新型双楔式侧抽芯机构的研制

新型双楔式侧向抽芯机构既不同于斜导柱等机械抽芯机构,又不同于纯液压抽芯机构,而是采用机械与液压相结合的方式,利用液压为动力驱动机械抽芯机构,从而实现合模锁紧与开模抽芯。这种新型侧抽芯机构可大大减小液压缸尺寸,结构紧凑,避免了与注射成型机有关部件的干涉,同时方便侧抽芯型芯的制造、修配和调整。

Microstructural examination and mechanical properties of replicated aluminium composite foams

Open-cell aluminium foams can be produced with the structural replication of dimensional accuracy from polymeric foam patterns through a pressure infiltration casting process.The strength of open-cell foam is much less than that of the closed-cell counterpart,and thereby subjects to mainly functional applications.An improvement in mechanical properties of the foams can be implemented with the addition of ceramic particles.In the present study,the composite foams were produced using AC3A alloy added with varying contents of SiC particles.The resultant foams have ceramic particles embedded in the alloy matrix and on the strut surface.Higher volume fraction of ceramic particles resulted in an increase in the compressive strength,energy absorption and microhardness of the foams.The improvement of these properties is due to the modification of the microstructure of the foams and the increased strength in the node and struts at which the ceramic particles reside.

Simulation and experimental verification of interfacial interactions in compound squeeze cast Al/Al-Cu macrocomposite bimetal

The objective of this work was to investigate the thermal and mechanical interactions between the two components of a compound squeeze cast macrocomposite bimetal. First, an Al/Al-4.5wt.%Cu macrocomposite bimetal was fabricated by compound squeeze casting process. Then, heat transfer, solidification and distribution of the generated stresses along the interface region of the bimetal were analyzed using Thermo-Calc, ProCAST and ANSYS softwares, and structure, copper distribution and microhardness changes across the interface of the bimetal were studied. The results showed no noticeable change in the structure of the Al-4.5wt.%Cu insert and no obvious micromixing and diffusion of copper across the interface. Simulation results were in good agreement with the experimental ones only when an equivalent oxide layer at the interface was defined and its effect on heat transfer was considered. This layer caused up to 50% decrease in local liquid fraction formed on the surface of the insert. Simulation of the generated stresses showed a uniformly distributed stress along the interface which was significantly lower than the compressive strength of the oxide layer, resulting in its good stability during the fabrication process. It was postulated that this continuous oxide layer not only acted as a thermal barrier but prevented the direct metal-metal contact along the interface as well.

Effect of different processing parameters on interfacial heat-transfer behavior in high-pressure die-casting process

Vacuum die casting can reduce the'air entrapment'phenomenon during casting process.Based on the temperature measurements at metal-die interface with different processing parameters,such as slow shot speed(VL),high shot speed(VH),pouring temperature(Tp)and initial die temperature(Tm),inverse method was developed to determine the interfacial heat transfer coefficient(IHTC).The results indicate that a closer contact between the casting and die could be achieved when the vacuum system is used.It is found that the vacuum could strongly increase the values of IHTC and decrease the grain size in castings.The IHTC could have a higher peak value with increasing the Tp from680to720℃or the VL from0.1to0.4m/s.In addition,the influence of the VH and Tm on IHTC could be negligible.

Modelling and Control of Pressurized Molten Metal in Press Casting

This paper presents a modeling and control of molten metal＇s pressure in pressing process using an innovative iron casting developed by our group. In this method, molten metal is directly poured into a lower mold, and then pressed to fill cavity by an upper mold being lowered down. For complex liquid flow during pressing, the liquid＇s pressure changing inside vertical path with various contraction and expansion geometries is newly modeled via the unstationary Bernoulli equation. The mathematical model is derived for a control design of pressing. To conduct the pressing velocity design algorithm, an unknown parameter of proposed model considering viscous flow is identified by using CFD （Computational Fluid Dynamics） with heat flow calculation. Control performance using a multi-switching velocity pattern is confirmed as an effective control design using the pressure model, because the pressure fluctuation has discontinuous variation points. Substituting detailed information for mold shape, poured volume and initial temperature into a developed control input generator, an optimum pressing velocity design and a robust design for defect-free production are proposed by the design algorithm based on the construction of an inverse system comprised of the sequential switching from higher to lower speed. Consequently, the effectiveness of the pressing control with reasonable pressure suppression has been demonstrated through CFD.