The vibration characteristics of transverse oscillation of an axially moving beam with high velocity is in- vestigated. The vibration equation and boundary conditions of the free-free axially moving beam are derived u...The vibration characteristics of transverse oscillation of an axially moving beam with high velocity is in- vestigated. The vibration equation and boundary conditions of the free-free axially moving beam are derived using Hamilton＇s principle. Furthermore, the linearized equations are set up based on Galerkinl s method for the ap- proximation solution. Finally, three influencing factors on the vibration frequency of the beam are considered： （1） The axially moving speed. The first order natural frequency decreases as the axial velocity increases, so there is a critical velocity of the axially moving beam. （2） The mass loss. The changing of the mass density of some part of the beam increases the beam natural frequencies. （3） The thermal effect.＇ The temperature increase will decrease the beam elastic modulus and induce the vibration frequencies descending.展开更多
The forming of elliptic motions on the modal conversion ultrasonic motors （MCUMs） is discussed. The principles of the modal conversion are investigated based on the coupling with the stator and the rotor, and using ...The forming of elliptic motions on the modal conversion ultrasonic motors （MCUMs） is discussed. The principles of the modal conversion are investigated based on the coupling with the stator and the rotor, and using an independent coupler. The elliptical locus observed on the longitudinal-torslonal vibration converter with oblique slits is analyzed by using vibration theory. A method for the modal conversion is proposed by using the local mode of a substructure On a main structure. The method can be used to design the modal conversion type ultrasonic motors.展开更多
A two-degree-of-freedom（2-DOF） linear ultrasonic motor （USM） consists of a cylinder-shaped stator and a slider. Two bending vibration modes with orthogonality and one longitudinal vibration mode are excited in the...A two-degree-of-freedom（2-DOF） linear ultrasonic motor （USM） consists of a cylinder-shaped stator and a slider. Two bending vibration modes with orthogonality and one longitudinal vibration mode are excited in the stator by three groups of piezoelectric ceramic elements. The combinations of any one bending mode and the longitudinal mode mentioned above push the slider to move linearly in direction x or y. Some key issues for improving the motor output properties and efficiency are given. They include selection of the vibration modes, consistency of the modal frequencies, placement of the piezoelectric ceramic elements and the supporting plane, setting of pre-pressure, and influence of interfering modes.展开更多
A new type of linear ultrasonic motor with two degrees of freedom (DOF) motion is presented. The concept of the new typical motor is based on the combination of a longitudinal and two bending modes. The construction a...A new type of linear ultrasonic motor with two degrees of freedom (DOF) motion is presented. The concept of the new typical motor is based on the combination of a longitudinal and two bending modes. The construction and the operational principle of motor are described, and the elliptical motion of the driving point of the actuator is proved. Meanwhile, a prototype linear motor is designed by using the finite element method (FEM) and is constructed for experiments. The vibration modes are tested with the laser doppler vibrometer (PSV-300F), and the experimental results prove that the design requirements on the mode shape of the actuator and nature frequency are satisfied. The test run of the motor indicates that the operational principle of the motor and the design results are correct, and the output properties are also tested.展开更多
This paper investigates the passing events between electric bicycles and conventional bicycles and explores the relationships between passing events and traffic parameters in bicycle facilities.Three exclusive bicycle...This paper investigates the passing events between electric bicycles and conventional bicycles and explores the relationships between passing events and traffic parameters in bicycle facilities.Three exclusive bicycle paths in Nanjing, China,were observed with cameras.Then,the field data including vehicle number,velocity characteristics and passing event features were analyzed in detail.Data analysis and fitting reveal that the speed difference has little impact on the passing event number,as does the bicycle ratio.The Gaussian function can better describe the relationship between the passing event number and bicycle volume （density）.The valid use level of bicycle path width influences the inflexion of the passing events-density fitting curve.The conclusions can be applied for estimating the passing events in mixed bicycle flows and for choosing a suitable width of separate bicycle path.展开更多
Generally, super Brownian motion will not c on verge vaguely to 0 if the initial measure is sufficiet large, so it is very inte resting to get asymptotic estimation for super Brownian motion. In this paper, w e will p...Generally, super Brownian motion will not c on verge vaguely to 0 if the initial measure is sufficiet large, so it is very inte resting to get asymptotic estimation for super Brownian motion. In this paper, w e will prove two asymptotic for super Brownian motion with general critical bran ching mechanism.展开更多
A novel cooling system combining ultra fast cooling rigs with laminar cooling devices was investigated.Based on the different cooling mechanisms,a serial of mathematic models were established to describe the relations...A novel cooling system combining ultra fast cooling rigs with laminar cooling devices was investigated.Based on the different cooling mechanisms,a serial of mathematic models were established to describe the relationship between water flow and spraying pressure and the relationship between water spraying heat flux and layout of nozzles installed on the top and bottom cooling headers.Model parameters were validated by measured data.Heat transfer models including air convection model,heat radiation model and water cooling capacity model were detailedly introduced.In addition,effects on cooling capacity by water temperature and different valve patterns were also presented.Finally,the comparison results from UFC used or not have been provided with respect to temperature evolution and mechanical properties of Q235B steel grade with thickness of 7.8 mm.Since online application of the sophisticated CTC process control system based on these models,run-out table cooling control system has been running stably and reliably to produce resource-saving,low-cost steels with smaller grain size.展开更多
In this paper, we investigate the interacting super-Brownian motion depending on population size. This process can be viewed as the high density limit of a sequence of particle systems with branching mechanism dependi...In this paper, we investigate the interacting super-Brownian motion depending on population size. This process can be viewed as the high density limit of a sequence of particle systems with branching mechanism depending on their population size. We will construct a limit function-valued dual process.展开更多
To explore the relationship between such a construct and an existing continence score. METHODSA retrospective study of incontinent patients who underwent anal physiology (AP) was performed. AP results and Cleveland Cl...To explore the relationship between such a construct and an existing continence score. METHODSA retrospective study of incontinent patients who underwent anal physiology (AP) was performed. AP results and Cleveland Clinic Continence Scores (CCCS) were extracted. An anal physiology score (APS) was developed using maximum resting pressures (MRP), anal canal length (ACL), internal and external sphincter defects and pudendal terminal motor latency. Univariate associations between each variable, APS and CCCS were assessed. Multiple regression analyses were performed. RESULTSOf 508 (419 women) patients, 311 had both APS and CCCS measured. Average MRP was 51 mmHg (SD 23.2 mmHg) for men and 39 mmHg (19.2 mmHg) for women. Functional ACL was 1.7 cm for men and 0.7 cm for women. Univariate analyses demonstrated significant associations between CCCS and MRP (P = 0.0002), ACL (P = 0.0006) and pudendal neuropathy (P < 0.0001). The association between APS and CCCS was significant (P < 0.0001) but accounted for only 9.2% of the variability in CCCS. Multiple regression showed that the variables most useful in predicting CCCS were external sphincter defect, pudendal neuropathy and previous pelvic surgery, but only improving the scores predictive ability to 12.5%. CONCLUSIONThis study shows that the ability of AP tests to predict continence scores improves when considered collectively, but that a constructed summation model before and after multiple regression is poor at predicting the variability in continence scores.展开更多
NIOSH ground control safety research program at Spokane,Washington,is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being us...NIOSH ground control safety research program at Spokane,Washington,is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First,photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application.Second,field photogrammetric data is compared to crackmeter data from a deep underground mine.Accuracies were found to average 8 mm,but have produced results within 0.2 mm of true displacement,as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation.Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.展开更多
Micro- injury （exercise-induced muscle damage, EIMD） will cause a temporary decline in muscle function, if not handled properly, it could cause more serious injury or overtraining, and even lead to the end of the at...Micro- injury （exercise-induced muscle damage, EIMD） will cause a temporary decline in muscle function, if not handled properly, it could cause more serious injury or overtraining, and even lead to the end of the athletes ＇ sports life. However, some studies have shown that an appropriate period of eccentric exercise training resulted in EIMD while promoted heart muscle fiber hypertrophy and corresponding muscle growth faster than exercise training, and there are the typical ＂ repetitive training effect＂ , ie after a period of the EIMD recovery, the muscle＇ s injury or delayed onset muscle soreness （DOMS） caused by the same movement is significantly reduced. So its deep study could help to guide the athlete to avoid or mitigate the negative effects which brought by EIMD, while could help to further clarify the process of the body to adapt to exercise training or mechanism.展开更多
基金Supported by the National Natural Science Foundation of China(10972104)~~
文摘The vibration characteristics of transverse oscillation of an axially moving beam with high velocity is in- vestigated. The vibration equation and boundary conditions of the free-free axially moving beam are derived using Hamilton＇s principle. Furthermore, the linearized equations are set up based on Galerkinl s method for the ap- proximation solution. Finally, three influencing factors on the vibration frequency of the beam are considered： （1） The axially moving speed. The first order natural frequency decreases as the axial velocity increases, so there is a critical velocity of the axially moving beam. （2） The mass loss. The changing of the mass density of some part of the beam increases the beam natural frequencies. （3） The thermal effect.＇ The temperature increase will decrease the beam elastic modulus and induce the vibration frequencies descending.
基金Supported by the National Natural Science Foundation of China(10874090,50775109)the Jiangsu Provincial High-Tech Project of China(BG2006005)~~
文摘The forming of elliptic motions on the modal conversion ultrasonic motors （MCUMs） is discussed. The principles of the modal conversion are investigated based on the coupling with the stator and the rotor, and using an independent coupler. The elliptical locus observed on the longitudinal-torslonal vibration converter with oblique slits is analyzed by using vibration theory. A method for the modal conversion is proposed by using the local mode of a substructure On a main structure. The method can be used to design the modal conversion type ultrasonic motors.
文摘A two-degree-of-freedom（2-DOF） linear ultrasonic motor （USM） consists of a cylinder-shaped stator and a slider. Two bending vibration modes with orthogonality and one longitudinal vibration mode are excited in the stator by three groups of piezoelectric ceramic elements. The combinations of any one bending mode and the longitudinal mode mentioned above push the slider to move linearly in direction x or y. Some key issues for improving the motor output properties and efficiency are given. They include selection of the vibration modes, consistency of the modal frequencies, placement of the piezoelectric ceramic elements and the supporting plane, setting of pre-pressure, and influence of interfering modes.
文摘A new type of linear ultrasonic motor with two degrees of freedom (DOF) motion is presented. The concept of the new typical motor is based on the combination of a longitudinal and two bending modes. The construction and the operational principle of motor are described, and the elliptical motion of the driving point of the actuator is proved. Meanwhile, a prototype linear motor is designed by using the finite element method (FEM) and is constructed for experiments. The vibration modes are tested with the laser doppler vibrometer (PSV-300F), and the experimental results prove that the design requirements on the mode shape of the actuator and nature frequency are satisfied. The test run of the motor indicates that the operational principle of the motor and the design results are correct, and the output properties are also tested.
基金The National Natural Science Foundation of China(No.51238008,51408322)
文摘This paper investigates the passing events between electric bicycles and conventional bicycles and explores the relationships between passing events and traffic parameters in bicycle facilities.Three exclusive bicycle paths in Nanjing, China,were observed with cameras.Then,the field data including vehicle number,velocity characteristics and passing event features were analyzed in detail.Data analysis and fitting reveal that the speed difference has little impact on the passing event number,as does the bicycle ratio.The Gaussian function can better describe the relationship between the passing event number and bicycle volume （density）.The valid use level of bicycle path width influences the inflexion of the passing events-density fitting curve.The conclusions can be applied for estimating the passing events in mixed bicycle flows and for choosing a suitable width of separate bicycle path.
文摘Generally, super Brownian motion will not c on verge vaguely to 0 if the initial measure is sufficiet large, so it is very inte resting to get asymptotic estimation for super Brownian motion. In this paper, w e will prove two asymptotic for super Brownian motion with general critical bran ching mechanism.
基金Project(51034009)supported by the National Natural Science Foundation of China
文摘A novel cooling system combining ultra fast cooling rigs with laminar cooling devices was investigated.Based on the different cooling mechanisms,a serial of mathematic models were established to describe the relationship between water flow and spraying pressure and the relationship between water spraying heat flux and layout of nozzles installed on the top and bottom cooling headers.Model parameters were validated by measured data.Heat transfer models including air convection model,heat radiation model and water cooling capacity model were detailedly introduced.In addition,effects on cooling capacity by water temperature and different valve patterns were also presented.Finally,the comparison results from UFC used or not have been provided with respect to temperature evolution and mechanical properties of Q235B steel grade with thickness of 7.8 mm.Since online application of the sophisticated CTC process control system based on these models,run-out table cooling control system has been running stably and reliably to produce resource-saving,low-cost steels with smaller grain size.
基金Foundation item： Supported by National Natural Science Foundation of China（A10071008） . Acknowledgements Here the author thank Professor Wang Zikun, Li Zhanbing and Li Zenghu sincerely for their guidance and encouragement.
文摘In this paper, we investigate the interacting super-Brownian motion depending on population size. This process can be viewed as the high density limit of a sequence of particle systems with branching mechanism depending on their population size. We will construct a limit function-valued dual process.
文摘To explore the relationship between such a construct and an existing continence score. METHODSA retrospective study of incontinent patients who underwent anal physiology (AP) was performed. AP results and Cleveland Clinic Continence Scores (CCCS) were extracted. An anal physiology score (APS) was developed using maximum resting pressures (MRP), anal canal length (ACL), internal and external sphincter defects and pudendal terminal motor latency. Univariate associations between each variable, APS and CCCS were assessed. Multiple regression analyses were performed. RESULTSOf 508 (419 women) patients, 311 had both APS and CCCS measured. Average MRP was 51 mmHg (SD 23.2 mmHg) for men and 39 mmHg (19.2 mmHg) for women. Functional ACL was 1.7 cm for men and 0.7 cm for women. Univariate analyses demonstrated significant associations between CCCS and MRP (P = 0.0002), ACL (P = 0.0006) and pudendal neuropathy (P < 0.0001). The association between APS and CCCS was significant (P < 0.0001) but accounted for only 9.2% of the variability in CCCS. Multiple regression showed that the variables most useful in predicting CCCS were external sphincter defect, pudendal neuropathy and previous pelvic surgery, but only improving the scores predictive ability to 12.5%. CONCLUSIONThis study shows that the ability of AP tests to predict continence scores improves when considered collectively, but that a constructed summation model before and after multiple regression is poor at predicting the variability in continence scores.
文摘NIOSH ground control safety research program at Spokane,Washington,is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First,photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application.Second,field photogrammetric data is compared to crackmeter data from a deep underground mine.Accuracies were found to average 8 mm,but have produced results within 0.2 mm of true displacement,as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation.Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.
文摘Micro- injury （exercise-induced muscle damage, EIMD） will cause a temporary decline in muscle function, if not handled properly, it could cause more serious injury or overtraining, and even lead to the end of the athletes ＇ sports life. However, some studies have shown that an appropriate period of eccentric exercise training resulted in EIMD while promoted heart muscle fiber hypertrophy and corresponding muscle growth faster than exercise training, and there are the typical ＂ repetitive training effect＂ , ie after a period of the EIMD recovery, the muscle＇ s injury or delayed onset muscle soreness （DOMS） caused by the same movement is significantly reduced. So its deep study could help to guide the athlete to avoid or mitigate the negative effects which brought by EIMD, while could help to further clarify the process of the body to adapt to exercise training or mechanism.
