Effects of cold rolling followed by annealing on microstructural evolution and superelastic properties of the Ti50Ni48Co2 shape memory alloy were investigated. Results showed that during cold rolling, the alloy micros...Effects of cold rolling followed by annealing on microstructural evolution and superelastic properties of the Ti50Ni48Co2 shape memory alloy were investigated. Results showed that during cold rolling, the alloy microstructure evolved through six basic stages including stress-induced martensite transformation and plastic deformation of martensite, deformation twinning, accumulation of dislocations along twin and variant boundaries in martensite, nanocrystallization, amorphization and reverse transformation of martensite to austenite. After annealing at 400 ℃ for 1 h, the amorphous phase formed in the cold-rolled specimens was completely crystallized and an entirely nanocrystalline structure was achieved. The value of stress level of the upper plateau in this nanocrystalline alloy was measured as high as 730 MPa which was significantly higher than that of the coarse-grained Ni50Ti50 and Ti50Ni48Co2 alloys. Moreover, the nanocrystalline Ti50Ni48Co2 alloy had a high damping capacity and considerable efficiency for energy storage.展开更多
Effects of thermomechanical treatment of cold rolling followed by annealing on microstructure and superelastic behavior of the Ni50Ti50 shape memory alloy were studied.Several specimens were produced by copper boat va...Effects of thermomechanical treatment of cold rolling followed by annealing on microstructure and superelastic behavior of the Ni50Ti50 shape memory alloy were studied.Several specimens were produced by copper boat vacuum induction melting.The homogenized specimens were hot rolled and annealed at 900°C.Thereafter,annealed specimens were subjected to cold rolling with different thickness reductions up to 70%.Transmission electron microscopy revealed that the severe cold rolling led to the formation of a mixed microstructure consisting of nanocrystalline and amorphous phases in Ni50Ti50 alloy.After annealing at 400°C for 1 h,the amorphous phase formed in the cold-rolled specimens was crystallized and a nanocrystalline structure formed.Results showed that with increasing thickness reduction during cold rolling,the recoverable strain of Ni50Ti50 alloy was increased during superelastic experiments such that the 70%cold rolled-annealed specimen exhibited about 12%of recoverable strain.Moreover,with increasing thickness reduction,the critical stress for stress-induced martensitic transformation was increased.It is noteworthy that in the 70%cold rolled-annealed specimen,the damping capacity was measured to be 28 J/cm3 that is significantly higher than that of commercial NiTi alloys.展开更多
Huge calculation burden and difficulty in convergence are the two central conundrums of nonlinear topology optimization(NTO).To this end,a multi-resolution nonlinear topology optimization(MR-NTO)method is proposed bas...Huge calculation burden and difficulty in convergence are the two central conundrums of nonlinear topology optimization(NTO).To this end,a multi-resolution nonlinear topology optimization(MR-NTO)method is proposed based on the multiresolution design strategy(MRDS)and the additive hyperelasticity technique(AHT),taking into account the geometric nonlinearity and material nonlinearity.The MR-NTO strategy is established in the framework of the solid isotropic material with penalization(SIMP)method,while the Neo-Hookean hyperelastic material model characterizes the material nonlinearity.The coarse analysis grid is employed for finite element(FE)calculation,and the fine material grid is applied to describe the material configuration.To alleviate the convergence problem and reduce sensitivity calculation complexity,the software ANSYS coupled with AHT is utilized to perform the nonlinear FE calculation.A strategy for redistributing strain energy is proposed during the sensitivity analysis,i.e.,transforming the strain energy of the analysis element into that of the material element,including Neo-Hooken and second-order Yeoh material.Numerical examples highlight three distinct advantages of the proposed method,i.e.,it can(1)significantly improve the computational efficiency,(2)make up for the shortcoming that NTO based on AHT may have difficulty in convergence when solving the NTO problem,especially for 3D problems,(3)successfully cope with high-resolution 3D complex NTO problems on a personal computer.展开更多
Metamaterials with higher-order topological band gaps that exhibit topological physics beyond the bulkedge correspondence provide unique application values due to their ability of integrating topological boundary stat...Metamaterials with higher-order topological band gaps that exhibit topological physics beyond the bulkedge correspondence provide unique application values due to their ability of integrating topological boundary states at multiple dimensions in a single chip.On the other hand,in the past decade,micromechanical metamaterials are developing rapidly for various applications such as micro-piezoelectricgenerators,intelligent micro-systems,on-chip sensing and self-powered micro-systems.To empower these cutting-edge applications with topological manipulations of elastic waves,higher-order topological mechanical systems working at high frequencies(MHz)with high quality-factors are demanded.The current realizations of higher-order topological mechanical systems,however,are still limited to systems with large scales(centimetres)and low frequencies(k Hz).Here,we report the first experimental realization of an on-chip micromechanical metamaterial as the higher-order topological insulator for elastic waves at MHz.The higher-order topological phononic band gap is induced by the band inversion at the Brillouin zone corner which is achieved by configuring the orientations of the elliptic pillars etched on the silicon chip.With consistent experiments,theory and simulations,we demonstrate the emergence of coexisting topological edge and corner states in a single silicon chip as induced by the higher-order band topology.The experimental realization of on-chip micromechanical metamaterials with higherorder topology opens a new regime for materials and applications based on topological elastic waves.展开更多
文摘Effects of cold rolling followed by annealing on microstructural evolution and superelastic properties of the Ti50Ni48Co2 shape memory alloy were investigated. Results showed that during cold rolling, the alloy microstructure evolved through six basic stages including stress-induced martensite transformation and plastic deformation of martensite, deformation twinning, accumulation of dislocations along twin and variant boundaries in martensite, nanocrystallization, amorphization and reverse transformation of martensite to austenite. After annealing at 400 ℃ for 1 h, the amorphous phase formed in the cold-rolled specimens was completely crystallized and an entirely nanocrystalline structure was achieved. The value of stress level of the upper plateau in this nanocrystalline alloy was measured as high as 730 MPa which was significantly higher than that of the coarse-grained Ni50Ti50 and Ti50Ni48Co2 alloys. Moreover, the nanocrystalline Ti50Ni48Co2 alloy had a high damping capacity and considerable efficiency for energy storage.
文摘Effects of thermomechanical treatment of cold rolling followed by annealing on microstructure and superelastic behavior of the Ni50Ti50 shape memory alloy were studied.Several specimens were produced by copper boat vacuum induction melting.The homogenized specimens were hot rolled and annealed at 900°C.Thereafter,annealed specimens were subjected to cold rolling with different thickness reductions up to 70%.Transmission electron microscopy revealed that the severe cold rolling led to the formation of a mixed microstructure consisting of nanocrystalline and amorphous phases in Ni50Ti50 alloy.After annealing at 400°C for 1 h,the amorphous phase formed in the cold-rolled specimens was crystallized and a nanocrystalline structure formed.Results showed that with increasing thickness reduction during cold rolling,the recoverable strain of Ni50Ti50 alloy was increased during superelastic experiments such that the 70%cold rolled-annealed specimen exhibited about 12%of recoverable strain.Moreover,with increasing thickness reduction,the critical stress for stress-induced martensitic transformation was increased.It is noteworthy that in the 70%cold rolled-annealed specimen,the damping capacity was measured to be 28 J/cm3 that is significantly higher than that of commercial NiTi alloys.
基金supported by the National Natural Science Foundation of China(Grant Nos.11902085 and 11832009)the Science and Technology Association Young Scientific and Technological Talents Support Project of Guangzhou City(Grant No.SKX20210304)the Natural Science Foundation of Guangdong Province(Grant No.2021Al515010320).
文摘Huge calculation burden and difficulty in convergence are the two central conundrums of nonlinear topology optimization(NTO).To this end,a multi-resolution nonlinear topology optimization(MR-NTO)method is proposed based on the multiresolution design strategy(MRDS)and the additive hyperelasticity technique(AHT),taking into account the geometric nonlinearity and material nonlinearity.The MR-NTO strategy is established in the framework of the solid isotropic material with penalization(SIMP)method,while the Neo-Hookean hyperelastic material model characterizes the material nonlinearity.The coarse analysis grid is employed for finite element(FE)calculation,and the fine material grid is applied to describe the material configuration.To alleviate the convergence problem and reduce sensitivity calculation complexity,the software ANSYS coupled with AHT is utilized to perform the nonlinear FE calculation.A strategy for redistributing strain energy is proposed during the sensitivity analysis,i.e.,transforming the strain energy of the analysis element into that of the material element,including Neo-Hooken and second-order Yeoh material.Numerical examples highlight three distinct advantages of the proposed method,i.e.,it can(1)significantly improve the computational efficiency,(2)make up for the shortcoming that NTO based on AHT may have difficulty in convergence when solving the NTO problem,especially for 3D problems,(3)successfully cope with high-resolution 3D complex NTO problems on a personal computer.
基金supported by the Natural Science Foundation of Guangdong Province(2020A1515010549)China Postdoctoral Science Foundation(2020M672615 and 2019M662885)+1 种基金National Postdoctoral Program for Innovative Talents(BX20190122)the Jiangsu specially-appointed professor funding。
文摘Metamaterials with higher-order topological band gaps that exhibit topological physics beyond the bulkedge correspondence provide unique application values due to their ability of integrating topological boundary states at multiple dimensions in a single chip.On the other hand,in the past decade,micromechanical metamaterials are developing rapidly for various applications such as micro-piezoelectricgenerators,intelligent micro-systems,on-chip sensing and self-powered micro-systems.To empower these cutting-edge applications with topological manipulations of elastic waves,higher-order topological mechanical systems working at high frequencies(MHz)with high quality-factors are demanded.The current realizations of higher-order topological mechanical systems,however,are still limited to systems with large scales(centimetres)and low frequencies(k Hz).Here,we report the first experimental realization of an on-chip micromechanical metamaterial as the higher-order topological insulator for elastic waves at MHz.The higher-order topological phononic band gap is induced by the band inversion at the Brillouin zone corner which is achieved by configuring the orientations of the elliptic pillars etched on the silicon chip.With consistent experiments,theory and simulations,we demonstrate the emergence of coexisting topological edge and corner states in a single silicon chip as induced by the higher-order band topology.The experimental realization of on-chip micromechanical metamaterials with higherorder topology opens a new regime for materials and applications based on topological elastic waves.
