Thermodynamics analysis and precipitation behavior of fine carbide in K416B Ni-based superalloy with high W content during creep

The precipitation behavior of carbide in K416 B superalloy was investigated by means of creep measurement and microstructure observation. The results show that nanometer M6 C particles discontinuously precipitate in the γ matrix or along the γ/γ′ interface of the alloy during high temperature tensile creep. Thereinto, the amount of fine M6 C carbide increases as creep goes on, and the coherent interfaces of M6 C phase precipitating from the γ matrix are {100} and {111} planes. The thermodynamics analysis indicates that the solubility of element carbon in the matrix decreases when the alloy is deformed by the axial tensile stress during creep, so as to cause the carbon segregating in the regions of stress concentration and combining with carbide-forming elements M（W, Co）, which promotes the fine M6 C carbide to precipitate from the γ matrix.

Effect of carbon on microstructures of Ti-45Al-3Fe-2Mo-xC alloy

The effect of carbon addition on the microstructures of TiAl-based alloy（Ti-45Al-3Fe-2Mo） was studied.The proportion of β/B2 phase reduces with the content of carbon increasing,while the colony size increases.With increasing the carbon content,the lamellar spacing first decreases from 267 nm（Ti-45Al-3Fe-2Mo） to 237 nm（Ti-45Al-3Fe-2Mo-0.3C） and 155 nm（Ti-45Al-3Fe-2Mo-0.5C）,but then increases to 230 nm（Ti-45Al-3Fe-2Mo-1.0C） with further increase in C level,which is affected by the inhibition of carbon atom and precipitation of carbides at the lamellar interface.Precipitation of carbides shows a response to aging time at 800 ℃.P-type carbides grow up at the boundaries and near the dislocation areas with the prolonging of aging time.And these carbides are projected different morphology in different beam directions（BD）.The effects of these microstructural modifications were examined and the observations were discussed.

Roles of Zr and Y in cast microstructure of M951 nickel-based superalloy

The influence of Zr and Y on the cast microstructure of a nickel-based superalloy was investigated by optical microscopy （OM）,scanning electron microscopy（SEM）,electron probe micro-analysis（EPMA）and X-ray diffraction（XRD）.Theγ＋γ′eutectic volume in the superalloy rises notably with the increase of Zr or Y content.Meanwhile,the morphologies of primary MC carbides change from needle and platelet-like to blocky shape with increasing Zr and Y doped.The XRD results show that the primary MC carbide lattice constant increases with Zr and Y additions,and EPMA investigation shows that the platelet-like MC carbides contain primarily Nb and C,while those carbides in blocky shape have 39.2%Zr and 39.6%Nb in average,.These influences on the cast microstructure can be attributed to the atomic size effects of Zr and Y.

Effect of hot extrusion and heat treatment on microstructure of nickel-base superalloy

Effects of hot extrusion (HEX) and heat treatment on prior particle boundary (PPB), MC carbides,γ′precipitates and grain size of nickel-base FGH96 superalloy were studied. The results show that PPB consists of largeγ′, MC carbides enriched with Ti, Nb and a modicum of oxides. Thereafter, it can efficaciously tune γ′ precipitate size from micrometer down to nanometer region and simultaneously results in the annihilation of PPB by HEX process. The activation energy for grain growth of as-HEXed FGH96 superalloy was measured to be 402.6 kJ/mol, indicating that γ′ precipitate serves the critical role in inhibiting grain growth under sub-solvus heat treatment. Moreover, the results reveal that grain growth is primarily restrained by MC carbide in the case of super-solvus temperature.

Effects of welding parameters and tool geometry on properties of 3003-H18 aluminum alloy to mild steel friction stir weld

Defect-free butt joints of 3003 Al alloy to mild steel plates with 3 mm thickness were performed using friction stir welding （FSW）. A heat input model reported for similar FSW was simplified and used to investigate the effects of welding speed, rotation speed and tool shoulder diameter on the microstructure and properties of dissimilar welds. The comparison between microstructure, intermetallics and strength of welds shows the good conformity between the results and the calculated heat input factor （HIF） achieved from the model. The joint strength is controlled by Al/Fe interface at HIF of 0.2-0.4, by TMAZ at HIF of 0.4-0.8 and by intermetallics and/or defects at HIF0.8.

Preparation and characterization of MWCNTs/LDHs nanohybrids for removal of Congo red from aqueous solution

The assembly of layered double hydroxides （LDHs） and multi-walled carbon nanotubes （MWCNTs） nanohybrids was prepared as MWCNTs/LDHs by co-precipitation. The synthesized nanoparticles were characterized by using XRD, FT-IR, SEM/EDX, TGA and BET. XRD and SEM studies proved that MWCNTs phases did not enter into the interlayers of LDHs, they dispersed over the LDHs surface homogeneously. BET results showed that MWCNTs/LDHs possessed hierarchically porous nanostructure with large surface area （124.974 m^2/g） and great pore volume （0.604 cm^3/g）. Batch experiments were conducted to study the adsorption efficiency of Congo red （CR）. It was worthy to note that MWCNTs/LDHs exhibited excellent adsorption performance with the maximum CR adsorption capacity of 595.8 mg/g in weak acidic environment. The adsorption kinetics and isotherm parameters can be well described by the pseudo-second-order and the Langmuir isotherm models, respectively. The thermodynamic studies indicated that the adsorption process was spontaneous and endothermic.

Phase precipitation behavior and tensile properties of as-cast Ni-based superalloy during heat treatment

The phase precipitation behavior and tensile properties of an as-cast Ni-based alloy,IN617B alloy,after solution heat treatment and long-term aging treatment were investigated.Ti(C,N),M6C and M23C6 are the primary precipitates in as-cast microstructure.After solution heat treatment,most of carbides dissolve into the matrix except a few fine Ti(C,N)within grains.During long-term aging at 700°C,the phase precipitation behaviors of the alloy are characterized as follows:(1)M23C6 carbides at grain boundaries(GBs)transform from film-like shape to cellular shape and gradually coarsen due to the decrease of the surface energy and element aggregation to GBs;(2)M23C6 carbides within grains have a bar-like morphology with a preferential growth direction[110]and have a cube-on-cube coherent orientation relationship with the matrixγ;(3)γ?particles inhibit the coarsening of M23C6 within grains by constraining the diffusion of formation elements.Furthermore,the tensile strength of the alloy obviously increases,but the ductility significantly decreases after the aging for 5000 h.The alloy has a relatively stable microstructure which guarantees the excellent tensile properties during long-term aging.

Effect of carbon on microstructure,mechanical properties and wear resistance of non-equiatomic Fe_(70)Co_(7.5)Cr_(7.5)Ni_(7.5)V_(7.5) medium-entropy alloys fabricated by powder metallurgy

In this study,non-equiatomic Fe_(70)Co_(7.5)Cr_(7.5)Ni_(7.5)V_(7.5) medium-entropy alloys(MEAs)with different carbon contents were prepared via mechanical ball-milling,cold pressing and vacuum sintering.The microstructural evolution,mechanical properties and wear resistance of the MEAs were investigated.Fe_(70)Co_(7.5)Cr_(7.5)Ni_(7.5)V_(7.5) exhibited a bodycentered cubic(bcc)structure withσphase precipitation.After adding 4 at%and 8 at%carbon,the phase composition of the alloys was transformed to bcc+MC+σand bcc+MC+M_(23)C_(6),respectively.The mechanical properties and wear resistance were observed to be significantly enhanced by the formation of carbides.Increasing the carbon content,the corresponding bending strength and hardness increased from 1520 to 3245 MPa and HRC 57.2 to HRC 61.4,respectively.Further,the dominant wear mechanism changed from the adhesion wear to the abrasion wear.Owing to the evenly distributed carbides and precipitated nanocarbides,Fe_(64.4)Co_(6.9)Cr_(6.9)Ni_(6.9)V_(6.9)C_(8) revealed an extremely low specific wear rate of 1.3×10^(−6) mm_(2)/(N·m)under a load of 10 N.

Anion Photoelectron Spectroscopy and Density Functional Theory Studies of AuC_(n)^(-/0)(n=3-8):Odd-Even Alternation in Electron Binding Energies and Structures

We measured the photoelectron spectra of AuC_(n)^(-)(n=3-8)and conducted theoretical study on the structures and properties of AuC_(n)^(-/0)(n=3-8).It is found that the photoelectron spectra of AuC_(n)^(-)exhibit odd-even alternation.The spectral features of AuC_(3)^(-),AuC_(5)^(-),and AuC_(7)^(-)are much broader than those of AuC_(4)^(-),AuC_(6)^(-),and AuC_(5)^(-).The vertical detachment energies of AuC_(3)^(-),AuC_(5)^(-),and AuC_(7)^(-)are lower than those of AuC_(4)^(-),AuC_(6)^(-),and AuCs_(8)^(-).The most stable structures of AuC_(n)^(-)(n=3-8)are chain structures.The most stable structures of neutral AuC_(n)(n=3-8)are linear structures except that those of AuC_(3) and AuC_(5) are slightly bent.The calculated∠AuCC angles,Au-C bond lengths,and the charges on Au atom also show odd-even alternations,consistent with the experimental observations.

Photoelectrocatalytic CO2 reduction based on metalloporphyrin-modified TiO2 photocathode

The conversion of CO2 and water to value-added chemicals under sunlight irradiation, especially by photoelectrocatalytic reduction process, is always a dream for human beings. A new artificial photosynthesis system composed of a metalloporphyrin-functionalized TiO2 photocathode and BiVO4 photoanode can efficiently transform CO2 and water to methanol, which is accompanied by oxygen release. This photoelectrocatalytic system smoothly produces methanol at a rate of 55.5 μM h^–1 cm^– 2, with 0.6 V being the membrane voltage in plants. The production of hydrogen can also be observed when the voltage is more than 0.75 V, due to photocatalysis. Our results evidently indicate that the molecules of metalloporphyrin attached onto the surface of anatase (TiO2) behave as chlorophyll, NADP, and Calvin cycle in plant cells.

Preparation of gold clusters on metal oxides by deposition-precipitation with microwave drying and their catalytic performance for CO and sulfide oxidation

Gold clusters and small nanoparticles supported on metal oxides could be prepared by deposition‐precipitation followed by microwave irradiation as a drying method and then calcination.The drying method influenced the size of the Au particles.Au(III)was partly reduced during conventional oven drying,resulting in Au aggregates.In contrast,Au(III)was preserved during microwave drying owing to rapid and uniform heating,and the Au diameter was minimized to1.4nm on Al2O3.This method can be applied to several metal oxide supports having different microwave absorption efficiencies,such as MnO2,Al2O3,and TiO2.These catalysts exhibited higher catalytic activities for CO oxidation at low temperature and for selective aerobic oxidation of sulfide than those prepared by conventional methods.

Effect of solidification rate on MC-type carbide morphology in single crystal Ni-base superalloy AM3

In order to study the effect of the withdrawing rate on carbide morphology,MC-type carbide in single crystal superalloy AM3 was systematically investigated with sample growth rates from 3.5 μm/s to 500 μm/s.The carbide morphologies were investigated by scanning electron microscopy(SEM),and the electron probe microanalysis(EPMA) was used to characterize the carbide composition.The results indicate that the solidification rate is the important factor governing MC carbide growth morphology,size and distribution,composition and growth mechanism.With the increase of withdrawing rate,nodular,rod-like,Chinese script types of carbide morphology are observed.For the low withdrawing rate,with the increase of withdrawing rate,the carbide size becomes larger.For the case of dendritic interface,the carbide size becomes smaller with refinement of dendrites as withdrawing rate increases.The volume fraction of carbides increases with the withdrawing rate increasing.

Recycle Demetallating Process for Hydrocarbonaceous Feedstocks

The development and research on the recycle demetallating process are introduced. It shows the recycle demetallating process is effective on removing metal elements in heavy crude oil, especially with regard to calcium, through commercial application in delayed coking unit. Finally, the ash content in petroleum coke can be decreased to less than 0.5%, which complies with the IB coke standard. At the same time, the recycle demetallating process is an environmentally friendly technique, which has little effect on production quality and equipment corrosion.

In situ One-Pot Fabrication of MoO3-x Clusters Modified Polymer Carbon Nitride for Enhanced Photocatalytic Hydrogen Evolution

Developing low-cost and high-efficient noble-metal-free cocatalysts has been a challenge to achieve economic hydrogen production.In this work,molybdenum oxides(MoO3-x)were in situ loaded on polymer carbon nitride(PCN)via a simple one-pot impregnation-calcination approach.Different from post-impregnation method,intimate coupling interface between high-dispersed ultra-small MoO3-xnanocrystal and PCN was successfully formed during the in situ growth process.The MoO3-x-PCN-X(X=1,2,3,4)photocatalyst without noble platinum(Pt)finally exhibited enhanced photocatalytic hydrogen performance under visible light irradiation(λ>420 nm),with the highest hydrogen evolution rate of 15.6μmol/h,which was more than 3 times that of bulk PCN.Detailed structure-performance revealed that such improvement in visible-light hydrogen production activity originated from the intimate interfacial interaction between high-dispersed ultra-small MoO3-xnanocrystal and polymer carbon nitride as well as efficient charge carriers transfer brought by Schottky junction formed.

Density of Electron States and Volume of Solution of Hydrogen in SiC Alloys

The new reactor concepts are characterized by higher efficiency, better utilization of nuclear fuel and nuclear waste minimization. This approach means that it is necessary to continue a continued research and test of new materials in order to apply them in new reactors. In this study, the authors fbcused on the analysis of SiC alloys because, due to their particular properties, this alloy can be used in high temperature conditions where the pure silicon, semiconductor material par excellence, is inadequate to support them.