Based on the engineering application, the angle range of rectifying airflow unit attaching diffusion tank is from 2.5° to 7.5°. In the range of average inlet velocity of 25.0 m/s to 55.0 m/s of diffusion tan...Based on the engineering application, the angle range of rectifying airflow unit attaching diffusion tank is from 2.5° to 7.5°. In the range of average inlet velocity of 25.0 m/s to 55.0 m/s of diffusion tank, numerical simulations of diffusion tank were done. The results of numerical simulations of diffusion tank are shown as follows： ③ In cases of the inlet velocity range from 25.0 m/s to 55.0 m/s, and the angle range of rectifying airflow unit from 2.5° to 7.5°, the average value of pressure losses decreases to the minimum when the angle is 4.5°.② In cases of the inlet velocity of 35.0 m/s, the pressure loss of diffusion tank decreases to the minimum when the angle of rectifying airflow unit is 5.5°. ③ As far as there are different angles of rectifying airflow unit, pressure loss increases gradually along with the addition of inlet velocity.展开更多
A numerical study is conducted to investigate the influence of inlet flow condition on tip leakage flow (TLF) and stall margin in a transonic axial rotor.A commercial software package FLUENT,is used in the simulation....A numerical study is conducted to investigate the influence of inlet flow condition on tip leakage flow (TLF) and stall margin in a transonic axial rotor.A commercial software package FLUENT,is used in the simulation.The rotor investigated in this paper is ND_TAC rotor,which is the rotor of one-stage transonic compressor in the University of Notre Dame.Three varied inlet flow conditions are simulated.The inlet boundary condition with hub distortion provides higher axial velocity for the incoming flow near tip region than that for the clean inflow,while the incoming main flow possesses lower axial velocity near the tip region at tip distortion inlet boundary condition.Among the total pressure ratio curves for the three inlet flow conditions,it is found that the hub dis-torted inlet boundary condition improves the stall margin,while the tip distorted inlet boundary condition dete-riorates compressor stability.The axial location of interface between tip leakage flow (TLF) and incoming main flow (MF) in the tip gap and the axial momentum ratio of TLF to MF are further examined.It is demonstrated that the axial momentum balance is the mechanism for interface movement.The hub distorted inflow could de-crease the axial momentum ratio,suppress the movement of the interface between TLF and MF towards blade leading edge plane and thus enhance compressor stability.展开更多
Optimal operation of the turbo blowers having an inlet vane has been studied to understand the blowers' operating performance.To analyze three-dimensional flow field in the turbo blowers serially connected,general...Optimal operation of the turbo blowers having an inlet vane has been studied to understand the blowers' operating performance.To analyze three-dimensional flow field in the turbo blowers serially connected,general analysis code,CFX,is introduced in the present work.SST turbulence model is employed to estimate the eddy viscosity.Throughout the numerical analysis,it is found that the flow rates of the turbo blowers can be controlled at the vane angle between 90 (full open condition) degrees and 60 degrees effectively,because pressure loss rapidly increases below 60 degree of a vane angle.Efficiency also has almost the same values from 90 degrees to 60 degrees of a vane angle.It is noted that the distorted inlet velocity generated in the small vane angle makes performance deterioration of the turbo blowers due to the local leading edge separation and the following non-uniform blade loading.展开更多
To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is prese...To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is presented.Moreover,a novel forebody design methodology which by rotating and assembling two waverider-based surfaces is firstly introduced in this paper.Some typical configurations are designed and their aerodynamic performances are evaluated by computational fluid dynamics.The results for forebodies analysis show that large volumetric efficiency,high lift-to-drag ratio,and uniformly distributed flowfield at the inlet cross section can be assured simultaneously.Furthermore,results of numerical simulation of four integrated configurations with various leading edge shapes,including three power-law curves and a cosine curve clearly show the advantage of high lift-to-drag ratio.Besides,the high pressure generated by the side wall of the airframe can be partly captured by the reasonably designed wings in the condition of small flight attack angle.Then the order of lift-to-drag ratio of four configurations at 0 degree flight attack angle is completely different from the condition of 4-degree flight attack angle.This result demonstrates that the curve shape of the leading edge is very important for the lift-to-drag ratio of the aircraft,and it should be further optimized under the cruising attack angle in future work.展开更多
文摘油浸式变压器主要由铁芯、绕组、绝缘系统和散热器构成,通过改变散热器的位置可以改变油箱进口处的油速,进而影响绕组的热点温度.通过有限元法,建立变压器在不同进口油速时绕组区域温度场与流场的流固耦合模型,分析绕组在不同进口油速时的热点温度变化,并通过光纤温度传感器直接测温实验验证模型的有效性.通过对比不同进口油速时绕组热点温度可知,油速在0.002~0.03 m/s之间,随着油速的增加绕组热点温度降低了3.2 K;在0.03~0.05 m/s之间,随油速增加热点温度降低缓慢,温度降低了0.5 K.
基金Supported by the National Natural Science Foundation of China （51074073） the Project of Hunan Provincial Science ＆ Technology Department （2010XK6066） the Project of Scientific Research Fund of Hunan Provincial Education Department （10C0675）
文摘Based on the engineering application, the angle range of rectifying airflow unit attaching diffusion tank is from 2.5° to 7.5°. In the range of average inlet velocity of 25.0 m/s to 55.0 m/s of diffusion tank, numerical simulations of diffusion tank were done. The results of numerical simulations of diffusion tank are shown as follows： ③ In cases of the inlet velocity range from 25.0 m/s to 55.0 m/s, and the angle range of rectifying airflow unit from 2.5° to 7.5°, the average value of pressure losses decreases to the minimum when the angle is 4.5°.② In cases of the inlet velocity of 35.0 m/s, the pressure loss of diffusion tank decreases to the minimum when the angle of rectifying airflow unit is 5.5°. ③ As far as there are different angles of rectifying airflow unit, pressure loss increases gradually along with the addition of inlet velocity.
基金supported by National Natural Science Foundation of China with project No.51010007 and No.51106153
文摘A numerical study is conducted to investigate the influence of inlet flow condition on tip leakage flow (TLF) and stall margin in a transonic axial rotor.A commercial software package FLUENT,is used in the simulation.The rotor investigated in this paper is ND_TAC rotor,which is the rotor of one-stage transonic compressor in the University of Notre Dame.Three varied inlet flow conditions are simulated.The inlet boundary condition with hub distortion provides higher axial velocity for the incoming flow near tip region than that for the clean inflow,while the incoming main flow possesses lower axial velocity near the tip region at tip distortion inlet boundary condition.Among the total pressure ratio curves for the three inlet flow conditions,it is found that the hub dis-torted inlet boundary condition improves the stall margin,while the tip distorted inlet boundary condition dete-riorates compressor stability.The axial location of interface between tip leakage flow (TLF) and incoming main flow (MF) in the tip gap and the axial momentum ratio of TLF to MF are further examined.It is demonstrated that the axial momentum balance is the mechanism for interface movement.The hub distorted inflow could de-crease the axial momentum ratio,suppress the movement of the interface between TLF and MF towards blade leading edge plane and thus enhance compressor stability.
基金supported by the Korea Institute of Industrial Technology Evaluation and Planning (ITEP) grant funded by the Ministry of Knowledge Economy(No. 10032063)
文摘Optimal operation of the turbo blowers having an inlet vane has been studied to understand the blowers' operating performance.To analyze three-dimensional flow field in the turbo blowers serially connected,general analysis code,CFX,is introduced in the present work.SST turbulence model is employed to estimate the eddy viscosity.Throughout the numerical analysis,it is found that the flow rates of the turbo blowers can be controlled at the vane angle between 90 (full open condition) degrees and 60 degrees effectively,because pressure loss rapidly increases below 60 degree of a vane angle.Efficiency also has almost the same values from 90 degrees to 60 degrees of a vane angle.It is noted that the distorted inlet velocity generated in the small vane angle makes performance deterioration of the turbo blowers due to the local leading edge separation and the following non-uniform blade loading.
基金supported by the National Natural Science Foundation of China (Grant No. 90916013)the guidance and help from Academician Li Tian and peer reviewers are gratefully acknowledged
文摘To aim at design requirements of high lift-to-drag ratio as well as high volumetric efficiency of next generation hypersonic airplanes,a body-wing-blending configuration with double flanking air inlets layout is presented.Moreover,a novel forebody design methodology which by rotating and assembling two waverider-based surfaces is firstly introduced in this paper.Some typical configurations are designed and their aerodynamic performances are evaluated by computational fluid dynamics.The results for forebodies analysis show that large volumetric efficiency,high lift-to-drag ratio,and uniformly distributed flowfield at the inlet cross section can be assured simultaneously.Furthermore,results of numerical simulation of four integrated configurations with various leading edge shapes,including three power-law curves and a cosine curve clearly show the advantage of high lift-to-drag ratio.Besides,the high pressure generated by the side wall of the airframe can be partly captured by the reasonably designed wings in the condition of small flight attack angle.Then the order of lift-to-drag ratio of four configurations at 0 degree flight attack angle is completely different from the condition of 4-degree flight attack angle.This result demonstrates that the curve shape of the leading edge is very important for the lift-to-drag ratio of the aircraft,and it should be further optimized under the cruising attack angle in future work.
