The effect of small tool pin profiles on the microstructures and mechanical properties of 6061 aluminum alloy joints using friction stir welding （FSW） technique was investigated. Three different tool pin profiles： ...The effect of small tool pin profiles on the microstructures and mechanical properties of 6061 aluminum alloy joints using friction stir welding （FSW） technique was investigated. Three different tool pin profiles： threaded tapered cylindrical （T1）, triangular （T2） and square （T3） were used to produce the joints. The results indicate that the weld joints are notably affected by joining with different tool pin profiles. The triangular tool pin profile produces thebest metallurgicaland mechanical weld properties compared with other tool pin profiles. Besides, the lowest tensile strength and microhardness are obtained for the joint friction stir welded with square tool pin profile. It is observed that the smaller tool pin profile and shoulder diameter lead to narrow region of heat affected zone （HAZ） and a desired level of softening. The fracture surface examination shows that the joints are also affected when welding with different types of tool pin profiles. The fracture surface shows that the triangular specimen fails with a ductile fracture mode during the tensile test, while the brittle fracture modes are observed in the joints fabricated with other tool pin profiles （T1 and T3）.展开更多
In this paper, the microcellular silicone rubber foams, strengthened with tetrapod-like Zinc Oxide whisker（T-ZnOw） are prepared. Through further characterization, it can be seen that the average cell diameter size o...In this paper, the microcellular silicone rubber foams, strengthened with tetrapod-like Zinc Oxide whisker（T-ZnOw） are prepared. Through further characterization, it can be seen that the average cell diameter size of the filled with T-ZnOw is reduced. The distribution uniformity of microcellulars is improved obviously with increasing T-ZnOw filler. The reason that introduction of T-ZnOw can greatly enhance mechanical properties of the microcellular silicone rubber foams is its good interfacial adhesion with the matrix contributes. It is also found that the reducing effects of T-ZnOw on the compressive stress relaxation ratio of microcellular silicone rubber foams, and the improvement is obvious with increasing T-ZnOw filler.展开更多
基金supported by the grant No.900100338 of the Universiti Malaysia Perlis (Uni MAP)the outstanding support provided by the staff in the School of Materials Engineering in Uni MAP+1 种基金the Centre for Low Carbon Transport and Institute for Vehicle System Engineering in Universiti Teknologi Malaysia (UTM)the School of Materials Engineering and Mineral Resources in Universiti Sains Malaysia (USM)
文摘The effect of small tool pin profiles on the microstructures and mechanical properties of 6061 aluminum alloy joints using friction stir welding （FSW） technique was investigated. Three different tool pin profiles： threaded tapered cylindrical （T1）, triangular （T2） and square （T3） were used to produce the joints. The results indicate that the weld joints are notably affected by joining with different tool pin profiles. The triangular tool pin profile produces thebest metallurgicaland mechanical weld properties compared with other tool pin profiles. Besides, the lowest tensile strength and microhardness are obtained for the joint friction stir welded with square tool pin profile. It is observed that the smaller tool pin profile and shoulder diameter lead to narrow region of heat affected zone （HAZ） and a desired level of softening. The fracture surface examination shows that the joints are also affected when welding with different types of tool pin profiles. The fracture surface shows that the triangular specimen fails with a ductile fracture mode during the tensile test, while the brittle fracture modes are observed in the joints fabricated with other tool pin profiles （T1 and T3）.
文摘In this paper, the microcellular silicone rubber foams, strengthened with tetrapod-like Zinc Oxide whisker（T-ZnOw） are prepared. Through further characterization, it can be seen that the average cell diameter size of the filled with T-ZnOw is reduced. The distribution uniformity of microcellulars is improved obviously with increasing T-ZnOw filler. The reason that introduction of T-ZnOw can greatly enhance mechanical properties of the microcellular silicone rubber foams is its good interfacial adhesion with the matrix contributes. It is also found that the reducing effects of T-ZnOw on the compressive stress relaxation ratio of microcellular silicone rubber foams, and the improvement is obvious with increasing T-ZnOw filler.
