超微力发生系统及其电容采集模块的设计

阐述了静电场复现微小力值的原理及实验方法;设计了超微力发生装置,并在此基础上提出了超微力发生系统;超微力发生的原理表明,电容采集模块是超微力发生系统的关键模块。根据超微力发生装置结构,选用USB控制芯片CY7C68013和电容采集芯片AD7747,设计了基于USB2.0的电容采集电路,编写了固件和上位机控制程序实现了电容数据的采集和保存;进行了电容梯度测量实验。

扫描力显微镜中超微力的探测方法

本文介绍了近十年来，各国科学家在研究扫描力显微镜的过程中所采用的各种超微力（１０￣（－８）～１０￣（－１０）Ｎ）传感器的探测方法。评述了各种方法的灵敏度，抗振性，使用范围，操作方式和各自的优缺点。并对最近出现的几种新的探测方法作了说明。

Effects of ultrasonic treatment on microstructure and mechanical properties of Mg-5Zn-2Er alloy

The effects of ultrasonic treatment on the microstructure and mechanical properties of Mg-5Zn-2Er alloy at room temperature （RT） and high temperature （HT） were investigated. The microstructure and mechanical properties of the samples were studied by OM, SEM and MTS material tester. The results show that the microstructure and mechanical properties are improved after the ultrasonic vibration. The best effects of ultrasonic vibration on microstructure and mechanical properties were obtained with the ultrasonic vibration power of 600 W and time of 100 s. The cavitation and acoustic streaming caused by ultrasonic treatment play a major role in refining the microstructure and increasing mechanical properties of the alloy.

Effects of ultrasonic treatment on microstructure and mechanical properties of Mg-6Zn-0.5Y-2Sn alloy

The effects of the ultrasonic treatment on the microstructure and mechanical properties of Mg-6Zn-0.5Y-2Sn alloy were investigated. The results show that the ultrasonic treatment has significant effect on the microstructure and mechanical properties of Mg-6Zn-0.5Y-2Sn alloy. The phases in Mg-6Zn-0.5Y-2Sn alloy are α-Mg, MgZn2, MgSnY, Mg2Sn, and a small amount of I-phase. With the application of ultrasonic treatment, I-phase nearly disappears, and with increasing the ultrasonic treatment power, the coarse dendrites gradually change into roundish equiaxed grains. The second phases at the α-Mg boundaries transform from coarse, semicontinuous and non-uniform to fine, discontinuous, uniform and dispersive. When the ultrasonic treatment power is 700 W, the best comprehensive mechanical properties of Mg-6Zn-0.5Y-2Sn alloy are obtained. Compared with the untreated alloy, the 0.2%tensile yield strength, ultimate tensile strength and elongation are improved by 28%, 30%and 67%, respectively.

Microstructure, mechanical and oxidation characteristics of detonation gun and HVOF sprayed MCrAlYX coatings

Microstructure, mechanical property and oxidation resistance of MCrAlYX coatings prepared by detonation gun (D-gun) and HVOF spraying were investigated. Lamellar microstructure and uniform microstructure formed in D-gun sprayed MCrAlYX coating and HVOF sprayed coating, respectively. Element redistribution and formation of new phase took place during the detonation process. Besides, the porosity of D-gun sprayed coating was much lower than that of HVOF sprayed coating. On the mechanical property, the micro-hardnesses of the two coatings were in the same level (~HV 910). However, D-gun sprayed MCrAlYX coating exhibited larger standard deviation of microhardness due to its lamellar microstructure, and exhibited better bend bonding strength owing to the existence of residual compressive stress between the layers and particles. Meanwhile, due to the much more compact microstructure, D-gun sprayed MCrAlYX coating showed superior oxidation resistance to the HVOF sprayed coating. The continuous dense protective layer can form earlier in D-gun sprayed coating and thus suppress further oxidation and control the oxide thickness at a relatively low level.

Effects of nano-SiC_p content on microstructure and mechanical properties of SiC_p/A356 composites assisted with ultrasonic treatment

nano-SiCp/A356 composites with different nano-SiCp contents were prepared by squeeze casting after ultrasonic treatment（UT）. The effects of SiCp content on the microstructure and mechanical properties of the nanocomposites were investigated. Theresults show that with the addition of nano-SiCp, the microstructure of nanocomposites is obviously refined, the morphology of theα（Al） grains transforms from coarse dendrites to rosette crystals, and long acicular eutectic Si phases are shortened and rounded. Themechanical properties of 0.5%, 1% and 2% （mass fraction） SiCp/A356 nanocomposites are improved continuously with the increaseof nano-SiCp content. Especially, when the SiCp content is 2%, the tensile strength, yield strength and elongation are 259 MPa,144 MPa and 5.3%, which are increased by 19%, 69% and 15%, respectively, compared with those of the matrix alloy. Theimprovement of strength is attributed to mechanisms of Hall？Petch strengthening and Orowan strengthening.

Supercritical Antisolvent Precipitation of Microparticles of Quercetin

Supercritical antisolvent (SAS) process is a recently developed technology to produce micro- and nano particles. This paper presents a continuous apparatus to conduct experiment of SAS process. With the apparatus, the effects of pressure, temperature and flow ratio of CO2 to the solution on the shape and size of particles are studied for the quercetin-ethanol-CO2 system. Spherical quercetin microparticles with diameters ranging form 1 μm to 6μm can be obtained while ethanol is used as organic solvent. The most effective fact on the shape and size of particles is pressure, the next is temperature and the last is the flow ratio of CO2 to solution.

Mechanical properties and microstructural evolution of ultrafine grained zircaloy-4 processed through multiaxial forging at cryogenic temperature

The mechanical properties and microstructural evolution of zircaloy-4 subjected to cumulative strains of 1.48,2.96,4.44 and 5.91 through multiaxial forging（MAF） at cryogenic temperature（77 K） were investigated.The mechanical properties of the MAF treated alloy were measured through universal tensile testing and Vickers hardness testing equipment.The zircaloy-4 deformed up to a cumulative strain of 5.91 showed improvement in both ultimate tensile strength and hardness from 474 MPa to 717 MPa and from HV 190 to HV 238,respectively,as compared with the as-received alloy.However,there was a noticeable decrement in ductility（from 18%to 3.5%） due to the low strain hardening ability of deformed zircaloy-4.The improvement in strength and hardness of the deformed alloy is attributed to the grain size effect and higher dislocation density generated during multiaxial forging.The microstructural evolutions of deformed samples were characterized by optical microscopy and transmission electron microscopy（TEM）.The evolved microstructure at a cumulative strain of 5.91 obtained after MAF up to 12 cycles depicted the formation of ultrafine grains with an average size of 150-250 nm.

Adaptive Lagrange finite element methods for high precision vibrations and piezoelectric acoustic wave computations in SMT structures and plates with nano interfaces

This paper discusses the validity of (adaptive) Lagrange generalized plain finite element method (FEM) and plate element method for accurate analysis of acoustic waves in multi-layered piezoelectric structures with tiny interfaces between metal electrodes and surface mounted piezoelectric substrates. We have come to conclusion that the quantitative relationships between the acoustic and electric fields in a piezoelectric structure can be accurately determined through the proposed finite element methods. The higher-order Lagrange FEM proposed for dynamic piezoelectric computation is proved to be very accurate (prescribed relative error 0.02% - 0.04% ) and a great improvement in convergence accuracy over the higher order Mindlin plate element method for piezoelectric structural analysis due to the assumptions and corrections in the plate theories.The converged lagrange finite element methods are compared with the plate element methods and the computedresults are in good agreement with available exact and experimental data. The adaptive Lagrange finite elementmethods and a new FEA computer program developed for macro- and micro-scale analyses are reviewed, and recently extended with great potential to high-precision nano-scale analysis in this paper and the similarities between piezoelectric and seismic wave propagations in layered structures and plates are stressed.

Effect of jet milling on micro-strain behavior and rupture behavior of agglomerates of ultrafine WC powders

The Williamson-Hall and uniaxial compression methods were used to study the variations of the micro-strain and stress-strain relations in WC powders after jet milling and ball milling, respectively. The rupture behavior of agglomerates in WC powders was investigated. Meanwhile, the as-obtained WC powders treated by different milling methods were used to fabricate WC-10%Co cemented carbides, followed by the performance assessment of cemented carbides. The results show that the micro-strain of the jet-milled WC powders decreases significantly compared with that of the ball-milled WC powders, and that the cemented carbides prepared by jet-milled WC powders exhibit excellent properties with a transverse-rupture strength of 4260 MPa, due to the elimination of agglomerates and the reduction of lattice strain.

Process−microstructure−properties relationship in Al−CNTs−Al2O3 nanocomposites manufactured by hybrid powder metallurgy and microwave sintering process

Al−2CNTs−xAl2O3 nanocomposites were manufactured by a hybrid powder metallurgy and microwave sintering process.The correlation between process-induced microstructural features and the material properties including physical and mechanical properties as well as ultrasonic parameters was measured.It was found that physical properties including densification and physical dimensional changes were closely associated with the morphology and particle size of nanocomposite powders.The maximum density was obtained by extensive particle refinement at milling time longer than 8 h and Al2O3 content of 10 wt.%.Mechanical properties were controlled by Al2O3 content,dispersion of nano reinforcements and grain size.The optimum hardness and strength properties were achieved through incorporation of 10 wt.%Al2O3 and homogenous dispersion of CNTs and Al2O3 nanoparticles(NPs)at 12 h of milling which resulted in the formation of high density of dislocations and extensive grain size refinement.Also both longitudinal and shear velocities and attenuation increase linearly by increasing Al2O3 content and milling time.The variation of ultrasonic velocity and attenuation was attributed to the degree of dispersion of CNTs and Al2O3 and also less inter-particle spacing in the matrix.The larger Al2O3 content and more homogenous dispersion of CNTs and Al2O3 NPs at longer milling time exerted higher velocity and attenuation of ultrasonic wave.

Experimental Study on the Surface Modification of Ultra Thin DLC Films

Surface modification of Diamond-like carbon (DLC) films was carried out in order to estimate the reliability of the ultra thin DLC films. The wear resistance, conductivity and mechatronic reliability of the films were studied by contact atomic force microscope (AFM), electric force microscope (EFM) and conductive AFM. The failure mechanism of pits formed and the reason for conductivity changed of DLC films were examined.

Study on high speed tension property of B-grade bulletproof steel

In this paper, the high speed tension experiments have been performed on ultra high strength bulletproof steel. The specimen were cut from B-grade bulletproof steel sheet after hard-module quenching with thickness of 2.3 mm. The mechanical properties at strain rates of 0.001 s^-1, 0.01 s^-1, 0.1 s^-1 and 1 s^-1 were carried out on MTSS10, while those at higher strain rates of 200 s^-1, 500 s^-1 and i 000 s^-1 were tested on HTM5020 high speed tension tester and Hopkinson bar. The data from the high speed tension experiments were fitted via Johnson-Cook constitutive equation, and the fracture surface of each specimen was analyzed by scanning electron microscope （SEM）. The results indicate that, the shoot resistance capability of bulletproof steel is closely related to its strength, thickness and flow behaviors under high strain rate. The shoot resistance will be improved in the case of higher strength and better matching between strength and elongation. The Johnson-Cook constitutive equation fitted via experimental data provides fundament to numerical simulation. With the increase of strain rate, the size and depth of dimple trend to decrease and the depth of dimple changes less in steel with lower strength and higher elongation. The SEM analysis of fracture aspect is of benefit for further understanding of deformation and fracture mode under high strain rate.

Microstructure and mechanical properties of VAlN/Si_(3)N_(4) nano-multilayer coatings

VAlN coating is of particular interest for dry cutting applications owing to its low-friction and excellent abrasiveness.Nano-multilayer structure is designed to tailor the properties of VAlN coating.In this work,a series of VAlN/Si_(3)N_(4) nano-multilayer coatings with varied Si_(3)N_(4) layer thicknesses were prepared by reactive sputtering method.The microstructure and mechanical properties of the coatings were both investigated.It is revealed that Si_(3)N_(4) with a shallow thickness(~0.4 nm)was crystallized and grown coherently with VAlN,showing a remarkable increase in hardness compared to VAlN monolayer coating.The hardness of coherently VAlN/Si_(3)N_(4) nano-multilayer coatings reached to 48.7 GPa.With further increase of Si_(3)N_(4) layer thickness,the coherent growth of nano-multilayers was terminated,showing amorphous structure formed in nano-multilayers and the hardness was declined.On the other hand,when Si_(3)N_(4) layer thickness was 0.4 nm,the friction coefficient of VAlN/Si_(3)N_(4) nano-multilayer coating was almost equal to that of VAlN monolayer coating,which was attributed to the crystallization of Si_(3)N_(4) and the produced coherent interfaces between VAlN and Si_(3)N_(4) for the hardening effect of nano-multilayer coatings.Upon further increase of Si_(3)N_(4) layer thickness,pronounced improvement of friction coefficient in VAlN/Si_(3)N_(4) nano-multilayer coating was observed.

An automated AFM for nanoindentation and force related measurements

A fully automated atomic force microscope(AFM)is presented.The mechanical motion of the AFM stage was controlled by three steppers.The fine motion of the AFM was controlled by an MCL one-axis piezo plate.A32.768kHz crystal tuning fork(TF)was used as the transducer with a probe attached.An acoustic sensor was used to measure the interactions between the probe and the sample.An SR850lock-in amplifier was used to monitor the TF signals.An additional lock-in amplifier was used to monitor the acoustic signal.A field programmable gate array(FPGA)board was used to collect the data in automatic mode.The main controller was coded with LabVIEW,which was in charge of Z-axis scan,signal processing and data visualization.A manual mode and an automatic mode were implemented in the controller.Users can switch the two modes at any time during the operation.This AFM system showed several advantages during the test operations.It is simple,flexible and easy to use.

Chemical Solution Deposition of YBa2Cu3O7 Films on YSZ （100） Substrates

We report the epitaxial growth of YBCO （YBa2Cu3O7） films on YSZ （Yttria-stabilized Zirconia） （100） substrates by chemical solution deposition. The precursor solution was prepared by dissolving stoichiometric amounts of acetates of Y（OOCCH3）3·4H2O, Ba（OOCCH3）2 and Cu（OOCCH3）·2H2O in an aqueous solution of oxalic acid （H2C2O4） and following the sol-gel route. This solution was directly dripped onto YSZ （100） substrates with the help of a Fisher pipette. To form the YBCO film, the sample was crystallized by annealing at 860 ℃ for 12 h in an oxidizing atmosphere. The characterization was performed by XRD （X-ray diffraction） analysis which revealed high intensity （001） reflections and denoted that most of the grains were c-axis oriented. Randomly oriented grains and other phases such as Y2BaCuO5 and CuO were also detected. The superconducting YBCO phase is demonstrated from the susceptibility versus temperature measurements which indicate a superconducting critical temperature ≈ 90 K. In addition, a surface morphology analysis was performed by optical microscopy and atomic force microscopy which revealed an average roughness of 0.2197 μm.

Effects of Vapor Pressure and Super-Hydrophobic Nanocomposite Coating on Microelectronics Reliability

Modeling vapor pressure is crucial for studying the moisture reliability of microelectronics, as high vapor pressure can cause device failures in environments with high temperature and humidity. To minimize the impact of vapor pressure, a super-hydrophobic(SH) coating can be applied on the exterior surface of devices in order to prevent moisture penetration. The underlying mechanism of SH coating for enhancing device reliability, however, is still not fully understood. In this paper, we present several existing theories for predicting vapor pressure within microelectronic materials. In addition, we discuss the mechanism and effectiveness of SH coating in preventing water vapor from entering a device, based on experimental results. Two theoretical models, a micro-mechanics-based whole-field vapor pressure model and a convection-diffusion model, are described for predicting vapor pressure. Both methods have been successfully used to explain experimental results on uncoated samples. However, when a device was coated with an SH nanocomposite, weight gain was still observed, likely due to vapor penetration through the SH surface. This phenomenon may cast doubt on the effectiveness of SH coatings in microelectronic devices. Based on current theories and the available experimental results, we conclude that it is necessary to develop a new theory to understand how water vapor penetrates through SH coatings and impacts the materials underneath. Such a theory could greatly improve microelectronics reliability.

D-term Chaotic Braneworld in Supergravity Constrained by WMAP9 Data

We study a supergravity D-term chaotic inflationary model, in the context of the braneworld scenario, in particular we consider the Randal1-Sundrum model type 2. Using the latest release from the combination of WMAP9, eCMB, BAO, and Ho, we show that the inflation observables depend only on the number ore-folds N. We also derive all known spectrum inflationary parameters, which are widely consistent with WMAP9 data for a particular choice of values N specially for the scalar spectral index ns and the ratio r. However, the running of the scalar spectral index dns/dlnk is now excluded from the range given by the latest observational measurements.

High efficiency and enhanced ESD properties of UV LEDs by inserting p-GaN/p-AlGaN superlattice

Significantly improved electrostatic discharge （ESD） properties of InGaN/GaN-based UV light-emitting diode （LED） with in- serting p-GaN/p-A1GaN superlattice （p-SLs） layers （instead of p-A1GaN single layer） between multiple quantum wells and Mg-doped GaN layer are reported. The pass yield of the LEDs increased from 73.53% to 93.81% under negative 2000 V ESD pulses. In addition, the light output power （LOP） and efficiency droop at high injection current were also improved. The mechanism of the enhanced ESD properties was then investigated. After excluding the effect of capacitance modulation, high-resolution X-ray diffraction （XRD） and atomic force microscope （AFM） measurements demonstrated that the dominant mechanism of the enhanced ESD properties is the material quality improved by p-SLs, which indicated less leakage paths, ra- ther than the current spreading improved by p-SLs.

High conductive graphene assembled films with porous micro-structure for freestanding and ultra-low power strain sensors

Graphene emerges as an ideal material for constructing high-performance strain sensors,due to its superior mechanical property and high conductivity.However,in the process of assembling graphene into macroscopic materials,its conductivity decreases significantly.Also,tedious fabrication process hinders the application of graphene-based strain sensors.In this work,we report a freestanding graphene assembled film(GAF)with high conductivity((2.32±0.08)×105 S m-1).For the sensitive materials of strain sensors,it is higher than most of reported carbon nanotube and graphene materials.These advantages enable the GAF to be an ultra-low power consumption strain sensor for detecting airflow and vocal vibrations.The resistance of the GAF remains unchanged with increasing temperature(20-100℃),exhibiting a good thermal stability.Also,the GAF can be used as a strain sensor directly without any flexible substrates,which greatly simplifies the fabrication process in comparison with most reported strain sensors.Additionally,the GAF used as a pressure sensor with only^4.7μW power is investigated.This work provides a new direction for the preparation of advanced sensors with ultra-low power consumption,and the development of flexible and energy-saving electronic devices.