The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning elec...The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning electron microscopy （SEM） with energy dispersive X-ray spectrometry, and electron probe micro-analysis （EPMA）. The results showed that the grains of aluminum alloy were significantly refined and secondary phases were dispersed and distributed uniformly at the grain boundaries, due to ultrasonic treatment （UST）. By EPMA, it was observed that the distribution of the main elements A1, Zn, Mg and Cu was more homogeneous in alloys with UST, than in alloys without UST. The mechanical properties of the aluminum alloy also significantly improved. As demonstrated by the SEM fractography of the fractured faces of several castings, fracture of the unrefined specimens occurred in a brittle manner, whereas the cracks of the refined specimens showed quasi-cleavage fracture.展开更多
he effects of porous hydroxyapatite blocks（PHABs） and an adjunct low-intensity pulsed ultrasound stimulation（LIPUS） on the fusion rate in a rabbit spinal posterolateral fusion（PLF） model were evaluated.Twenty ra...he effects of porous hydroxyapatite blocks（PHABs） and an adjunct low-intensity pulsed ultrasound stimulation（LIPUS） on the fusion rate in a rabbit spinal posterolateral fusion（PLF） model were evaluated.Twenty rabbits underwent PLF with autograft and PHABs were randomly assigned to two groups：treated group with 20 min LIPUS daily and untreated control group for 4 weeks until euthanasia.The fused motion segments were subjected to manual palpation,gross observation,and radiographic investigation before histomorphologic and scanning electron microscopic analyses.Statistical differences between the LIPUS group and the control group are found in the fusion rate,bone density gray scale,trabecular bone formation,osteoblast-like cells,chondrocytes and positive expression of BMP-2 and TGF-β1 in the junction zone（significance level p〈0.05）.The results suggest that LIPUS can increase fusion rates and accelerate bone in-growth into PHAB.Hence,PHAB and LIPUS may be used together to increase fusion rates in a rabbit spinal fusion model with a promising extension to human application.展开更多
To obtain the refined electrodeposited nickel layer on AZ91D magnesium alloy,ultrasonic technology was applied in the processes of pre-treatment and electrodeposition.The phases of pre-treatment layer and the nickel c...To obtain the refined electrodeposited nickel layer on AZ91D magnesium alloy,ultrasonic technology was applied in the processes of pre-treatment and electrodeposition.The phases of pre-treatment layer and the nickel coating were analyzed by X-ray diffractometry(XRD)and X-ray photoelectron spectroscopy(XPS),and the microstructure was observed by scanning electron microscopy(SEM).Then,the effects of ultrasonic dispersion on the microstructure of pre-treatment layer and the grain refinement of electrodeposited nickel layer were discussed.The results showed that the pre-treatment electrodeposited Cu-Sn layer with compact microstructure could be synthesized in alkaline copper-tin liquid with ultrasonic agitation,as a result,smooth and refined nickel coating formed on AZ91D magnesium alloy.On the other hand,preferred orientation in the coating decreased because of the refined grains.展开更多
A method of dry grinding muscovite based on the use of knife-mills is reported.It was possible to produce mica with a particle size below 100 and 45μm.After grinding,the samples were submitted to sonication treatment...A method of dry grinding muscovite based on the use of knife-mills is reported.It was possible to produce mica with a particle size below 100 and 45μm.After grinding,the samples were submitted to sonication treatment,which promoted delamination of the material.The particle size distribution shows that sonicated mica has more particles in the size range 10-50μm than does non-sonicated mica have. This also indicates a decrease in the average particle size.Characterization of the treated muscovite by scanning electron microscopy revealed a highly delaminated material with a plate-like structure.The products were characterized by chemical analysis and X-ray diffraction,too.This mica has already been used for the synthesis of pearlescent pigments.展开更多
Ni-Co alloys were electroplated from sulphate electrolyte using addition agents including sodium gluconate, boric acid and eysteine on copper foil by the galvanostatic technique and ultrasound waves. The chemical comp...Ni-Co alloys were electroplated from sulphate electrolyte using addition agents including sodium gluconate, boric acid and eysteine on copper foil by the galvanostatic technique and ultrasound waves. The chemical composition, surface morphologies, crystalline structure and hardness of the Ni-Co alloys were studied using energy dispersive spectroscopy, scanning electron microscope, X-ray diffraction and Vickers testing method, respectively. The effect of current density and addition agents on the microstructure and morphology of Ni-Co alloys were examined. The appropriate concentration of additives and ultrasound waves were found to produce fine and smooth crystals leading to higher hardness of Ni-Co alloys. The microhardness of the Ni-Co alloys was varied between 4860-7530 HV. The surface morphology of coatings was changed from granular to fine due to using of gluconate, boric acid, cysteine and ultrasound waves. The mechanical properties of nanocrystalline Ni-Co alloys showed an increase of the hardness with the growing of Ni content in the alloy. The X-ray diffraction studies indicated that nanocrystalline structure was face-centred cubic for pure Ni and Ni-Co alloys with Co content in the range of 1-75 wt.%. A hexagonal closed-package structure was obtained for pure Co and Ni-Co alloys with the cobalt content with range of 75-99 wt.%.展开更多
Scanning near-field acoustic microscope （SNAM） combines the ultrasonic detection technology with scanning near-field microscopy. The main characteristic of such microscope is that the acoustic wave is produced or de...Scanning near-field acoustic microscope （SNAM） combines the ultrasonic detection technology with scanning near-field microscopy. The main characteristic of such microscope is that the acoustic wave is produced or detected in near-field area whether ultrasonic transducer acts as generator or detector. The resolution of SNAM can reach to nanometer scale. First, two typical SNAMs, scanning electron acoustic Inicroscope and scanning probe acoustic microscope, will be introduced in this paper. The working principle of our homemade SNAM based on a commercial scanning probe microscope will be reported, together with some recent results from this homemade SNAM.展开更多
基金Project(2016GK1004)supported by the Science and Technology Major Project of Hunan Province,China
文摘The effect of an ultrasonic field on the microstructure and mechanical properties of 7085 aluminum alloy during solidification was investigated by optical microscopy, Vickers hardness test, tensile test, scanning electron microscopy （SEM） with energy dispersive X-ray spectrometry, and electron probe micro-analysis （EPMA）. The results showed that the grains of aluminum alloy were significantly refined and secondary phases were dispersed and distributed uniformly at the grain boundaries, due to ultrasonic treatment （UST）. By EPMA, it was observed that the distribution of the main elements A1, Zn, Mg and Cu was more homogeneous in alloys with UST, than in alloys without UST. The mechanical properties of the aluminum alloy also significantly improved. As demonstrated by the SEM fractography of the fractured faces of several castings, fracture of the unrefined specimens occurred in a brittle manner, whereas the cracks of the refined specimens showed quasi-cleavage fracture.
文摘he effects of porous hydroxyapatite blocks（PHABs） and an adjunct low-intensity pulsed ultrasound stimulation（LIPUS） on the fusion rate in a rabbit spinal posterolateral fusion（PLF） model were evaluated.Twenty rabbits underwent PLF with autograft and PHABs were randomly assigned to two groups：treated group with 20 min LIPUS daily and untreated control group for 4 weeks until euthanasia.The fused motion segments were subjected to manual palpation,gross observation,and radiographic investigation before histomorphologic and scanning electron microscopic analyses.Statistical differences between the LIPUS group and the control group are found in the fusion rate,bone density gray scale,trabecular bone formation,osteoblast-like cells,chondrocytes and positive expression of BMP-2 and TGF-β1 in the junction zone（significance level p〈0.05）.The results suggest that LIPUS can increase fusion rates and accelerate bone in-growth into PHAB.Hence,PHAB and LIPUS may be used together to increase fusion rates in a rabbit spinal fusion model with a promising extension to human application.
文摘To obtain the refined electrodeposited nickel layer on AZ91D magnesium alloy,ultrasonic technology was applied in the processes of pre-treatment and electrodeposition.The phases of pre-treatment layer and the nickel coating were analyzed by X-ray diffractometry(XRD)and X-ray photoelectron spectroscopy(XPS),and the microstructure was observed by scanning electron microscopy(SEM).Then,the effects of ultrasonic dispersion on the microstructure of pre-treatment layer and the grain refinement of electrodeposited nickel layer were discussed.The results showed that the pre-treatment electrodeposited Cu-Sn layer with compact microstructure could be synthesized in alkaline copper-tin liquid with ultrasonic agitation,as a result,smooth and refined nickel coating formed on AZ91D magnesium alloy.On the other hand,preferred orientation in the coating decreased because of the refined grains.
文摘A method of dry grinding muscovite based on the use of knife-mills is reported.It was possible to produce mica with a particle size below 100 and 45μm.After grinding,the samples were submitted to sonication treatment,which promoted delamination of the material.The particle size distribution shows that sonicated mica has more particles in the size range 10-50μm than does non-sonicated mica have. This also indicates a decrease in the average particle size.Characterization of the treated muscovite by scanning electron microscopy revealed a highly delaminated material with a plate-like structure.The products were characterized by chemical analysis and X-ray diffraction,too.This mica has already been used for the synthesis of pearlescent pigments.
文摘Ni-Co alloys were electroplated from sulphate electrolyte using addition agents including sodium gluconate, boric acid and eysteine on copper foil by the galvanostatic technique and ultrasound waves. The chemical composition, surface morphologies, crystalline structure and hardness of the Ni-Co alloys were studied using energy dispersive spectroscopy, scanning electron microscope, X-ray diffraction and Vickers testing method, respectively. The effect of current density and addition agents on the microstructure and morphology of Ni-Co alloys were examined. The appropriate concentration of additives and ultrasound waves were found to produce fine and smooth crystals leading to higher hardness of Ni-Co alloys. The microhardness of the Ni-Co alloys was varied between 4860-7530 HV. The surface morphology of coatings was changed from granular to fine due to using of gluconate, boric acid, cysteine and ultrasound waves. The mechanical properties of nanocrystalline Ni-Co alloys showed an increase of the hardness with the growing of Ni content in the alloy. The X-ray diffraction studies indicated that nanocrystalline structure was face-centred cubic for pure Ni and Ni-Co alloys with Co content in the range of 1-75 wt.%. A hexagonal closed-package structure was obtained for pure Co and Ni-Co alloys with the cobalt content with range of 75-99 wt.%.
基金supported by the National Natural Science Foundation of China (Grant Nos.50971011 and 10874006)Beijing Natural Science Foundation (Grant No.1102025)Research Fund for the Doctoral Program of Higher Education of China (Grant No.20091102110038)
文摘Scanning near-field acoustic microscope （SNAM） combines the ultrasonic detection technology with scanning near-field microscopy. The main characteristic of such microscope is that the acoustic wave is produced or detected in near-field area whether ultrasonic transducer acts as generator or detector. The resolution of SNAM can reach to nanometer scale. First, two typical SNAMs, scanning electron acoustic Inicroscope and scanning probe acoustic microscope, will be introduced in this paper. The working principle of our homemade SNAM based on a commercial scanning probe microscope will be reported, together with some recent results from this homemade SNAM.
