井提升机安全制动力矩倍数K与提升系统质量模数M的关系,探讨了K值的选取方法,提出了适合于各种提升方式的制动力矩和油压的计算和选定方法。

GEOTHERMAL RESOURCES ASSESSMENT AND NUMERICAL SIMULATION IN TUANBO REGION

This paper mainly deals with the reservoir on the heat and mass transfer and mass and energy balance in a geothermal field.On the basis of briefing the general characteristics of the reservoir and the supposition of the reservoir modeling,the paper emphasizes the mathematical descriptions of hydra thermal transportation and convection by two methods according to the different models,such as lumped parameter model and distributed parameter model.It is effective to use these models in simulating the heterogeneous,and anisotropical fracture reservoir for the designed lifetime of 15 years.

Coupled Reaction/Distillation Process for Hydrolysis of Methyl Acetate

A process composed of a fixed-bed and a distillation column with a side withdraw, mainly methanol, is developed to hydrolyze methyl acetate (MA) as a typical byproduct in polyvinyl alcohol (PVA) and pure terephthalic acid (PTA) factory. The process is simulated by employing the equilibrium stage model RadFrac and plug flow model Rplug in Aspen Plus. Experiments are also carried out in a lab-scale to evaluate the process. The results show that at the molar ratio of water to methyl acetate about 4.0-5.0 in the feed stream and the volume ratio of distillate to feed MA above a critical value, the side product contains more than 80% (by mass) (MeOH) and less than 2% (by mass) MA, while the bottom contains more than 46% (by mass) acetic acid (HAc) and less than 0.5% (by mass) methanol with almost complete conversion of MA. Compared with the old catalytic distillation process we proposed before, this process can cut down 47.6% energy consumption and a distillation column.

A New Calculation of the In-Medium Quark Condensate at Finite Density and Temperature

The in-medium quark condensate is studied with an equivalent-mass approach in which one does not need to make assumptions on the derivatives of model parameters with respect to the quark current mass.It is shown that the condensate is generally a decreasing function of both the density and temperature with the decreasing speed depending on the confinement parameter.Specially,at given density,the condensate decreases on increasing temperature.The decreasing speed is comparatively small at lower temperature,and becomes very fast at higher temperature.

Parameter identification and pressure control of dynamic system in shield tunneling using least squares method

An estimation approach using least squares method was presented for identificationof model parameters of pressure control in shield tunneling.The state equation ofthe pressure control system for shield tunneling was analytically derived based on themass equilibrium principle that the entry mass of the pressure chamber from cutting headwas equal to excluding mass from the screw conveyor.The randomly observed noise wasnumerically simulated and mixed to simulated observation values of system responses.The numerical simulation shows that the state equation of the pressure control system forshield tunneling is reasonable and the proposed estimation approach is effective even ifthe random observation noise exists.The robustness of the controlling procedure is validatedby numerical simulation results.

Fluid-solid coupling numerical simulation of charge process in variable-mass thermodynamic system

Abstract： A joint solution model of variabk：-mass flow in two-phase region and fluid-solid coupling heat transfer, concerned about the charge process of variable-mass thermodynamic system, is built up and calculated by the finite element method （FEM）. The results are basically consistent with relative experimental data. The calculated average heat transfer coefficient reaches 1.7~105 W/（m2. K）. When the equal percentage valve is used, the system needs the minimum requirements of valve control, but brings the highest construction cost. With the： decrease of initial steam pressure, the heat transfer intensity also weakens but the steam flow increases. With the initial water filling coefficient increasing or the temperature of steam supply decreasing, the amount of accumulative steam flow increases with the growth of steam pressure. When the pressure of steam supply drops, the steam flow gradient increases during the maximum opening period of control valve, and causes the maximum steam flow to increase.

Numerical simulation study on the thermal environment in heading face

Based on κ-ε turbulence model, the distributions of the velocity field, tempera- ture field, thermal comfort index, PMV-PPD （Predicted Mean Vote-Predicted Percentage Dissatisfied）, and air quality index, mean age of air were obtained of Zhouyuanshan Coal Mine in -650 m level of a heading face by CFD（Computational Fluid Dynamics）software, Airpak 2.0. Moreover, the human thermal comfort and the air quality of the heading face were analyzed with PMV-PPD and mean age of air indices, which received an intuitive visualization and accurate evaluation results. In order to create a safe, comfortable, and economical underground operating environment, a scientific, rational, and comprehensive prediction and evaluation needed to provide a theoretical and technical basis for coal mine ventilation, cooling, heat harm treatment, and prevention. Meanwhile, from the human thermal comfort and air quality to research the underground environment, it embodied the concept of being human oriented.

Heat and hazardous contaminant transports in ventilated high-rise industrial halls

Performances and efficiencies of displacement ventilation(DV) and partial ventilation(PV) for industrial halls of different configurations as well as the heat and mass transports within the industrial halls were numerically investigated. Three levels of Rayleigh number(5.8×1010, 1.0×1012 and 2.1×1012) and two values of source contaminant flux(5 mg/s and 50 mg/s) were considered. The inlet Reynolds numbers were 2×104, 5×104, 1.5×105 and 4.5×105 for DV and 5×105, 1×106, 2×106 and 4×106 for PV, respectively. From the results, it is concluded that the above parameters have very complex impacts on the conjugated heat and mass transports. From points of view of acceptable indoor air quality and ventilation efficiency, PV at Re=1×106 with side-located sources and 65% of the supply air extracted through floor level outlets is the best choice when Ra=5.8×1010. However, DVs at Re=5×104 and Re=1.5×105with center-located sources and floor-mounted air suppliers are the best choices for Ra=1.0×1012 and Ra=2.1×1012, respectively. When source contaminant flux reaches 50 mg/s, local extraction as a supplement of general ventilation is recommended. The results can be a first approximation to 3D numerical investigation and preliminary ventilation system design guidelines for high-rise industrial halls.

Measurement of Mass Transfer Coefficients and Their Modelling of Continuous Counter-Current Aqueous Two-Phase System in a Packed Extraction Column

Overall dispersed side volumetric mass transfer coefficients for protein and amino acids were measured in continuous countercurrent PEG4000/KHP aqueous two-phase systems in a 57mm I.D. packed extraction column. A model for overall dispersed side volumetric mass transfer coefficients was derived by describing the motion of the drops based upon Navier-Stokes equation combined with the relationship between mass transfer coefficients and the drop velocity. The model provides good predictions and can be successfully used in aqueous two-phase extraction. The average relative deviation between calculated values and experimental data ranges from 8% to 14%.

Optimal location and effect judgment on drainage tunnels for landslide prevention

An optimal drainage tunnel location determination method for landslide prevention was proposed to solve the existing problems in drainage tunnel construction. Current applications of drainage tunnel systems in China were reviewed and the fimctions of drainage tunnel were categorized as catchment and interception. Numerical simulations were conducted. The results show that both catchment and interception tunnels have variation of the function in the simulation of monolayer model, which shows the reduction of permeability condition in lower layer. The function of catchment can be observed in the deep slope, while the function of interception is observed near groundwater source. By using the slope safety factor and discharge water amount as the objectives of optimal drainage tunnel location, and pore-water pressure in fixed node and section flux as the judgment for construction quality of adjacent drainage tunnel, the design principle of drainage tunnel was introduced. The K103 Landslide was illustrated as an example to determine the optimal drainage tunnel location. The measured drainage tunnel efficiency was evaluated and compared with that from the numerical analyses based on groundwater data. The results validate the present numerical study.

Difference of Directions Between External Driving Force and Movement Direction of Center of Mass

Driven dynamics of a two-dimensional Frenkel-Kontorova model is studied in the paper.In our numericalsimulations, it is found that the movement direction of the center of mass is not consistent with that of the externaldriving force except for some special symmetric directions at the lower driving force.Our results also indicate that themovement direction of the center of mass strongly depends on both the magnitude and the direction of the externaldriving force as well as the misfit angle between two layers.

A theoretical analysis of vertical dynamic response of large-diameter pipe piles in layered soil

Considering the viscous damping of the soil and soil-pile vertical coupled vibration,a computational model of large-diameter pipe pile in layered soil was established.The analytical solution in frequency domain was derived by Laplace transformation method.The responses in time domain were obtained by inverse Fourier transformation.The results of the analytical solution proposed agree well with the solutions in homogenous soil.The effects of the shear modulus and damping coefficients of the soil at both outer and inner sides of the pipe pile were researched.The results indicate that the shear modulus of the outer soil has more influence on velocity admittance than the inner soil.The smaller the shear modulus,the larger the amplitude of velocity admittance.The velocity admittance weakened by the damping of the outer soil is more obvious than that weakened by the damping of the inner soil.The displacements of the piles with the same damping coefficients of the outer soil have less difference.Moreover,the effects of the distribution of soil layers are analyzed.The results indicate that the effect of the upper soil layer on dynamic response of the pipe pile is more obvious than that of the bottom soil layer.A larger damping coefficient of the upper layer results in a smaller velocity admittance.The dynamic response of the pipe pile in layered soil is close to that of the pipe pile in homogenous soil when the properties of the upper soil layer are the same.

Effects of h-BN content on properties of Ni-Cr/h-BN composite

Ni-Cr/h-BN self-lubricating composities were prepared by powder metallurgy (P/M) method.The effects of hexagonal boron nitride (h-BN) content on the mechanical and tribological properties of the Ni-Cr/h-BN composites were investigated.The corresponding frictional models were established to analyze the formation of the lubricant h-BN films on the surfaces of the Ni-Cr/h-BN composites.The results show that,when the content of h-BN increases from 5% to 15% (mass fraction),the bending strength of the Ni-Cr/h-BN composite decreases from 96.670 MPa to 17.319 MPa,and the hardness (HB) decreases from 33 to 14.The friction coefficient of the Ni-Cr/h-BN composite decreases firstly from 0.385 to 0.216,and then increases to 0.284,while the wear rate decreases firstly from 4.14×10-9 kg/(N·m) to 1.35×10-9 kg/(N·m),then increases to 2.36×10-9 kg/(N·m).The best comprehensive mechanical and tribological properties can be obtained between 10% and 12% h-BN addition.

An improved CFD model of gas flow and particle interception in a fiber material

An improved CFD model of gas flow and particle interception in a fiber material which fiber size is Y-shape was developed in this work. The porous medium model was used to build the model of the whole size of fiber filter medium. Mixture model was adopted. The algorithm of particle interception in the whole size of fiber filter medium was derived and UDF(User Defined Function) that described kinds of particle filtering mechanisms in filter fibrous media was added to the Fluent default conservation equation as source term for simulation. The inertial resistance of the filter was taken into consideration, which provided a more precise measurement of the smoke flow and the particle interception in the filter under higher smoke speed conditions. The commercial software, Fluent 6.3, was used to simulate the smoke flow and particle interception in the filter in a single suction. The velocity and pressure profiles of smoke or nicotine particle in the filter, as well as nicotine particle volume fraction profile were well simulated. Finally, the comparisons of nicotine particle filtration efficiency between Fluent simulation results in this work and experimental results, as well as the model prediction in the literature were made to validate the simulation model. The comparisons showed that the particle entrapment model from simulation results was in good agreement with that from the experimental results. In addition, the Fluent simulation results are closer to reality both at the beginning and the end of the smoke process comparing with the model predicted results in the literature.

Combinatorial model of solute transport in porous media

Modeling of solute transport is a key issue in the area of soil physics and hydrogeology. The most common approach (the convection-dispersion equation) considers an average convection flow rate and Fickian-like dispersion. Here,we propose a solute transport model in porous media of continuously expanding scale, according to the combinatorics principle. The model supposed actual porous media as a combinative body of many basic segments. First, we studied the solute transport process in each basic segment body, and then deduced the distribution of pore velocity in each basic segment body by difference approximation, finally assembled the solute transport process of each basic segment body into one of the combinative body. The simulation result coincided with the solute transport process observed in test. The model provides useful insight into the solute transport process of the non-Fickian dispersion in continuously expanding scale.

The Application of Improved Fuzzy Comprehensive Evaluation method in Practice Teaching Quality Evaluation System

According to the theory of fuzzy mathematics, Fuzzy comprehensive evaluation method of the original algorithm is improved, and reduced the possibility loss of the original evaluation data. The improved algorithm is applied in the practice teaching quality evaluation system, and improved the practice teaching quality evaluation results and the accuracy of visual, and promote the teaching management scientific, standardized and institutionalized. In order to establish incentive mechanism, it can bring a positive role to improve teaching quality.