3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be effi...3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be efficient and stable. However, it has low calculation accuracy near the source, which thus gives it low overall accuracy. This paper proposes a joint traveltime calculation method to solve this problem. The method firstly employs the wavefront construction method （WFC）, which has a higher calculation accuracy than FMM in calculating traveltime in the small area near the source, and secondly adopts FMM to calculate traveltime for the remaining grid nodes. Due to the increase in calculation precision of grid nodes near the source, this new algorithm is shown to have good calculation precision while maintaining the high calculation efficiency of FMM, which is employed in most of the computational area. Results are verified using various numerical models.展开更多
A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technolog...A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technology of stream tracing and shock cutting.Comparison between the newly designed inlet and a typical sidewall compression inlet is given.The design Mach number and entrance shape of this new inlet are chosen according to the sidewall compression inlet.Numerical results show that most of the performance parameters of the internal waverider inlet are a bit higher than the sidewall inlet,such as the flow capture coefficient,total pressure recovery and the kinetic efficiency.The performances of these two inlets at off-design points are compared.The internal waverider inlet can capture more than 91% of incoming flow under all simulated conditions.Results show that internal waverider inlet using 3-D compression and high flow capture coefficient is a kind of fixed-geometry inlet with better performance.展开更多
Aim To investigate the effects of the incident orientation on the microwave attenuation. Methods Attenuation allowing microwave signal transmitting in an oblique or vertical direction through the solid propellant ex...Aim To investigate the effects of the incident orientation on the microwave attenuation. Methods Attenuation allowing microwave signal transmitting in an oblique or vertical direction through the solid propellant exhaust plume was computed, and the experiments were performed utilizing a lab scale solid rocket motor with a fully expanded nozzle. Results The predicted results accord well with the experimental results. Conclusion The microwave attenuation in the oblique path is greater than that in the vertical path.展开更多
Frequency sampling is one of the popular methods in FIR digital filter design. In the frequency sampling method the value of transition band samples, which are usually obtained by consulting a table, must be determi...Frequency sampling is one of the popular methods in FIR digital filter design. In the frequency sampling method the value of transition band samples, which are usually obtained by consulting a table, must be determined in order to make the attenuation within the stopband maximal. However, the value obtained by searching for table can not be ensured to be optimal. Evolutionary programming (EP), a multi agent stochastic optimization technique, can lead to global optimal solutions for complex problems. In this paper a new application of EP to frequency sampling method is introduced. Two examples of lowpass and bandpass FIR filters are presented, and the steps of EP realization and experimental results are given. Experimental results show that the value of transition band samples obtained by EP can be ensured to be optimal and the performance of the filter is improved.展开更多
Most operating radar systems don′t have sufficient frequency bandwidth to produce high range resolution(HRR) profile of a target. But we can use stepped frequency waveform in a narrow band coherent radar to obtai...Most operating radar systems don′t have sufficient frequency bandwidth to produce high range resolution(HRR) profile of a target. But we can use stepped frequency waveform in a narrow band coherent radar to obtain the HRR profile of a target. For moving targets which are of great importance in practical radar usage, autofocusing,i.e. phase correction, is a necessary and critical step of the synthetic HRR processing. The purpose of autofocusing is to remove the radial motion effect of the target from radar echoes, and only reserve the stepped frequency effect which is the basis of synthetic HRR capability. We investigate two autofocusing approaches for synthetic HRR radars using stepped frequency waveform in this paper. The first is motion fitting method. This method depends on a certain parametric model, and is computationally expensive. Then we propose the iterative dominant scatterer method. It is robust, non parametric and simple in computation in comparison with the motion fitting method. Experimental results based on data acquired by using a metallised scale model B 52 in a microwave anechoic chamber reveal the validity and effectiveness of the method.展开更多
Aim To study the influence of radar-target relative speed on frequency MMW high-resolution ore-dimension distance profile and the compensation for it. Methods Based on the distance travelled by the electromagnetic wa...Aim To study the influence of radar-target relative speed on frequency MMW high-resolution ore-dimension distance profile and the compensation for it. Methods Based on the distance travelled by the electromagnetic wave, analyses were made for the compensation algorithm and the expression of the inverse FFT base distance was given.The relative importance of different compensation terms was studied in great detail. The concept of searching compensation was put forward. Results and Condclusion Dcm-△Dvimis the be distance of inverse FFT transformation, the effect caused by the distance △Dim on one-dimension profile is negligible, and the effect caused by the distance Dvim should not be neglected and must be compensated.展开更多
The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selec...The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selected by the uniform design, and the inlet performance is analyzed by computational fluid dynamics （CFD）. Then complete quadratic polynomial response surface approximation models are constructed based on the performance analysis results and then used to replace theoriginal complex inlet performance model. The optimization is conducted using a multi-objective genetic algorithm NSGA-Ⅱ, and the Pareto optimal solution set is obtained. Results show that the uniform design and RSM can reduce the computational complexity of numerical simulation and improve the optimization efficiency.展开更多
The extended tanh method is further improved by generalizing the Riccati equation and introducing its twenty seven new solutions. As its application, the (2+ 1)-dimensional Broer-Kaup equation is investigated and then...The extended tanh method is further improved by generalizing the Riccati equation and introducing its twenty seven new solutions. As its application, the (2+ 1)-dimensional Broer-Kaup equation is investigated and then its fifty four non-travelling wave solutions have been obtained. The results reported in this paper show that this method is more powerful than those, such as tanh method, extended tanh method, modified extended tanh method and Riccati equation expansion method introduced in previous literatures.展开更多
In order to overcome the phenomenon of image blur and edge loss in the process of collecting and transmitting medical image,a denoising method of medical image based on discrete wavelet transform(DWT)and modified medi...In order to overcome the phenomenon of image blur and edge loss in the process of collecting and transmitting medical image,a denoising method of medical image based on discrete wavelet transform(DWT)and modified median filter for medical image coupling denoising is proposed.The method is composed of four modules:image acquisition,image storage,image processing and image reconstruction.Image acquisition gets the medical image that contains Gaussian noise and impulse noise.Image storage includes the preservation of data and parameters of the original image and processed image.In the third module,the medical image is decomposed as four sub bands(LL,HL,LH,HH)by wavelet decomposition,where LL is low frequency,LH,HL,HH are respective for horizontal,vertical and in the diagonal line high frequency component.Using improved wavelet threshold to process high frequency coefficients and retain low frequency coefficients,the modified median filtering is performed on three high frequency sub bands after wavelet threshold processing.The last module is image reconstruction,which means getting the image after denoising by wavelet reconstruction.The advantage of this method is combining the advantages of median filter and wavelet to make the denoising effect better,not a simple combination of the two previous methods.With DWT and improved median filter coefficients coupling denoising,it is highly practical for high-precision medical images containing complex noises.The experimental results of proposed algorithm are compared with the results of median filter,wavelet transform,contourlet and DT-CWT,etc.According to visual evaluation index PSNR and SNR and Canny edge detection,in low noise images,PSNR and SNR increase by 10%–15%;in high noise images,PSNR and SNR increase by 2%–6%.The experimental results of the proposed algorithm achieved better acceptable results compared with other methods,which provides an important method for the diagnosis of medical condition.展开更多
Based on the extended mapping deformation method and symbolic computation, many exact travelling wave solutions are found for the (3+1)-dimensional JM equation and the (3+1)-dimensional KP equation. The obtained solut...Based on the extended mapping deformation method and symbolic computation, many exact travelling wave solutions are found for the (3+1)-dimensional JM equation and the (3+1)-dimensional KP equation. The obtained solutions include solitary solution, periodic wave solution, rational travelling wave solution, and Jacobian and Weierstrass function solution, etc.展开更多
To improve the density of information storage,this paper introduces a kind of annular binary filters with super-resolution,Several of these filters have been designed based on the genetic algorithm,the simulations dem...To improve the density of information storage,this paper introduces a kind of annular binary filters with super-resolution,Several of these filters have been designed based on the genetic algorithm,the simulations demonstrate that the transverse gain of the filters can reach the value of 1.37.Thus they can remarkably decrease the recording spot size,which is helpful to improve the density of information storage and to make the depth of focus longer,and therefore they can avoid the mistake caused by the small undulation of the optical disk in the process of recording/reading the information.展开更多
Acoustic modal behavior is reported for an L-shape hydrophone array during the passage of a strong nonlinear internal wave packet. Acoustic track is nearly parallel to the front of nonlinear internal waves. Through mo...Acoustic modal behavior is reported for an L-shape hydrophone array during the passage of a strong nonlinear internal wave packet. Acoustic track is nearly parallel to the front of nonlinear internal waves. Through modal decomposition at the vertical array, acoustic modes are identified. Modal evolution along the horizontal array then is examined during a passing internal wave. Strong intensity fluctuations of individual modes are observed before and during the internal waves packet passes the fixed acoustic track showing a detailed evolution of the waveguide modal behavior. Acoustic refraction created either uneven distribution of modal energy over the horizontal array or additional returns observable at the entire L-shape array. Acoustic ray-mode simulations are used to phenomenologically explain the observed modal behavior.展开更多
The direct motion of Brownian particle is considered as a result of system derived by external nonequilibriumfluctuating. The cooperative effects caused by asymmetric ratchet potential, external rocking force and addi...The direct motion of Brownian particle is considered as a result of system derived by external nonequilibriumfluctuating. The cooperative effects caused by asymmetric ratchet potential, external rocking force and additive colorednoise drive a Brownian particle in the directed stepping motion. This provides this kind of motion of kinesin along amicrotubule observed in experiments with a reasonable explanation.展开更多
In this paper, two (3+1)-dimensional equations are investigated.Auto-Baecklund transformation is obtained, which is used with some ansatze to seek new types ofexact solutions including some arbitrary functions. When t...In this paper, two (3+1)-dimensional equations are investigated.Auto-Baecklund transformation is obtained, which is used with some ansatze to seek new types ofexact solutions including some arbitrary functions. When these arbitrary functions are taken assome special functions, these solutions possess abundant structures. These solutions containsoliton-like solutions and rational solutions.展开更多
As a combination of bio-mechanism and engineering technology, robot fish has become a multidisci- plinary research that mainly involves both hydrodynamics-based control and actuation technology. This paper presents a ...As a combination of bio-mechanism and engineering technology, robot fish has become a multidisci- plinary research that mainly involves both hydrodynamics-based control and actuation technology. This paper presents a simplified propulsive model for carangiform propulsion, which is a swimming mode suitable for high speed and high efficiency. The carangiform motion is modeled as an N-joint nscillating mechanism that is composed of two basic components： the streamlined fish body represented by a planar spline curve and its hmate caudal tail by an oscillating foil. The speed of fish＇s straight swimming is adjusted by modulating the joint＇s oscillating frequency, and its orientation is tuned by different joint＇s deflection. The results from actual experiment showed that the proposed simplified propulsive model could be a viable eandidate for application in aquatic： swimming vehicles.展开更多
In the paper results of passive tomography calculations have been presented to assess rockburst hazard and locate high seismic activity zones in the vicinity of longwall 306 in Zabrze Bielszowice coal mine. The area o...In the paper results of passive tomography calculations have been presented to assess rockburst hazard and locate high seismic activity zones in the vicinity of longwall 306 in Zabrze Bielszowice coal mine. The area of study was 1000 m in X direction by 900 m in Y direction. The zones of high values of P-wave propagation velocity have been found to correlate with the distribution of large seismic tremors.展开更多
基金supported by NSFC(Nos.41274120,41404085,and 41504084)
文摘3D traveltime calculation is widely used in seismic exploration technologies such as seismic migration and tomography. The fast marching method （FMM） is useful for calculating 3D traveltime and has proven to be efficient and stable. However, it has low calculation accuracy near the source, which thus gives it low overall accuracy. This paper proposes a joint traveltime calculation method to solve this problem. The method firstly employs the wavefront construction method （WFC）, which has a higher calculation accuracy than FMM in calculating traveltime in the small area near the source, and secondly adopts FMM to calculate traveltime for the remaining grid nodes. Due to the increase in calculation precision of grid nodes near the source, this new algorithm is shown to have good calculation precision while maintaining the high calculation efficiency of FMM, which is employed in most of the computational area. Results are verified using various numerical models.
文摘A new internal waverider inlet with a rectangular shape of entrance and exit in front view is designed at Ma=6.0.The design is based on a better basic flowfield ICFC than traditional one and derived with the technology of stream tracing and shock cutting.Comparison between the newly designed inlet and a typical sidewall compression inlet is given.The design Mach number and entrance shape of this new inlet are chosen according to the sidewall compression inlet.Numerical results show that most of the performance parameters of the internal waverider inlet are a bit higher than the sidewall inlet,such as the flow capture coefficient,total pressure recovery and the kinetic efficiency.The performances of these two inlets at off-design points are compared.The internal waverider inlet can capture more than 91% of incoming flow under all simulated conditions.Results show that internal waverider inlet using 3-D compression and high flow capture coefficient is a kind of fixed-geometry inlet with better performance.
文摘Aim To investigate the effects of the incident orientation on the microwave attenuation. Methods Attenuation allowing microwave signal transmitting in an oblique or vertical direction through the solid propellant exhaust plume was computed, and the experiments were performed utilizing a lab scale solid rocket motor with a fully expanded nozzle. Results The predicted results accord well with the experimental results. Conclusion The microwave attenuation in the oblique path is greater than that in the vertical path.
文摘Frequency sampling is one of the popular methods in FIR digital filter design. In the frequency sampling method the value of transition band samples, which are usually obtained by consulting a table, must be determined in order to make the attenuation within the stopband maximal. However, the value obtained by searching for table can not be ensured to be optimal. Evolutionary programming (EP), a multi agent stochastic optimization technique, can lead to global optimal solutions for complex problems. In this paper a new application of EP to frequency sampling method is introduced. Two examples of lowpass and bandpass FIR filters are presented, and the steps of EP realization and experimental results are given. Experimental results show that the value of transition band samples obtained by EP can be ensured to be optimal and the performance of the filter is improved.
文摘Most operating radar systems don′t have sufficient frequency bandwidth to produce high range resolution(HRR) profile of a target. But we can use stepped frequency waveform in a narrow band coherent radar to obtain the HRR profile of a target. For moving targets which are of great importance in practical radar usage, autofocusing,i.e. phase correction, is a necessary and critical step of the synthetic HRR processing. The purpose of autofocusing is to remove the radial motion effect of the target from radar echoes, and only reserve the stepped frequency effect which is the basis of synthetic HRR capability. We investigate two autofocusing approaches for synthetic HRR radars using stepped frequency waveform in this paper. The first is motion fitting method. This method depends on a certain parametric model, and is computationally expensive. Then we propose the iterative dominant scatterer method. It is robust, non parametric and simple in computation in comparison with the motion fitting method. Experimental results based on data acquired by using a metallised scale model B 52 in a microwave anechoic chamber reveal the validity and effectiveness of the method.
文摘Aim To study the influence of radar-target relative speed on frequency MMW high-resolution ore-dimension distance profile and the compensation for it. Methods Based on the distance travelled by the electromagnetic wave, analyses were made for the compensation algorithm and the expression of the inverse FFT base distance was given.The relative importance of different compensation terms was studied in great detail. The concept of searching compensation was put forward. Results and Condclusion Dcm-△Dvimis the be distance of inverse FFT transformation, the effect caused by the distance △Dim on one-dimension profile is negligible, and the effect caused by the distance Dvim should not be neglected and must be compensated.
文摘The uniform design and response surface methodology （RSM） are applied to the multi-objective optimization of a 2-D mixed compression scramjet inlet. The set of experimental design points on the design space is selected by the uniform design, and the inlet performance is analyzed by computational fluid dynamics （CFD）. Then complete quadratic polynomial response surface approximation models are constructed based on the performance analysis results and then used to replace theoriginal complex inlet performance model. The optimization is conducted using a multi-objective genetic algorithm NSGA-Ⅱ, and the Pareto optimal solution set is obtained. Results show that the uniform design and RSM can reduce the computational complexity of numerical simulation and improve the optimization efficiency.
文摘The extended tanh method is further improved by generalizing the Riccati equation and introducing its twenty seven new solutions. As its application, the (2+ 1)-dimensional Broer-Kaup equation is investigated and then its fifty four non-travelling wave solutions have been obtained. The results reported in this paper show that this method is more powerful than those, such as tanh method, extended tanh method, modified extended tanh method and Riccati equation expansion method introduced in previous literatures.
基金Project(2016JJ4074)supported by the Natural Science Foundation of Hunan Province,ChinaProject(14C0920)supported by the Hunan Provincial Education Department,ChinaProject(61771191)supported by the National Natural Science Foundation of China
文摘In order to overcome the phenomenon of image blur and edge loss in the process of collecting and transmitting medical image,a denoising method of medical image based on discrete wavelet transform(DWT)and modified median filter for medical image coupling denoising is proposed.The method is composed of four modules:image acquisition,image storage,image processing and image reconstruction.Image acquisition gets the medical image that contains Gaussian noise and impulse noise.Image storage includes the preservation of data and parameters of the original image and processed image.In the third module,the medical image is decomposed as four sub bands(LL,HL,LH,HH)by wavelet decomposition,where LL is low frequency,LH,HL,HH are respective for horizontal,vertical and in the diagonal line high frequency component.Using improved wavelet threshold to process high frequency coefficients and retain low frequency coefficients,the modified median filtering is performed on three high frequency sub bands after wavelet threshold processing.The last module is image reconstruction,which means getting the image after denoising by wavelet reconstruction.The advantage of this method is combining the advantages of median filter and wavelet to make the denoising effect better,not a simple combination of the two previous methods.With DWT and improved median filter coefficients coupling denoising,it is highly practical for high-precision medical images containing complex noises.The experimental results of proposed algorithm are compared with the results of median filter,wavelet transform,contourlet and DT-CWT,etc.According to visual evaluation index PSNR and SNR and Canny edge detection,in low noise images,PSNR and SNR increase by 10%–15%;in high noise images,PSNR and SNR increase by 2%–6%.The experimental results of the proposed algorithm achieved better acceptable results compared with other methods,which provides an important method for the diagnosis of medical condition.
文摘Based on the extended mapping deformation method and symbolic computation, many exact travelling wave solutions are found for the (3+1)-dimensional JM equation and the (3+1)-dimensional KP equation. The obtained solutions include solitary solution, periodic wave solution, rational travelling wave solution, and Jacobian and Weierstrass function solution, etc.
文摘To improve the density of information storage,this paper introduces a kind of annular binary filters with super-resolution,Several of these filters have been designed based on the genetic algorithm,the simulations demonstrate that the transverse gain of the filters can reach the value of 1.37.Thus they can remarkably decrease the recording spot size,which is helpful to improve the density of information storage and to make the depth of focus longer,and therefore they can avoid the mistake caused by the small undulation of the optical disk in the process of recording/reading the information.
基金Supported by U.S. Office of Naval Research,Ocean Acoustics Program(322OA)under Nos.N00014-11-1-0701 and N00014-13-1-0306
文摘Acoustic modal behavior is reported for an L-shape hydrophone array during the passage of a strong nonlinear internal wave packet. Acoustic track is nearly parallel to the front of nonlinear internal waves. Through modal decomposition at the vertical array, acoustic modes are identified. Modal evolution along the horizontal array then is examined during a passing internal wave. Strong intensity fluctuations of individual modes are observed before and during the internal waves packet passes the fixed acoustic track showing a detailed evolution of the waveguide modal behavior. Acoustic refraction created either uneven distribution of modal energy over the horizontal array or additional returns observable at the entire L-shape array. Acoustic ray-mode simulations are used to phenomenologically explain the observed modal behavior.
文摘The direct motion of Brownian particle is considered as a result of system derived by external nonequilibriumfluctuating. The cooperative effects caused by asymmetric ratchet potential, external rocking force and additive colorednoise drive a Brownian particle in the directed stepping motion. This provides this kind of motion of kinesin along amicrotubule observed in experiments with a reasonable explanation.
文摘In this paper, two (3+1)-dimensional equations are investigated.Auto-Baecklund transformation is obtained, which is used with some ansatze to seek new types ofexact solutions including some arbitrary functions. When these arbitrary functions are taken assome special functions, these solutions possess abundant structures. These solutions containsoliton-like solutions and rational solutions.
文摘As a combination of bio-mechanism and engineering technology, robot fish has become a multidisci- plinary research that mainly involves both hydrodynamics-based control and actuation technology. This paper presents a simplified propulsive model for carangiform propulsion, which is a swimming mode suitable for high speed and high efficiency. The carangiform motion is modeled as an N-joint nscillating mechanism that is composed of two basic components： the streamlined fish body represented by a planar spline curve and its hmate caudal tail by an oscillating foil. The speed of fish＇s straight swimming is adjusted by modulating the joint＇s oscillating frequency, and its orientation is tuned by different joint＇s deflection. The results from actual experiment showed that the proposed simplified propulsive model could be a viable eandidate for application in aquatic： swimming vehicles.
文摘In the paper results of passive tomography calculations have been presented to assess rockburst hazard and locate high seismic activity zones in the vicinity of longwall 306 in Zabrze Bielszowice coal mine. The area of study was 1000 m in X direction by 900 m in Y direction. The zones of high values of P-wave propagation velocity have been found to correlate with the distribution of large seismic tremors.
