静电自组装方法合成的具有多孔三维网络结构的Fe_3O_4/石墨烯复合材料作为高性能锂离子电池负极材料(英文)

采用静电自组装方法,分两步合成Fe(OH)3/GO前驱体(GO:氧化石墨烯),再通过水热反应和600°C高纯氮气气氛下煅烧,获得了Fe3O4/石墨烯复合材料.通过X射线衍射(XRD)、扫描电镜(SEM)、高分辨透射电镜(HRTEM)、拉曼(Raman)光谱等多种分析,发现该复合材料具有三维多孔石墨烯网络结构.把合成的这种Fe3O4/石墨烯复合材料作为锂离子电池负极材料,电化学测试结果表明其具有优良的电化学性能:首次放电容量为1390 mAh·g-1,50次循环后容量为819 mAh·g-1.通过对比实验表明,三维石墨烯网络结构的形成对复合材料的电化学循环稳定性起着关键作用.

阴极成分对镍氢电池性能影响的神经网络分析

用人工神经网络模型分析了镍氢电池阴极材料的合金成分对电化学容量衰减速度的影响。用“留一法”训练了模型，模型对训练样本的计算值与实测值在散点图中沿0～45°对角线分布，误差为：均方误差（MSE）为0．1195，相对均方误差（MSRE）为20．54％，拟合值（VOF）为1．9144。对合金成分的分析结果表明：电化学容量的衰减速度随Ni含量的增加而下降，随Co、Al和Si含量的增加而增大，La含量和Nd含量的影响不大。

Model Recognition of Astronauts Blood Flow Change Under Sustained +Gz Acceleration

Aim Using animals as object of experiment to acquire various patterns of low cerebral blood pressure and reduced blood capacity in cerebral tissues of astronauts due to the load of acceleration. Methods The isotope tracking technique was applied to mark the blood and record the dynamic curves of cerebral blood flow changes under various accelerations, and the relevant mathematical model was set up using the method of system recognition. Also the method of factor analyzing was used to select two out of the data collected by eight sensors as two factors. Results One of the two factors reflects the various patterns in the astronaut's upper body, the other for the lower body. Parameters of rise time, delay time and steady value reflect the results under different acceleration. Conclusion Whether for the upper body or the lower body, blood flow changes can be considered as a second order system model. This method provides a new technique and method of doing research on astronaut's endurance of acceleration and selecting astronauts.

Experimental study on heat generation and dissipation performance of PEV Lithium-ion battery

Based on the lithium-ion battery pure electric vehicle （PEV） application, two capacity types of batteries are applied in thermal characteristic experiments. With the experimental comparison method, battery thermal characteristics and heat generation mechanism are studied. Experiments of batteries in cases of different dimensions, batteries with different air cooling velocity and two capacity types of batteries in free convection environment are put forward. Battery heat generation performance, heat dissipation performance and comparison of different capacity types＇ batteries are researched and summarized. Conclusions of battery heat generation and dissipation in PEV applications, important battery thermal management factors and suggestions are put forward.

The Velocity Measurement of Two-phase Flow Based on Particle Swarm Optimization Algorithm and Nonlinear Blind Source Separation

In order to overcome the disturbance of noise,this paper presented a method to measure two-phase flow velocity using particle swarm optimization algorithm,nonlinear blind source separation and cross correlation method.Because of the nonlinear relationship between the output signals of capacitance sensors and fluid in pipeline,nonlinear blind source separation is applied.In nonlinear blind source separation,the odd polynomials of higher order are used to fit the nonlinear transformation function,and the mutual information of separation signals is used as the evaluation function.Then the parameters of polynomial and linear separation matrix can be estimated by mutual information of separation signals and particle swarm optimization algorithm,thus the source signals can be separated from the mixed signals.The two-phase flow signals with noise which are obtained from upstream and downstream sensors are respectively processed by nonlinear blind source separation method so that the noise can be effectively removed.Therefore,based on these noise-suppressed signals,the distinct curves of cross correlation function and the transit times are obtained,and then the velocities of two-phase flow can be accurately calculated.Finally,the simulation experimental results are given.The results have proved that this method can meet the measurement requirements of two-phase flow velocity.

Study on the heat transfer of cross flow in vertical upward tubes

A special device was designed to measure temperature difference in this study of heat transfer of water and oil cross flow inside vertical upward tubes. A new heat transfer correlation was obtained for cross flow. The experimental results showed that the dependence of heat transfer on Reynolds is much smaller in a narrow space than that in a wide space. It was found that the heat transfer correlation of cross flow in a narrow space is obviously different from that in a wide space, and that the heat transfer correlation obtained in a wide space may not be applicable to the cross-flow heat transfer in a narrow space. Further, the single-phase heat transfer capability of water cross flow was compared with that of oil cross flow. The experimental results showed that the average heat transfer coefficient of water is about 2～3 times that ofoil when they have the same superficial velocity.

谈数学课堂教学效率的提高

当前,数学课堂教学存在着不少问题,严重影响了数学课堂教学效率。要提高数学课堂教学效率就要 有明确的教学目标;适宜的教学容量和教学速度;灵活的教学方法以及精练的课堂用语。

The constant-volume propagating spherical flame method for laminar flame speed measurement

Laminar flame speed is one of the most important intrinsic properties of a combustible mixture. Due to its importance, different methods have been developed to measure the laminar flame speed. This paper reviews the constant-volume propagating spherical flame method for laminar flame speed measurement. This method can be used to measure laminar flame speed at high pressures and temperatures which are close to engine-relevant conditions. First, the propagating spherical flame method is introduced and the constant-volume method （CVM） and constant- pressure method （CPM） are compared. Then, main groups using the constant-volume propagating spherical flame method are introduced and large discrepancies in laminar flame speeds measured by different groups for the same mixture are identified. The sources of discrepancies in laminar flame speed measured by CVM are discussed and special attention is devoted to the error encountered in data processing. Different correlations among burned mass fraction, pressure, temperature and flame speed, which are used by different researchers to obtain laminar flame speed, are summarized. The performance of these correlations are examined, based on which recommendations are given. Finally, recommendations for future studies on the con- stant-volume propagating spherical flame method for laminar flame speed measurement are presented.