钛、锆变质处理对高铝锌合金凝固特性的影响

采用热分析、定向凝固 -液淬技术及金相定量分析、能谱分析和差热分析等手段 ,研究了钛盐和锆盐变质处理对高铝锌合金凝固特性的影响。结果表明 ,钛和锆能有效促进初生富铝相形核 ,减小其析出的过冷度 ,显著减轻合金的非平衡凝固倾向。

一个新的沉积变质型钛矿床的成矿模式及找矿方法

内蒙古羊蹄子山沉积变质型钛矿床是一个新的钛矿床类型。通过对地质、地球物理前提条件的研究和找矿方法试验,认为高精度磁法是找沉积变质型钛矿床的基本方法,重力为有效的找矿方法。在矿区北带磨石山以金红石为主的富钛矿体上有600μGal的重力异常,无磁异常;南带的羊蹄子山钛铁矿体上重力异常为500μGal,有60nT的弱磁异常。

Effect of combinative addition of Ti and Sr on modification of AA4043 welding wire and mechanical properties of AA6082 welded by TIG welding

To improve the mechanical properties of AA6082 weld welded by tungsten inert gas welding using AA4043 welding wire, the effect of addition of Ti and/or Sr on continuous cast and rolled AA4043 welding wire was investigated. Experimental results indicated that Ti and Sr are excellent modifiers, which improve the microstructure of the AA4043 welding wire and enhance the mechanical properties of the AA6082 weld. It was found that the combinative addition of Ti and Sr can effectively modify both the α（Al） dendrites and eutectic Si phases compared with individual addition of Ti or Sr. In addition, Ti and/or Sr also changed the microstructure of the AA6082 weld. The tensile strength of the AA6082 weld reached the maximum value when 0.08% Ti and 0.025% Sr were added simultaneously. These results indicate that the combinative addition of Ti and Sr can be an effective composite modifier.

提高钨合金白口铸铁抗冲击磨损能力的研究

研究了稀土、钒钛复合变质处理对钨合金白口铸铁组织和性能的影响。结果表明,变质处理后钨合金白口铸铁的微观组织中碳化物网络断裂,其抗冲击韧性和耐磨损性能显著提高。

Microstructure and mechanical properties of laser beam welded TC4/TA15 dissimilar joints

The microstructure and mechanical properties of laser beam welded dissimilar joints in TC4 and TA15 titanium alloyswere investigated. The results showed that the coarse columnar grains containing a large amount of acicular α and martensite α′ werepresent in the fusion zone (FZ), some residual α phases and martensite structure were formed in the heat-affected zone (HAZ) onTC4 side, and bulk equiaxed α phase of the HAZ was on TA15 side. An asymmetrical microhardness profile across the dissimilarjoint was observed with the highest microhardness in the FZ and the lowest microhardness in TA15 BM. The orders of yield strengthand ultimate tensile strength were as follows: TC4 BM > TC4/TC4 similar joint > TA15 BM > TA15/TA15 similar joint > TC4/TA15dissimilar joint, and increased while hardening capacity and strain hardening exponent decreased with increasing strain rate from1×10?4 s?1 to 1×10?2 s?1. The TC4/TA15 dissimilar joints failed in the TA15 BM, and had characteristics of ductile fracture atdifferent strain rates.

Influence of soaking time on semi-conductivity and nonlinear electrical properties of TiO_2-based varistor ceramics

We investigated the influence of soaking time on the semi-conductivity and nonlinear electrical properties of TiO2- based varistor ceramic samples. We used a single sintering process and fabricated six disk samples of （Sr, Bi, Si, Ta）-doped TiO2- based varistor ceramics sintered at 1 250℃ for 0.5 h, 1.0 h, 2.0 h, 3.0 h, 4.0 h, and 5.0 h, respectively. The samples were characterized by X-ray diffraction, breakdown voltage, and complex impedance. The results show that as the soaking time increases from 0.5 h to 5.0 h, the breakdown voltage drops before rising while the nonlinear coefficient increases and then decreases. We suggest that, considering both grain semi-conductivity and nonlinear electrical properties of the TiO2-based varistor ceramics, the optimal soaking time is between 2.0 h and 3.0 h.

Study of Dye Absorption in Carbon Nanotube-Titanium Dioxide Heterostructures

In this work, the authors present a study of dye absorption in TiO2 doped with CNTs （carbon nanotubes）. Absorption decreases exponentially with the increase of CNTs in the film, while morphological characterization, conducted by SEM （scanning electron microscope） and TEM （transmission electron microscope） microscopes, suggests that this behavior is strongly related to morphological structure of grown films. For CNTs amounts greater than 1%, the authors observe the formation of CNTs clusters randomly distribute on TiO2 bulk, which strongly reduces the film porosity quenching the dye absorption. Comparison with optical properties of CNT/TiO2 filmstudied in the previous work, suggest that the best level of doping is with 0.5% of CNTs. FTIR （Fourier transform infrared spectroscopy） measurements conducted on a series of pristine and doped samples clearly indicate the absence of change in allotropic species of TiO2, while AFM （atomic force microscope） analysis indicates that the sample roughness strongly changes with doping, preventing the dye adsorption. Finally, measurements of cell efficiency indicate an increase of 5% in cells with 0.5% of CNT doping and a decrease for greater values.