钢芯铝绞线断股时的过热特性

为研究钢芯铝绞线断股时的过热特性,采用Ansoft Maxwell电磁场有限元分析软件对LGJ240/30 mm2型导线建立了二维结构模型,以电磁学理论为基础分析了不同断股数导线的欧姆损耗分布规律,得出结论:导线断股数越大,各层导体欧姆损耗分布的不均匀性越明显,且越接近断股处欧姆损耗越大。设计并搭建了导线温度测量实验平台,对LGJ500/35 mm2型、LGJ240/30 mm2型、LGJ70/10 mm2型导线进行了不同断股程度、不同载流大小情况下的温升实验,得出结论:加载电流越大、导线断股数越多、导体层数越少,则温度升高越严重。

国内首台百万二次再热机组过热汽温调节特性探讨

介绍国内首台百万千瓦二次再热机组的情况,并与一次再热机组进行对比,采用二次再热技术能够进一步提高机组的热效率。通过二次再热机组运行中过热汽温的调整进行研究,以控制煤水比、减温水来调节过热汽温;合理调整二次风小风门开度,优化炉内燃烧状况;调整燃尽风反切角度,消除烟温偏差;调节后的过热汽温达到设计值,无明显汽温偏差。

串级模糊控制器在过热蒸汽温度控制中的应用

过热器是一个典型的非线性、时变、大迟延、大惯性和多随机干扰扰动的设备,数学模型难以建立。利用模糊控制不依赖被控对象的数学模型,将串级控制和模糊控制优势相结合,设计出过热蒸汽温度串级模糊控制方案。仿真结果表明,本控制策略比过热蒸汽温度串级控制具有更强的适应能力和良好的控制品质。

Self-heating tendency evaluation of sulfide ores based on nonlinear multi-parameters fusion

In order to reveal the nonlinear dynamics characteristics of unsteady self-heating process of sulfide ores, nine different kinds of sulfide ore samples from a pyrite mine in China were taken as experimental materials and their self-heating characteristics were measured in laboratory. Furthermore, the measured temperature was studied by integrating wavelet transform, nonlinear characteristic parameters extraction and fuzzy comprehensive evaluation. The results indicate that only the ore samples 1, 2, 6 and 9 have obvious self-heating phenomenon, and their self-heating initiative temperatures are 220 ℃, 239 ℃, 220 ℃ and 220 ℃, respectively, which means that they are difficult to produce self-heating under normal mining conditions. The correlation dimension of self-heating process is fraction and the maximum Lyapunov exponent is positive, which means that it is feasible to study the self-heating process based on chaotic dynamics theory. The nonlinearities of self-heating process of these four samples （ore samples 1, 2, 6 and 9） are 0.8227, 0.7521, 0.9401 and 0.8827 respectively and the order of the samples according to these results is： sample 6, sample 9, sample 1, sample 2, which is consistent with the measured results of self-heating characteristics. Therefore, the nonlinearity method can be used to evaluate the self-heating tendency of sulfide ores, and it is an effective verification of the reliability of measured results.

Study on the rheology of coal-oil slurries during heating at high pressure

Using the self-developed viscosity measuring device, the viscosity variations of coal-oil slurries with temperature increasing during coal-oil co-processing were studied. The results show that the viscosity of coal-oil slurries prepared by different kinds of oil varies differently during heating. The viscosity of the coal-oil slurry prepared by the catalytic cracking slurry （FCC） generally decreases during heating. However, the viscosity of the coal-oil slurry prepared by the high-temperature coal tar （CT） will peak at 338 ℃ during heating. The differences in viscosity variations of coal-oil slurries are analyzed. In addition to the temperature, the properties of the solvents and coal are the main influencing factors. Because the used coal contains a large number of polar functional groups, the swelling behavior of the coal in polar solvent （CT） is stronger than that in non-polar solvent （FCC）. The swelling effect of the coal can result in the appearance of the viscosity peak. Therefore, before 100 ~C, the solvent molecules entering into the coal pores is the main influencing factor of coal-oil slurries viscosity variations. After 100 ℃, the increasing of particle size of coal particles is the main influencing factor of coal-oil slurries viscosity variations.

An Experimental Study on Thermal Characteristics of Laurie Acid as a Latent Heat Storage Material during Melting Process

The objective of this study was to establish the thermal characteristics of the lauric acid (95% purity) as a latent heat storage material filled in the annulus of vertical concentric double pipe during its melting process,The temperature data were used to determine the thermal characteristics,including the temporal temperature variations and the effects of the mass flow rate and the inlet temperature of the heat transfer fluid on the heat transfer coefficient and the heat charging fraction during the melting process,The results indicated that the time to reach to heat charging fraction of 1.0 could be altered by changing the mass flow rate and the inlet temperature of the heat transfer fluid.

Experiment investigation on visualization and operating characteristics of closed loop plate oscillating heat pipe with parallel channels

Using ethanol or acetone as the working fluid, visualization of oscillations in steady state was observed visually by high-speed cameras, and temperature oscillating and heat transfer characteristics of closed-loop plate oscillating heat pipe with parallel channels(POHP-PC) were experimentally investigated by varying liquid filled ratios(50%, 70%, 85%), section scales(1 mm×1 mm and 1 mm×1.5 mm), inclination angles, working fluids and heating inputs. It was found that during operating there was mixed flow consisting of plug flow and annular flow in channels of oscillating heat pipe at steady-state. There was an equilibrium position for working fluid of condenser during oscillating, and periodic oscillations occurred up and down in the vicinity of equilibrium position. With heat input increasing, equilibrium position rose slowly as a result of vapor pressure of evaporation.Evaporation temperature oscillating amplitude possessed a trend of small-large-small and frequency trend was of small-large during steady-state. It may be generally concluded that temperature, whether evaporator or condenser, fluctuated sharply or rose continuously when oscillating heat pipe coming to dry burning state. Simultaneously, it was found that temperature difference of cooling water possibly dropped with heat input rising during dry burning state. Thermal resistance of No. 2 with acetone was lower than that of No. 1 during experiments, but No. 2 achieving heat transfer limit was earlier than No. 1. However, with ethanol, thermal resistance of No. 1 and No. 2 were similar with the heating input less than 110-120 W and filling ratios of 50% and 70%. And with filling ratio of 85%, heating transfer performance of No. 2 was better compared to No. 1 during all the experiments.

Quench Front Progression in a Superheated Porous Medium： Experimental Analysis and Model Development

In case of accident at a nuclear power plant, water sources may not be available for a long period of time and the core heats up due to the residual power. Any attempt to inject water during core degradation can lead to quenching and further fragmentation of core material. The fragmentation of fuel rods and melting of reactor core materials may result in the formation of a ＂debris bed＂. The typical particle size in a debris bed might reach few millimeters （characteristic length-scale： 1-5 mm）. The two-phase flow model for reflood of the degraded core is briefly introduced in this paper. It is implemented into the ICARE-CATHARE code, developed by IRSN （Institut de radioprotection et de surete nucleaire）, to study severe accident scenarios in pressurized water reactors. Currently, the French IRSN sets up two experimental facilities to study debris bed reflooding, PEARL and PRELUDE, and validate safety models. The PRELUDE program studies the complex two phase flow （water/steam）, in a porous medium （diameter 180 mm, height 200 mm）, initially heated to a high temperature （400℃ or 700℃）. On the basis of the experimental results, thermal hydraulic features at the quench front have been analyzed. The two-phase flow model shows a good agreement with PRELUDE experimental results.

Microstructure ＆ texture evolution and magnetic properties of high magnetic-induction 6.5% Si electrical steel thin sheet fabricated by a specially designed rolling route

Electrical steel sheets with 6.5%(mas fraction) Si with good shapes and superior magnetic inductions were successfully produced by a specially designed processing route including ingot casting, hot rolling and warm rolling both with interpass thermal treatment, and final annealing. The sheets were of 0.2 mm and 0.3 mm thick over 140 mm width. A detailed study of the microstructural and textural evolutions from the hot rolling to annealing was carried out by optical microscopy, X-ray diffraction and electron backscattered diffraction. The hot rolled sheet characterized by near-equiaxed grains was dominated by the mixture of <001>//ND fiber(λ-fiber), <110>//RD fiber(α-fiber) and <111>//ND fiber(γ-fiber) textures owing to the partial recrystallization and strain induced boundary migration(SIBM) during the hot rolling interpass thermal treatment. The static recovery and SIBM during the warm rolling interpass thermal treatment result in large and elongated warm rolling grains. The warm rolling texture is dominated by obvious λ, Goss and strong γ-fiber textures. The application of the interpass thermal treatment during hot and warm rolling significantly enhances the impact of SIBM during annealing, which is responsible for the formation of the moderate λ-fiber, some near-λ fiber texture components and the obviously weakened γ-fiber texture in the annealed sheet, leading to a higher magnetic induction compared to the commercially produced 6.5% Si steel by chemical vapor deposition(CVD).