转子叶片数对翅板摆动泵流场的影响

针对转子叶片数影响着翅板摆动泵流场及工作性能的问题,为研究不同叶片数下,翅板摆动泵内部流场的变化情况,利用动网格和UDF技术,对叶片数分别为2、3、4、5和6的翅板摆动泵的二维流场进行了研究,对其在运动过程中的工作性能进行了分析。首先,根据翅板摆动泵的工作原理及其转子的运动方式,分析了转子叶片数与泵排量、容积效率的关系;然后,利用Mesh软件进行了网格划分,并结合RNG k-ε湍流模型,编写了UDF文件,对不同叶片数下的翅板摆动泵进行了数值模拟;最后,根据仿真得到的压力及速度分布云图,对比分析了不同叶片数下翅板摆动泵的工作性能。研究结果表明:当转子叶片数为2时,摆动泵吸油腔和排油腔的压力分布都很均匀,流速变化较平缓;随着转子叶片数的增加,吸油腔出现不同程度的低压区域及局部流速增大的现象,而且当叶片数为4、5、6时,在排油腔的弧形壁面与直线壁面间的夹角区域会出现流速降低的现象;经过综合对比可知,当叶片数为2时,翅板摆动泵的工作性能最好。

Energy Dissipation with Geometric Parameters in Unbaffled Surface Aerator

The dissipation rate of turbulent kinetic energy （ ε ） is the key process parameters for mixing in surface aerators. At constant dynamic variables （rotational speed）, ε is greatly affected by the geometric parameters, such as impeller diameter, cross-sectional area of the tank, liquid height, rotor blade length and immersion height. By doing numerical computation by visimix, present work analyzes the effect of non-dimensional （which is non-dimensionalized through rotor diameter） geometric parameters on ε. With an increase in liquid height, there is an increase in the case of energy dissipation. In the case of tank area and blade length, it is vice versa. Energy dissipation is not affected by the variation in immersion height of the impeller.

Influence of a Deflector or a Wall on Savonius Rotor Efficiency

The Savonius rotor is a vertical axis-wind machine composed of two half cylindrical blades presenting a central gap. It is a slow velocity machine compared with horizontal wind machines. Its efficiency is about twenty per cent. In this work experimental tests are presented using two kind of deflectors placed in front of the resistive blade. Such disposition allows to hide the resistant blade and to guide the flow toward the motrice blade. Two deflectors have been used： a short one and a long one. The results obtained in wind tunnel have shown that the long deflector is the more efficient, essentially for high values of the tip speed ratio. One has been interested, using a numerical approach, in the study of the influence of a wall on the aerodynamical field near the rotor.

Blade Parameterization and Aerodynamic Design Optimization for a 3D Transonic Compressor Rotor

The present paper describes an optimization methodology for aerodynamic design of turbomachinery combined with a rapid 3D blade and grid generator （RAPID3DGRID）, a N.S. solver, a blade parameterization method （BPM）, a gradient-based parameterization-analyzing method （GPAM）, a response surface method （RSM） with zooming algorithm and a simple gradient method. By the use of blade parameterization method a transonic com- pressor rotor can be expressed by a set of polynomials, and then it enables us to transform coordinate-expressed blade data to parameter-expressed and then to reduce the number of parameters. With changing any one of the parameters and by applying grid generator and N.S. solver, we can obtain several groups of samples. Here only ten parameters were considered to search an optimized compressor rotor. As a result of optimization, the adiabatic efficiency was increased by 1.73%.

Numerical Investigations on the Steady and Unsteady Leakage Flow and Heat Transfer Characteristics of Rotor Blade Squealer Tip

The steady and unsteady leakage flow and heat transfer characteristics of the rotor blade squealer tip were conducted by solving Reynolds-Averaged Navier-Stokes （RANS） equations with k-co turbulence model. The first stage of GE-E3 engine with squealer tip in the rotor was adopted to perform this work. The tip clearance was set to be 1% of the rotor blade height and the groove depth was specified as 2% of the span. The results showed that there were two vortexes in the tip gap which determined the local heat transfer characteristics. In the steady flow field, the high heat transfer coefficient existed at several positions. In the unsteady case, the flow field in the squealer tip was mainly influenced by the upstream wake and the interaction of the blades potential fields. These unsteady effects induced the periodic variation of the leakage flow and the vortexes, which resulted in the fluctuation of the heat transfer coefficient. The largest fluctuation of the heat transfer coefficient on the surface of the groove bottom exceeded 16% of the averaged value on the surface of the squealer tip.

Analysis of Internal Cooling Geometry Variations in Gas Turbine Blades

The present investigation analyzes the effects of major geometrical modifications to the interior of a convectioncooled gas turbine rotor blade. The main focus lies on the flow of the leading edge channels and the impact on theheat transfer. An experimental approach is performed with flow visualization via paint injection into water. Alsonumerical calculations are carried out in two sets, on the one hand water calculations accompanying the experimentsand on the other hand conjugate heat transfer calculations under realistic engine conditions. The latter calculationsare still ongoing delivering preliminary results.Five geometry configurations are investigated, three of them with differing turbulator arrangements in the leadingedge channels. The operating point of the base configuration is set to Re = 50,000 at the inlet while for the modifiedgeometries the pressure ratio is held constant compared to the base.Among several investigated configurations one could be identified that leads to a heat transfer enhancement inone leading edge channel 7 % larger compared to the base.

Numerical analysis and experimental investigation of wind turbine blades with innovative features:Structural response and characteristics

Innovative features of wind turbine blades with flatback at inboard region,thick airfoils at inboard as well as mid-span region and transversely stepped thickness in spar caps have been proposed by Institute of Engineering Thermophysics,Chinese Academy of Sciences(IET-Wind)in order to improve both aerodynamic and structural efficiency of rotor blades.To verify the proposed design concepts,this study first presented numerical analysis using finite element method to clarify the effect of flatback on local buckling strength of the inboard region.Blade models with various loading cases,inboard configurations,and core materials were comparatively studied.Furthermore,a prototype blade incorporated with innovative features was manufactured and tested under static bending loads to investigate its structural response and characteristics.It was found that rotor blades with flatback exhibited favorable local buckling strength at the inboard region compared with those with conventional sharp trailing edge when low-density PVC foam was used.The prototype blade showed linear behavior under extreme loads in spar caps,aft panels,shear web and flatback near the maximum chord which is usually susceptible to buckling in the blades according to traditional designs.The inboard region of the blade showed exceptional load-carrying capacity as it survived420%extreme loads in the experiment.Through this study,potential structural advantages by applying proposed structural features to large composite blades of multi-megawatt wind turbines were addressed.

Numerical Investigation of Influence of Rotor/Stator Interaction on Blade Boundary Layer Flow in a Low Speed Compressor

Numerical method was applied to the unsteady flow simulation at the mid span of a two-stage low speed compressor,and the blade boundary layer flow under rotor/stator interaction was investigated.By the model of wake/boundary layer interaction provided in this paper,the simulated blade frictional force and the boundary layer turbulent kinetic energy,the influence of wake/potential flow interaction on the blade boundary layer flow was analyzed in detail.The results show that under the condition of rotor/stator interaction,the wake is able to induce the stator laminar boundary layer flow to develop into turbulent flow within a certain range of wake interaction.In the stator suction boundary layer,an undisturbed region occurs behind the rotor wake,which extends the laminar flow range,and the wake with high turbulent intensity has the capability to control the boundary layer separation under adverse pressure gradient.

Effects of Perforation Number of Blade on Aerodynamic Performance of Dual-rotor Small Axial Flow Fans

Compared with single rotor small axial flow fans, dual-rotor small axial flow fans is better regarding the static characteristics. But the aerodynamic noise of dual-rotor small axial flow fans is worse than that of single rotor small axial flow fans. In order to improve aerodynamic noise of dual-rotor small axial flow fans, the pre-stage blades with different perforation numbers are designed in this research. The RANS equations and the standard k-e turbulence model as well as the FW-H noise model are used to simulate the flow field within the fan. Then, the aerodynamic performance of the fans with different perforation number is compared and analyzed. The results show that： （1） Compared to the prototype fan, the noise of fans with perforation blades is reduced. Additionally, the noise of the fans decreases with the increase of the number of perforations. （2） The vorticity value in the trailing edge of the pre-stage blades of perforated fans is reduced. It is found that the vorticity value in the trailing edge of the pre-stage blades decreases with the increase of the number of perforations. （3） Compared to the prototype fan, the total pressure rising and efficiency of the fans with perforation blades drop slightly.

Numerical Simulation of Ice Accretion Phenomena on Rotor Blade of Axial Blower

Ice accretion is the phenomenon that super-cooled water droplets impinge and accrete on a body. It is well known that ice accretion on blades and airfoils leads to performance degradation and severe accidents. For this reason, experimental investigations have been carried out using flight tests or icing tunnels. However, it is too expensive, dangerous, and difficult to set actual icing conditions. Hence, computational fluid dynamics is useful to predict ice accretion. A rotor blade is one of jet engine components where ice accretes. Therefore, the authors focus on the ice accretion on a rotor blade in this study. Three-dimensional icing phenomena on the rotor blade of a commercial axial blower are computed here, and ice accretion on the rotor blade is numerically investigated.

Aerodynamic Sweeping Study and Design for Transonic Compressor Rotor blades

The objective of the present paper is to study the sweep effect on the blade design performance of a transonic compressor rotor.The baseline to be modified and swept is a designed well efficient transonic single rotor compressor. The first part of the present study is concerning the sweep effect with straight leading edge.In this case fixing the hub section the swept blade is formed by tilting the leading edge with whole blade forwards and backwards axially.The second part is to use an optimization strategy with simple gradient-based optimum-searching method and multi-section blade parameterization technique to search and generate an optimal swept rotor with curved arbitrary leading edge.Its adiabatic efficiency is a little bit greater than that of the reference un-swept rotor.

Numerical Investigation on Super-cooled Large Droplet Icing of Fan Rotor Blade in Jet Engine

Icing(or ice accretion) is a phenomenon in which super-cooled water droplets impinge and accrete on a body.It is well known that ice accretion on blades and vanes leads to performance degradation and has caused severe accidents.Although various anti-icing and deicing systems have been developed,such accidents still occur.Therefore,it is important to clarify the phenomenon of ice accretion on an aircraft and in a jet engine.However,flight tests for ice accretion are very expensive,and in the wind tunnel it is difficult to reproduce all climate conditions where ice accretion can occur.Therefore,it is expected that computational fluid dynamics(CFD),which can estimate ice accretion in various climate conditions,will be a useful way to predict and understand the ice accretion phenomenon.On the other hand,although the icing caused by super-cooled large droplets(SLD) is very dangerous,the numerical method has not been established yet.This is why SLD icing is characterized by splash and bounce phenomena of droplets and they are very complex in nature.In the present study,we develop an ice accretion code considering the splash and bounce phenomena to predict SLD icing,and the code is applied to a fan rotor blade.The numerical results with and without the SLD icing model are compared.Through this study,the influence of the SLD icing model is numerically clarified.